5033264 JOHNSON RELAY, ECM MAIN


5033264 RELAY, ECM MAIN JOHNSON BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ25E4SDS, BJ25E4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS RELAY
5033264 RELAY, ECM MAIN JOHNSON
Rating:
38

Buy RELAY, ECM MAIN 5033264 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$40.74
 

28-04-2023
6.0[2.70] Pounds
-: -
Johnson/Evinrude/OMC New OEM RELAY AY 5033264
Number on catalog scheme: 19
 

BRP JOHNSON entire parts catalog list:

BJ115L4SDA, BJ115PX4SDA, J115PL4SDA, J115PX4SDA 2006
BJ115L4SRC, BJ115X4SRC, J115PL4SRC, J115PX4SRC 2004
BJ115L4STS, BJ115X4STS, J115PL4STS, J115PX4STS 2003
BJ140CX4DR, J140CX4SDA 2006
BJ140CX4SRS, J140CX4SRC 2004
BJ140L4SDR, BJ140X4SDR, J140PL4SDA, J140PX4SDA 2006
BJ140PL4SRS, BJ140PX4SRS, J140PL4SRC, J140PX4SRS 2004
BJ200CX4DC 2006
BJ200X4SDC 2006
BJ225CX4DC 2006
BJ225X4SDC 2006
BJ25E4SDS, BJ25EL4SDS, J25E4SDC, J25EL4SDC 2006
BJ25E4SUC, BJ25EL4SUC, J25E4SUR, J25EL4SUR 2007
BJ25TE4SDS, BJ25TEL4SDS, J25TE4SDC, J25TEL4SDC 2006
BJ25TE4SUC, BJ25TL4SUC, J25TE4SUR, J25TEL4SUR 2007
BJ40PL4SDR, J40PL4SDE 2006
BJ40PL4SOC, J40PL4SOB 2005
BJ40PL4SRS, J40PL4SRM 2004
BJ50PL4SDR, J50PL4SDE 2006
BJ50PL4SOC, J50PL4SOB 2005
BJ50PL4SRS, J50PL4SRM 2004
BJ60PL4SDM, J60PL4SDM 2006
BJ60PL4SOA, J60PL4SOA 2005
BJ60PL4SRR, J60PL4SRR 2004
BJ60PL4STC, J60PL4STC 2003
BJ70PL4SDM, J70PL4SDM 2006
BJ70PL4SOA, J70PL4SOA 2005
BJ70PL4SRR, J70PL4SRR 2004
BJ70PL4STC, J70PL4STC 2003
BJ90PL4SDA, BJ90PX4SDA, J90PL4SDA, J90PX4SDA 2006
BJ90PL4SRC, BJ90PX4SRC, J90PL4SRC, J90PX4SRC 2004
BJ90PL4STS, BJ90PX4STS, J90PL4STS, J90PX4STS 2003
J10BL4SUM, J10EL4SUM 2007
J10EL4SDA 2006
J10EL4SOR, J10R4SOA, J10RL4SOA, J10TBL4SOB, J10TE4SOA, J10TEL4SOA 2005
J10RL4SDM 2006
J10TBL4SDE 2006
J10TBL4SUD, J10TE4SUB, J10TEL4SUB 2007
J10TE4SDM, J10TEL4SDM 2006
J115PL4SOR, J115PX4SOR 2005
J140CX4SOR 2005
J140CX4STS 2003
J140PL4SOR 2005
J140PL4STS, J140PX4STS 2003
J140PX4SOR 2005
J15EL4SDC 2006
J15EL4SOS, J15R4SOA, J15RL4SOA, J15TE4SOA, J15TEL4SOA 2005
J15EL4SUR 2007
J15RL4SDM 2006
J15TE4SDM, J15TEL4SDM 2006
J15TE4SUB, J15TEL4SUB 2007
BJ200CX4O, J200CX4SOC 2004,2005
J200CX4SRS 2004
BJ200X4SO, J200PX4SOC 2004,2005
J200PX4SRS 2004
BJ225CX4O, J225CX4SOC, J225CZ4SOS 2004,2005
J225CX4SRS 2004
BJ225X4SO, J225PX4SOC, J225PZ4SOS 2004,2005
J225PX4SRS 2004
J40PL4STC 2003
J50PL4STC 2003
J90PL4SOR, J90PX4SOR 2005

Information:


Table 1
Diagnostic Trouble Codes for the Air Filter Restriction Switch
J1939 Code Description Notes
107-2 Engine Air Filter 1 Differential Pressure : Erratic, Intermittent, or Incorrect This code indicates a fault in the circuit for the air filter restriction switch.
The Electronic Control Module (ECM) detects the following conditions:
The signal from the air filter restriction switch indicates a restriction.
The engine is not running.
The ECM has been powered for at least 6 seconds.
The warning lamp will come on.
Monitoring of air filter restriction when the engine is running will be disabled whilst this code is active. If the engine is equipped with an air filter restriction switch, the type of switch that is installed can be either "Normally Open" or "Normally Closed". The parameter for the type of switch that is installed can be set using the electronic service tool.Use the electronic service tool to check which type of switch is installed in the application before continuing with this procedure.Ensure that the parameter is set correctly for the type of switch that is installed in the application. Refer to the OEM for more information.
Table 2
Diagnostic Summary for a "Normally Open" Air Filter Restriction Switch
Engine Condition Switch State Active Diagnostic Code
Not running (key on) Open Normal condition
Running Open Normal Condition (no air filter restriction detected)
Not running Closed 107-2
Running Closed 107-15 or 107-16
Table 3
Diagnostic Summary for a "Normally Closed" Air Filter Restriction Switch
Engine Condition Switch State Active Diagnostic Code
Not running (key on) Open 107-2
Running Open 107-15 or 107-16
Not running Closed Normal condition
Running Closed Normal Condition (no air filter restriction detected) Note: An active 107–15 or 107–16 diagnostic code indicates that the air inlet is restricted. Refer to Troubleshooting, "Inlet Air Is Restricted".
Illustration 1 g03636737
Schematic diagram for an air filter restriction switch
Not all connectors are shown. Refer to the Electrical Schematic for the application.
Illustration 2 g02716382
View of the pin location on the P1 connector for the air filter restriction switch
(87) Air filter restriction switch
Table 4
Troubleshooting Test Steps Values Results
1. Check the Type of Switch that is Installed and Configured
A. Connect the electronic service tool to the diagnostic connector.
B. Turn the keyswitch to the ON position. Do not start the engine.
C. Use the electronic service tool to check that the "Air Filter Restriction Switch Installation Status" and the "Air Filter Restriction Switch Configuration" matches the type of switch that is installed.
Switch configuration
Result: An air filter restriction switch is installed and the "Air Filter Restriction Switch Installation Status" is "Not Installed".
Use the electronic service tool to change the "Air Filter Restriction Switch Installation Status" to "Installed". Ensure that the "Air Filter Restriction Switch Configuration" matches the type of switch that is installed.
Use the electronic service to check that the repair eliminates the fault.
Result: An air filter restriction switch is not installed and the "Air Filter Restriction Switch Installation Status" is "Not Installed". The "Air Filter Restriction Switch Configuration" is "Normally Closed".
Repair: Change the "Air Filter Restriction Switch Configuration" to "Normally Open."
Use the electronic service to check that the repair eliminates the fault.
Result: An air filter is installed and the "Air Filter Restriction Switch Installation Status" is installed. The "Air Filter Restriction Switch Configuration" does not match the type of switch that is installed.
Repair: Change the "Air Filter Restriction Switch Configuration" to match the type of switch that is installed.
Use the electronic service to check that the repair eliminates the fault.
Result: An air filter restriction switch is installed. The "Air Filter Restriction Switch Installation Status" is "Installed". The "Air Filter Restriction Switch Configuration" matches the type of switch that is installed.
Proceed to Test Step 2.
2. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P1/J1 connector.
B. Thoroughly inspect the connector for the air filter restriction switch.
C. Refer to Troubleshooting, "Electrical Connectors - Inspect".
D. Perform a 30 N (6.7 lb) pull test on each of the wires in the connectors that are associated with the air filter restriction switch.
E. Check the harness for abrasions and for pinch points from the switch back to the ECM.
Damaged wire or connector
Result: A damaged wire or damaged connector was found.
Repair: Repair the damaged wire or the damaged connector.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly connected and/or inserted and the harness is free of corrosion, of abrasion or of pinch points.
Proceed to Test Step 3.
3. Check for Active or Recently Logged Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Do not start the engine.
D. Use the electronic service tool to check whether a "Normally Open" or "Normally Closed" air filter restriction switch is installed in the application.
E. Check for any active or recently logged diagnostic codes. Wait at least 10 seconds for activation of the diagnostic codes.
Diagnostic codes
Result: A 107-2 diagnostic code is not active.
If the diagnostic code is recently logged, an intermittent fault may exist.
Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" to identify intermittent faults.
Result: A "Normally Open" switch is installed. A 107-2 diagnostic code is active.
A short circuit condition exists in the air filter restriction switch circuit.
Proceed to Test Step 4.
Result: A "Normally Closed" switch is installed. A 107-2 diagnostic code is active.
An open circuit condition exists in the air filter restriction switch circuit.
Proceed to Test Step 6.
4. Create an Open Circuit at the Switch Connector
A. Turn the keyswitch to the OFF position.


Parts relay JOHNSON:

5030783
 
5030783 RELAY, Starter motor
BJ40PL4SRS, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, J10EL4SRC, J10R4SNF, J10R4SR, J10R4STC, J15R4SNF, J15R4SR, J15R4STC, J15RL4SR, J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4S
5031483
 
5031483 RELAY, TNT
BJ115L4STS, BJ60PL4STC, BJ70PL4STC, BJ90PL4STS, J140CX4STS, J140PL4STS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC, J60PL4SNF, J70PL4SNF
5034362
RELAY, TNT
5034362 RELAY, TNT
BJ40PL4SRS, BJ50PL4SRS, BJ60PL4SOA, BJ60PL4SRR, BJ70PL4SOA, BJ70PL4SRR
5034606
RELAY, TRIM/TILT
5034606 RELAY, TRIM/TILT
BJ115L4SRC, BJ140CX4SRS, BJ140PL4SRS, BJ40PL4SOC, BJ50PL4SOC, BJ90PL4SRC, J115PL4SOR, J140CX4SOR, J140PL4SOR, J140PX4SOR, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS, J90PL4SOR
5036701
RELAY, TNT
5036701 RELAY, TNT
BJ115L4SDA, BJ140CX4DR, BJ140L4SDR, BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ40PL4SDR, BJ50PL4SDR, BJ60PL4SDM, BJ70PL4SDM, BJ90PL4SDA
Back to top