0446081 RELIEF VALVE JOHNSON
BJ10FAEDC, BJ10FAEUR, BJ5FRBECC, BJ5FRBEUS, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, HJ6FRECA, HJ6FREUR, J6R4SRC, J6R4STS, J8R4SRC, J8R4STS
RELIEF
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
BRP JOHNSON entire parts catalog list:
- CYLINDER & CRANKCASE » 0446081
BJ5FRBECC, BJ5FRBLECC, HJ5FRECA, HJ5FRLECA 1998
BJ5FRBEUS, BJ5FRBLEUS, HJ5FREUR, HJ5FRLEUR 1997
BJ8FRBECA, BJ8FRBLECA, J8FRECA, J8FRLECA, J8FRXECA 1998
BJ8FRBEDC, BJ8FRBLEDC, BJ8FRBXEDC, HJ8FREDC, HJ8FRLEDC, J8FREDC, J8FRXEDC 1996
BJ8FRBEUR, BJ8FRBLEUR, BJ8FRBXEUR, HJ8FREUR, HJ8FRLEUR, J8FREUR, J8FRXEUR 1997
HJ10FELECA, J10FOECA, J10FOLECA 1998
HJ6FRECA, HJ6FRLECA 1998
HJ6FREUR, HJ6FRLEUR 1997
J6R4SRC, J6RL4SRC 2004
J6R4STS, J6RL4STS 2003
J8R4SRC, J8RL4SRC 2004
J8R4STS, J8RL4STS 2003
Information:
Illustration 1 g01090281 (1) Water pump drive gear
Illustration 2 g00537659
Stub shaft for cluster gear
(2) Cluster gear Apply 9S-3263 Thread Lock Compound to the five bolts for the stub shaft. Tighten the five bolts for the stub shaft in the following sequence. See Illustration 2 for the numbering of the bolts. ... 1, 3, 4, 5, 2, 1, 2, 3, 4, 5, 1Apply 9S-3263 Thread Lock Compound to the four bolts that fasten the cluster gear to the stub shaft. Tighten the four bolts that fasten the cluster gear to the stub shaft to the following torque. ... 30 7 N m (22 5 lb ft)
Illustration 3 g01248404
(3) Camshaft gear
(12) Camshaft retainer bolts
(13) Seals
(14) Camshaft gear bolts
Illustration 4 g00593987
Torque sequence for the camshaft gear
(4) Align the timing mark on the camshaft gear with the timing mark on the front housing when the No. 1 piston is at top center. (3) Camshaft gear Lightly lubricate the O-ring seal on the outside of the camshaft sealing plate with a 50/50 mixture of 8T-2998 Lubricant and clean engine oil. Apply 9S-3263 Thread Lock Compound to the three bolts for the camshaft sealing plate. Tighten the three camshaft sealing plate bolts to the following torque. See Illustration 3. ... 12 3 N m (9 2 lb ft)Tighten the camshaft bolts in the following sequence. See Illustration 4 for the numbering of the bolts. ... 1, 4, 2, 5, 3, 6, 1, 4Tighten the six camshaft gear bolts to the following torque. ... 240 40 N m (175 30 lb ft) (5) Adjustable idler gear Install the plate with the oil groove toward the gear face. Apply 9S-3263 Thread Lock Compound to the three bolts that fasten the adjustable idler gear to the stub shaft. Tighten the three bolts for the adjustable idler gear to the stub shaft to the following torque. ... 30 7 N m (22 5 lb ft)Refer to Testing and Adjusting, "Gear Group (Front) - Time" for the backlash adjustment procedure. Backlash between the camshaft gear and the adjustable idler gear ... 0.3556 0.254 mm (0.0140 0.010 inch)Apply 9S-3263 Thread Lock Compound to the one bolt and five studs for the stub shaft. Tighten the one bolt and five nuts for the stub shaft to the following torque. ... 55 10 N m (41 7 lb ft) (6) Air compressor gear (if equipped) (7) Idler gear Apply 9S-3263 Thread Lock Compound to the one bolt and five studs for the stub shaft. Tighten the one bolt and five nuts for the stub shaft to the following torque. ... 55 10 N m (41 7 lb ft)Apply 9S-3263 Thread Lock Compound to the three bolts that fasten the idler gear to the stub shaft. Tighten the three bolts that fasten the idler gear to the stub shaft to the following torque. ... 30 7 N m (22 5 lb ft) (8) Gear for the fuel transfer pump drive (9) Align the timing mark on the crankshaft gear with the timing mark on the cluster gear. (10) Crankshaft gear (11) Oil pump drive gear