0314732 RETAINER PLATE, Brg. hsg. JOHNSON
100ESL71A, 100ESL72R, 100ML79S, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 85EL76D, 85EL77S, 85ESL69E, 85ESL70B
RETAINER
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$55.86
04-07-2024
2.0[0.90] Pounds
US: SEI Marine Products
SEI Marine Products-Compatible with Evinrude Johnson Retainer Plate 0314732 V4 Outboard Lower Units 1978-1998
SEI Marine Products This retainer plate replaces OE#: 0314732 and fits 400 series Evinrude/ Johnson V4 outboard lower units from 1978-1998. It also fits the 400 series and 800 series OMC Stringer sterndrive lower units from 1978-1985.
SEI Marine Products This retainer plate replaces OE#: 0314732 and fits 400 series Evinrude/ Johnson V4 outboard lower units from 1978-1998. It also fits the 400 series and 800 series OMC Stringer sterndrive lower units from 1978-1985.
Compatible models:
100ESL71A
100ESL72R
100ML79S
115EL77S
115ESL69E
115ESL70D
115ESL73M
115ESL74B
115ESL75E
115ETZ78C
115ML79R
115TXL77S
125ESL71C
125ESL72R
135ESL73M
135ESL74B
135ESL75E
140ML77S
140ML78C
140ML79R
85EL76D
85EL77S
85ESL69E
85ESL70B
85ESL71A
85ESL72R
85ESL73M
85ESL74B
85ESL75E
85ETLR78C
85ML79R
85TXLR77S
BJ115TLEDA
HJ88MSLEDC
J100MLCSC
J100STLCCA
J100STLCEM
J100STLEIE
J100STLEND
J100STLERC
J100STLESB
J100STLETS
J110MLCCA
J110MLCDC
J110MLCEM
J110MLCUR
J112TSLEDR
J112TSLEOC
J112TSLERS
J115JKLEOC
J115JKLERS
J115JLEIE
J115JLEND
J115JLEOR
J115JLERC
J115JLETS
J115MLCIH
J115MLCNB
J115MLCRD
J115MLCSA
J115MLCTE
J115MLESB
J115TSLECM
J115TSLEUA
J120TLAEM
J120TLAIE
J120TLAND
J120TLARC
J120TLASB
J120TLATF
J120TLCCA
J120TLCDC
J120TLCUR
J125ESXENR
J125ESXERK
J125ESXESS
J125ESXETA
J125ESXW
J140CXARC
J140CXATF
J140CXCCS
J140CXCEC
J140CXEIA
J140CXENM
J140CXESR
J140MLCIH
J140MLCNB
J140MLCSA
J140MLCTE
J140TLCDC
J140TLCRD
J140TLCUA
J85MLCSA
J85TTLEIE
J85TTLEND
J85TTLEOR
J85TTLERC
J85TTLETS
J88MSLCCC
J88MSLCER
J88MSLCUS
J88MSLEIM
J88MSLENB
J88MSLEOS
J88MSLERD
J88MSLESA
J88MSLETE
J88TSLEDR
J88TSLEOC
J88TSLERS
J90MLCDC
J90MLCIH
J90MLCNB
J90MLCRD
J90MLCTE
J90MLCUR
J90TSLECM
J90TSLEUA
SJ100WMPLM
SJ100WMPLZ
JOHNSON
BRP JOHNSON entire parts catalog list:
- GEARCASE » 0314732
100ML79S, 100TLR79S, 100TXLR79S 1979
115EL77S, 115ETL77 1977
115ESL69E, 115ESL69S 1969
115ESL70D 1970
115ESL73M 1973
115ESL74B, 115ETL74B 1974
115ESL75E, 115ETL75E 1975
115ETZ78C, 115ML78C, 115TXL78C 1978
115ML79R, 115TL79R, 115TXL79R 1979
115TXL77S 1977
125ESL71C 1971
125ESL72R 1972
135ESL73M 1973
135ESL74B, 135ETL74B 1974
135ESL75E, 135ETL75E 1975
140ML77S, 140TL77S, 140TXL77S 1977
140ML78C, 140TL78C, 140TX78C 1978
140ML79R, 140TL79R, 140TXL79R 1979
85EL76D, 85EL76G, 85ETLR76D, 85ETLR76G 1976
85EL77S, 85ETLR77S 1977
85ESL69E, 85ESL69M, 85ESL69S 1969
85ESL70B, 85ESL70D 1970
85ESL71A, 85ESL71H 1971
85ESL72R 1972
85ESL73M 1973
85ESL74B 1974
85ESL75E 1975
85ETLR78C, 85ML78C, 85TXLR78C 1978
85ML79R, 85TL79R, 85TXL79R 1979
85TXLR77S 1977
BJ115TLEDA, HJ115TXADA, J115JLEDA, J115TLEDA, J115TXADA 1996
BJ90TLEDA, HJ88MSLEDC, HJ90MLEDA, HJ90TXADA, J88MSLEDC, J90TLEDA 1996
HJ88MSLEDC, J88MSLEDC 1996
J100MLCSC, J100TRLCSC, J100TRXCSC 1980
J100STLCCA 1988
J100STLCEM 1989
J100STLEIE, VJ100SLEIE 1991
J100STLEND, VJ100SLEND 1992
J100STLERC 1994
J100STLESB, VJ100SLESB 1990
J100STLETS, VJ100SLETS 1993
J110MLCCA, J110TLCCA, J110TXCCA 1988
J110MLCDC, J110TLCDC, J110TLCDF 1986
J110MLCEM, J110TLAEM, J110TLCEM, J110TXCEM, TJ110TLCEM, TJ110TXCEM 1989
J110MLCUR, J110TLCUR, J110TXCUR 1987
J112TSLEDR, J112TSXEDR, XJ112TSLEDR, XJ112TSXEDR 1996
J112TSLEDR, J112TSXEDR, XJ112TSLEDR, XJ112TSXEDR 1996
J112TSLEOC, J112TSXEOC, XJ112TSLEOC, XJ112TSXEOC 1995
J112TSLEOC, J112TSXEOC, XJ112TSLEOC, XJ112TSXEOC 1995
J112TSLERS, J112TSXERS, XJ112TSLERS, XJ112TSXERS 1994
J112TSLERS, J112TSXERS, XJ112TSLERS, XJ112TSXERS 1994
J115JKLEOC 1995
J115JKLERS 1994
J115JLEIE, J115MLEIE, J115TLAIE, J115TLEIE, J115TXEIE, TJ115TLEIE, VJ115TLAIE, VJ115TLEIE, VJ115TXEIE 1991
J115JLEND, J115MLEND, J115TLAND, J115TLEND, J115TXEND, TJ115TLEND, VJ115TLAND 1992
J115JLEOR, J115MLEOR, J115TLEOR, J115TXAOR 1995
J115JLERC, J115MLERS, J115TLARC, J115TLERC, J115TXARS 1994
J115JLETS, J115MLETS, J115TLATS, J115TLETS, J115TXATS, TJ115TLETS, VJ115TLATS, VJ115TLETS 1993
J115MLCIH, J115MLCIM, J115TLCIH, J115TLCIM, J115TXCIH, J115TXCIM 1981
J115MLCNB, J115TLCNB, J115TXCNB 1982
J115MLCRD, J115TLCRD, J115TXCRD 1984
J115MLCSA, J115TLCSA, J115TXCSA 1980
J115MLCTE, J115TLCTE, J115TXCTE 1983
J115MLESB, J115TLASB, J115TLESB, J115TXESB, TJ115TLESB, VJ115TLASB, VJ115TLESB, VJ115TXESB 1990
J115TSLECM, J115TSXECM, XJ115HLECM, XJ115HXECM 1998
J115TSLEUA, J115TSXEUA, XJ115HLEUA, XJ115HXEUA 1997
J120TLAEM, J120TLCEM, J120TXCEM, TJ120TXCEM 1989
J120TLAIE, J120TLEIE, J120TXEIE, VJ120TLAIE, VJ120TLEIE, VJ120TXEIE 1991
J120TLAND, J120TLEND, J120TXEND, VJ120TLAND, VJ120TLEND, VJ120TXEND 1992
J120TLARC, J120TLARK, J120TLERC, J120TLERK, J120TXARC, J120TXARK, J120TXERC, J120TXERK 1994
J120TLASB, J120TLESB, J120TXESB, VJ120TLASB, VJ120TLESB, VJ120TXESB 1990
J120TLATF, J120TLATS, J120TLETF, J120TLETS, J120TXATF, J120TXATS, J120TXETF, J120TXETS, VJ120TLATF, VJ120TLATS, VJ120TLETF, VJ120TLETS, VJ120TXETF, VJ120TXETS 1993
J120TLCCA, J120TXCCA 1988
J120TLCDC, J120TXCDC 1986
J120TLCUR, J120TXCUR 1987
J125ESXENR 1992
J125ESXERK 1994
J125ESXESS 1990
J125ESXETA, J125ESXETF 1993
J125ESXW 1989
J140CXARC, J140CXARK, J140CXERE, J140CXERK, J140TLARK, J140TLARR, J140TLERK, J140TLERR, J140TXARC, J140TXARK, J140TXERK, J140TXERR 1994
J140CXATF, J140CXATS, J140CXETB, J140CXETF, J140TLATC, J140TLATF, J140TLETC, J140TLETF, J140TXATF, J140TXATS, J140TXETC, J140TXETF, VJ140TLETC, VJ140TLETF, VJ140TXETC, VJ140TXETF 1993
J140CXCCS, J140TLCCM, J140TXCCM 1988
J140CXCEC, J140TLAEB, J140TLCEB, J140TXCEB 1989
J140CXEIA, J140TLEID, J140TXEID, VJ140TLAID, VJ140TLEID, VJ140TXEID 1991
J140CXENM, J140TLANS, J140TLENS, J140TXENS, VJ140TLANS, VJ140TLENS, VJ140TXENS 1992
J140CXESR, J140TLASE, J140TLESE, J140TXESE, VJ140TLASE, VJ140TLESE, VJ140TXESE 1990
J140MLCIH, J140MLCIM, J140TLCIH, J140TLCIM, J140TXCIH, J140TXCIM 1981
J140MLCNB, J140TLCNB, J140TXCNB 1982
J140MLCSA, J140TLCSA, J140TXCSA 1980
J140MLCTE, J140TLCTE, J140TXCTE 1983
J140TLCDC, J140TXCDC 1986
J140TLCRD, J140TXCRD 1984
J140TLCUA, J140TXCUA 1987
J85MLCSA, J85TLCSA, J85TXCSA 1980
J85TTLEIE 1991
J85TTLEND 1992
J85TTLEOR 1995
J85TTLERC 1994
J85TTLETS 1993
J88MSLCCC, J90TLCCA, VJ88MSLCCC 1988
J88MSLCCC, VJ88MSLCCC 1988
J88MSLCER, J90TLAEM, J90TLCEM, TJ90TLCEM, VJ88MSLCER 1989
J88MSLCER, VJ88MSLCER 1989
J88MSLCUS 1987
J88MSLCUS 1987
J88MSLEIM 1991
J88MSLEIM, J90JLEIE, J90TLAIE, J90TLEIE, TJ90TLEIE, VJ90MLEIE, VJ90TLAIE, VJ90TLEIE 1991
J88MSLENB 1992
J88MSLENB, J90JLEND, J90TLAND, J90TLEND, TJ90TLEND, VJ90MLEND, VJ90TLAND, VJ90TLEND 1992
J88MSLEOS, J90JLEOR, J90MLEOR, J90TLEOR 1995
J88MSLEOS 1995
J88MSLERD 1994
Information:
Start By:a. remove engine oil pumpFluid Spillage Containment
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of fluids according to local regulations and mandates. 1. Check each main bearing cap (2) for its location on the engine. Each cap has an arrow (1) which points to the front of the block and a number (3) which gives the location of that cap.2. Remove No.2 through No.6 main bearing caps from the 3412 Engine and remove No.2 through No.4 main bearing caps from the 3408 Engine. Remove the lower bearings from the caps.3. Remove the thrust plates from each side of the No.4 main bearing on the 3412 Engine. Remove the thrust plates from each side of the No.3 main bearing on the 3408 Engine.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft until Tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first.
Make sure the upper and lower halves of bearings are installed so bearing tabs (5) fit into the notch in cylinder block and bearing caps.
Do not put oil on parts until the bearing clearance has been checked.5. Use Tool (A) to install the upper bearings in the block. Make sure that the end of the bearing without the tab goes into the engine block first.6. Install the lower bearings in the bearing cap. When the bearing clearance is checked and the engine is in a vertical position, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. While checking the bearing clearance, do not turn the crankshaft with the Plastigage in position.7. Check the bearing clearance with Plastigage (B) as follows: a. Put a piece of the Plastigage on the surface of the lower bearing half. b. Install the main bearing caps with arrow (6) toward the front of the cylinder block. Each cap has a number (7) on the bottom surface and must be installed in the same position as the correct number on the left side of the cylinder block.c. Put clean oil on the threads of the cap bolts. Install the cap bolts finger tight.d. Tighten the bolts on the tab end of the caps first to a torque of 258 14 N m (190 10 lb ft).e. Tighten the bolts on the other end of the caps to a torque of 258 14 N m (190 10 lb ft).
Do not use an impact wrench to tighten the bolts the additional 120 degrees.
f. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120 degrees. Tighten the bolts on the tab end of the cap 120 degrees.8. Remove the caps and measure the Plastigage. The clearance for new bearings must be 0.091 to 0.186 mm (.0036 to .0073 in). The maximum clearance for used bearings is 0.25 mm (.010 in).9. Install a thrust plate (8) (see illustration D16249) on each side of the No.4 for the 3412 Engine and No.3 for the 3408 Engine upper bearing. Install the thrust plates with the side marked "Block Side" toward the cylinder block.10. Put clean oil on the lower bearings. Repeat Steps 7b through 7f to install the bearing caps.11. Remove the No.1 and No.7 bearing caps on the 3412 Engine. Remove the No.1 and No.5 bearing caps on the 3408 Engine. Repeat Steps 4 through 8 and Step 10 for these bearings. 12. Check the crankshaft end play with Tool (C). The end play is controlled by the thrust plates on the center main bearing. Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.13 to 0.50 mm (.005 to .020 in). The maximum end play with used thrust plates is 0.89 mm (.035 in).End By:a. install engine oil pump
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "Tools And Shop Products Guide", NENG2500 for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of fluids according to local regulations and mandates. 1. Check each main bearing cap (2) for its location on the engine. Each cap has an arrow (1) which points to the front of the block and a number (3) which gives the location of that cap.2. Remove No.2 through No.6 main bearing caps from the 3412 Engine and remove No.2 through No.4 main bearing caps from the 3408 Engine. Remove the lower bearings from the caps.3. Remove the thrust plates from each side of the No.4 main bearing on the 3412 Engine. Remove the thrust plates from each side of the No.3 main bearing on the 3408 Engine.
If the crankshaft is turned in the wrong direction, the tab of the bearing will be pushed between the crankshaft and the cylinder block. This will cause damage to the crankshaft and block.
4. Turn the crankshaft until Tool (A) can be installed in oil hole (4). Turn the crankshaft in the direction which will push the upper main bearing out, tab end first.
Make sure the upper and lower halves of bearings are installed so bearing tabs (5) fit into the notch in cylinder block and bearing caps.
Do not put oil on parts until the bearing clearance has been checked.5. Use Tool (A) to install the upper bearings in the block. Make sure that the end of the bearing without the tab goes into the engine block first.6. Install the lower bearings in the bearing cap. When the bearing clearance is checked and the engine is in a vertical position, the crankshaft will have to be lifted up and held against the upper halves of the main bearings to get a correct measurement with Plastigage (B). The Plastigage will not hold the weight of the crankshaft and give a correct indication. If the engine is in a horizontal position, it is not necessary to hold the crankshaft up. While checking the bearing clearance, do not turn the crankshaft with the Plastigage in position.7. Check the bearing clearance with Plastigage (B) as follows: a. Put a piece of the Plastigage on the surface of the lower bearing half. b. Install the main bearing caps with arrow (6) toward the front of the cylinder block. Each cap has a number (7) on the bottom surface and must be installed in the same position as the correct number on the left side of the cylinder block.c. Put clean oil on the threads of the cap bolts. Install the cap bolts finger tight.d. Tighten the bolts on the tab end of the caps first to a torque of 258 14 N m (190 10 lb ft).e. Tighten the bolts on the other end of the caps to a torque of 258 14 N m (190 10 lb ft).
Do not use an impact wrench to tighten the bolts the additional 120 degrees.
f. Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120 degrees. Tighten the bolts on the tab end of the cap 120 degrees.8. Remove the caps and measure the Plastigage. The clearance for new bearings must be 0.091 to 0.186 mm (.0036 to .0073 in). The maximum clearance for used bearings is 0.25 mm (.010 in).9. Install a thrust plate (8) (see illustration D16249) on each side of the No.4 for the 3412 Engine and No.3 for the 3408 Engine upper bearing. Install the thrust plates with the side marked "Block Side" toward the cylinder block.10. Put clean oil on the lower bearings. Repeat Steps 7b through 7f to install the bearing caps.11. Remove the No.1 and No.7 bearing caps on the 3412 Engine. Remove the No.1 and No.5 bearing caps on the 3408 Engine. Repeat Steps 4 through 8 and Step 10 for these bearings. 12. Check the crankshaft end play with Tool (C). The end play is controlled by the thrust plates on the center main bearing. Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.13 to 0.50 mm (.005 to .020 in). The maximum end play with used thrust plates is 0.89 mm (.035 in).End By:a. install engine oil pump
Parts retainer JOHNSON:
0307861
0307861 RETAINER, Disc valve spring
100ESL71A, 100ESL72R, 100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78
0307857
0307857 RETAINER, Valve
100ESL71A, 100ESL72R, 100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78
0313329
0313329 RETAINER,Choke to bellcrank
100ESL71A, 100ESL72R, 100ML79S, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL7
0315104
0315104 RETAINER, Rod spark advance
100ESL71A, 100ESL72R, 100ML79S, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 50ES71S, 50ES72C, 50ES73R, 50ES74M,
0315127
0315127 RETAINER #3 IGN. LEAD
100ESL71A, 100ESL72R, 115ESL69E, 115ESL70D, 125ESL71C, 125ESL72R, 85ESL69E, 85ESL70B, 85ESL71A, 85ESL72R
0387041
0387041 RETAINER & NEEDLE SET
100ML79S, 115ML79R, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL76S, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 235TL78R, 85ML79R, BJ115ELEDR, BJ115ELEUA, BJ115GLECM, BJ115PLEEM, BJ115PLSIE, BJ115PLSSB, BJ115TLEDA, BJ130PLEED, BJ130
0323593
0323593 RETAINER, Reverse lock spring, port
100ML79S, 115ETZ78C, 115ML79R, 140ML78C, 140ML79R, 70EL78C, 70EL79R, 75ELR78C, 75ELR79R, 85ETLR78C, 85ML79R, J100MLCSC, J100WMLCDR, J100WMLCOC, J100WMLCRS, J110MLCDC, J110MLCUR, J115MLCIH, J115MLCNB, J115MLCOS, J115MLCRD, J115MLCSA, J115MLCTE, J140ML
0323594
0323594 RETAINER, Reverse lock spring, starboard
100ML79S, 115ETZ78C, 115ML79R, 140ML78C, 140ML79R, 70EL78C, 70EL79R, 75ELR78C, 75ELR79R, 85ETLR78C, 85ML79R, J100MLCSC, J100WMLCDR, J100WMLCOC, J100WMLCRS, J110MLCDC, J110MLCUR, J115MLCIH, J115MLCNB, J115MLCOS, J115MLCRD, J115MLCSA, J115MLCTE, J140ML