5031535 JOHNSON RING, GEARCASE SEAL


5031535 RING, GEARCASE SEAL JOHNSON BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC RING
5031535 RING, GEARCASE SEAL JOHNSON
Rating:
38

Buy RING, GEARCASE SEAL 5031535 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$37.57

07-11-2024
1.4330[0.64] pounds
LU: Amazon Global Store
NK 5031535 Support Steering Link
NK Cone Size [mm]: 13 || Thread Size: 14x1,5 || Quality Product
$42.60
 

09-10-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials 5031535 Tailored Heavy Duty Custom Fit Car Mats, Black with Red Trim, Premium
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Skoda Fabia (2000-2007) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Number on catalog scheme: 4
 

BRP JOHNSON entire parts catalog list:

BJ40PL4SDR, J40PL4SDE 2006
BJ40PL4SOC, J40PL4SOB 2005
BJ40PL4SRS, J40PL4SRM 2004
BJ50PL4SDR, J50PL4SDE 2006
BJ50PL4SOC, J50PL4SOB 2005
BJ50PL4SRS, J50PL4SRM 2004
J40PL4SNF 2002
J40PL4STC 2003
J50PL4SNF 2002
J50PL4STC 2003

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
ZZ 6V-9833 Cap As 2
6V-9512 Plug 2 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release". Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact the skin.Be sure that the engine and components are cool enough to touch with your bare hand prior to performing any service work.
Drain the hydraulic tank into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the hydraulic tank for the machine that is being serviced. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct draining procedure.
Illustration 1 g01100677
Remove retaining bolts (1) and open doors (1A).
Illustration 2 g01100678
Disconnect hose assemblies (2). Remove clip (3). Position hose assemblies (2) out of the way.
Remove hose assembly (6). Remove tube assemblies (4).
Disconnect hose assembly (7). Remove clip (5) and move hose assembly (7) out of the way.
Illustration 3 g01100679
Attach Tooling (A) and a suitable lifting device to fan group (9). The weight of fan group (9) is approximately 159 kg (350 lb).
Remove bolts (8). Remove fan group (9) from the machine.
Illustration 4 g01100680
Position fan group (9) on blocking. Attach a suitable lifting device to fan spider assembly (10). The weight of fan spider assembly (10) is approximately 57 kg (125 lb).
Remove bolts (11) and remove fan spider assembly (10). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Illustration 5 g01100680
Use a suitable lifting device to position fan spider assembly (10) on fan gro


Parts ring JOHNSON:

5032826
 
5032826 RING SET, PISTON
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
Back to top