5033366 JOHNSON ROD, CHOKE


5033366 ROD, CHOKE JOHNSON J4R4SRC, J4R4STS, J5R4SRC, J5R4STS ROD
5033366 ROD, CHOKE JOHNSON
Rating:
73

Buy ROD, CHOKE 5033366 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
£13.35
 

18-09-2017

SBS Automo: SBS Automotive
NK 5033366 Support Steering Link
Number on catalog scheme: 17
 

Compatible models:

BRP JOHNSON entire parts catalog list:

J4R4SRC, J4RL4SRC 2004
J4R4STS, J4RL4STS 2003
J5R4SRC, J5RL4SRC 2004
J5R4STS, J5RL4STS 2003

Information:


Illustration 1 g01023143
Typical circuit with EMCP IITest Step 1. Check for an Open Circuit in the OFF/RESET Position.
If equipped, disconnect the remote start/stop initiate contacts from the terminal strip in the customer connection box.
Disconnect the harness connector from the GSC+.
Check whether the corresponding contact of the GSC+ harness connector is the only contact that is connected to the battery negative.
Turn the ECS to the OFF/RESET position.
At the GSC+ harness connector, measure the resistance from contact "39" to the -Battery terminal of the relay module. Measure the resistance from contacts "32", "33" and "40" to the -Battery terminal. Make a note of the resistances that are measured.Expected Result:The resistance that is measured from contact "39" to the -Battery terminal of the relay module is 5 Ohms or less. The resistance that is measured from contacts "32", "33" and "40" to the -Battery terminal is greater than 5000 Ohms.Results:
OK - All resistance measurements are correct. Proceed to Test Step 2.
Not OK - The resistance measurements are not correct. The harness wiring with the incorrect resistance measurement is open or the harness wiring has failed. Repair: Repair the harness wiring or replace the harness wiring. Repair the wiring or replace the wiring between the -Battery terminal, the ECS, and the GSC+. Reconnect the remote start/stop initiate contacts after troubleshooting is complete. Stop.Test Step 2. Check for an Open Circuit in the AUTO Position.
If equipped, the remote start/stop initiate contacts will remain disconnected from the terminal strip in the customer connection box.
The harness connector remains disconnected from the GSC+.
Check whether the corresponding contact of the GSC+ harness connector is the only contact that is connected to the battery negative.
Place the ECS in the AUTO position. Measure the resistance from contact "40" of the GSC+ harness connector to the -Battery terminal of the relay module. Measure the resistance from contacts "32", "33" and "39" to the -Battery terminal. Make a note of the resistances that are measured.Expected Result:The resistance that is measured from contact "40" to the -Battery terminal of the relay module is 5 Ohms or less. The resistance that is measured from contacts "32", "33" and "39" to the -Battery terminal is greater than 5000 Ohms.Results:
OK - The resistance measurements are correct. Proceed to Test Step 3.
Not OK - The resistance measurements are not correct. The harness wiring with the incorrect resistance measurement is open or the harness wiring has failed. Repair: Repair the harness wiring or replace the harness wiring. Repair the wiring or replace the wiring between the -Battery terminal, the ECS, and the GSC+. Reconnect the remote start/stop initiate contacts after the troubleshooting is completed. Stop.Test Step 3. Check for an Open Circuit in the MAN/START Position.
If equipped, the remote start/stop initiate contacts will remain disconnected from the terminal strip in the customer connection box.
The harness connector remains disconnected from the GSC+.
Check whether the corresponding contact of the GSC+ harness connector is the only contact that is connected to the battery negative.
Place the ECS in the MAN/START position. Measure the resistance from contact "33" of the GSC+ harness connector to the -Battery terminal of the relay module. Measure the resistance from contacts "32", "39" and "40" to the -Battery terminal. Make a note of the resistances that are measured.Expected Result:The resistance that is measured from contact "33" to the -Battery terminal of the relay module is 5 Ohms or less. The resistance that is measured from contacts "32", "39" and "40" to the -Battery terminal is greater than 5000 Ohms.Results:
OK - The resistance measurements are correct. Proceed to Test Step 4.
Not OK - The resistance measurements are not correct. The harness wiring with the incorrect resistance measurement is open or the harness wiring has failed. Repair: Repair the harness wiring or replace the harness wiring. Repair the wiring or replace the wiring between the -Battery terminal, the ECS, and the GSC+. Reconnect the remote start/stop initiate contacts after the troubleshooting is completed. Stop.Test Step 4. Check for an Open Circuit in the COOLDOWN/STOP Position.
If equipped, the remote start/stop initiate contacts will remain disconnected from the terminal strip in the customer connection box.
The harness connector remains disconnected from the GSC+.
Check whether the corresponding contact of the GSC+ harness connector is the only contact that is connected to the battery negative.
Place the ECS in the COOLDOWN/STOP position. Measure the resistance from contact "32" of the GSC+ harness connector to the -Battery terminal of the relay module. Measure the resistance from contacts "33", "39" and "40" to the -Battery terminal. Make a note of the resistances that are measured.Expected Result:The resistance that is measured from contact "32" to the -Battery terminal of the relay module is 5 Ohms or less. The resistance that is measured from contacts "33", "39" and "40" to the -Battery terminal is greater than 5000 Ohms.Results:
OK - The resistance measurements are correct. Proceed to Test Step 5.
Not OK - The resistance measurements are not correct. The harness wiring with the incorrect resistance measurement is open or the harness wiring has failed.Repair: Repair the harness wiring or replace the harness wiring. Repair the wiring or replace the wiring


Parts rod JOHNSON:

5033500
 
5033500 ROD, PUSH
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
5033492
 
5033492 ROD, PUSH
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
5033393
 
5033393 ROD, CLUTCH
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
5033400
 
5033400 ROD, SHIFT (20 in. Models)
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J6R4SDC, J6R4SOS
5033399
 
5033399 ROD, SHIFT (15 in. Models)
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J6R4SDC, J6R4SOS
5033452
 
5033452 ROD, HANDLE
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
Back to top