0115494 JOHNSON SCREW, Ignition coil

Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Illustration 1 g02176881
Cut cable straps (5) and cable strap (8). Note: Note the position of cable straps and the type of cable straps.
Remove bolts (2) and bolts (10) from tube assembly (3). Remove the tube assembly from NRS exhaust cooler (6) and the cylinder head.
Remove gasket (1) (not shown) and gasket (9) (not shown).
Remove bolts (7) from tube assembly (4).
Illustration 2 g02176882
Remove bolt (12) from clip for the tube assembly.
Loosen bolts (11) for the support bracket. Remove bolts (14) and bolts (33). Remove tube assembly (15) from the NRS exhaust cooler.
Remove gasket (13) (not shown) and gasket (34) (not shown).
Remove bolts (17) and bolts (31). Remove tube assembly (16) from the NRS exhaust cooler and from the cylinder head.
Remove gasket (18) (not shown) and gasket (32) (not shown).
Remove banjo bolt (20) from tube assembly (21). Remove sealing washers (19) (not shown).
Remove bolt (25) from clip for tube assembly (21).
Remove banjo bolt (26) and remove sealing washers (27) (not shown).
Remove tube assembly (21) from the turbocharger.
Remove bolts (24) and bolts (29) from tube assembly (23).
Remove tube assembly (23). Remove gasket (22) (not shown) and gasket (30) (not shown).
Illustration 3 g02358245
Remove bolts (36) and bolts (37) from NRS exhaust cooler (6). Note: Support the weight of the NRS exhaust cooler as the bolts are removed. Note the position of different length bolts.
Remove NRS exhaust cooler (6) from the cylinder block.
Remove gasket (35) (not shown).
Illustration 4 g02176910
Remove bolts (40) from exhaust manifold (38).
Remove tube assembly (4) and remove gasket (39) (not shown). Installation Procedure
Illustration 5 g02176910
Illustration 6 g02358246
Position a new gasket (39) (not shown) onto a new tube assembly (4).
Position tube assembly (4) onto exhaust manifold (38). Install new bolts (40) and tighten the bolts ensuring that the tube assembly can still move.
Position a new gasket (35) (not shown) onto tube assembly (4).
Position NRS exhaust cooler (6) onto the cylinder block. Install bolts (36) and bolts (37) to NRS exhaust cooler (6). Hand tighten bolts (36) and bolts (37). Note: The NRS exhaust cooler should be supported as the bolts are installed.
Install new bolts (7) to tube assembly (4) and tighten bolts hand tight.
Tighten bolts (36) and bolts (37) to a torque of 44 N m (32 lb ft).
Tighten bolt (7) and bolts (40) to a torque of 22 N m (195 lb in).
Illustration 7 g02176882
Position a new gasket (18) (not shown) and a new gasket (32) (not shown) onto tube assembly (16).
Position tube assembly (16) onto the NRS exhaust cooler and the cylinder head. Install bolts (17) and bolts (31) hand tight.
Tighten bolts (17) to a torque of 22 N m (195 lb in). Tighten bolts (31) to a torque of 18 N m (159 lb in).
Ensure that tube assembly (16) is not stressed as the bolts are tightened.
Position a new gasket (13) (not shown) onto Induction mixer. Note: Ensure that the gasket is correctly installed onto location pins on the Induction mixer.
Position a new gasket (34) (not shown) onto tube assembly (15).
Position tube assembly (15) between the bracket and Induction mixer and Install bolts (14) finger tight.
Position tube assembly (15) onto the NRS exhaust cooler. Install bolts (33) finger tight.
Install bolts (12) finger tight to clip for tube assembly.
Tighten bolts (33) to a torque of 18 N m (159 lb in).
Tighten bolts (14) to a torque of 18 N m (159 lb in). Tighten bolts (11) to a torque of 44 N m (32 lb ft).
Tighten bolt (12) for clip for tube assembly to a torque of 22 N m (195 lb in).
Ensure that tube assembly (15) is not stressed as the bolts are tightened.
Remove plugs and caps from tube assemblies. Ensure that tube assembly (21) and tube assembly (23) are clean and free from damage. Replace any damaged components.
Position tube assembly (21) onto the turbocharger. Install bolt (25) to clip for tube assembly (21) finger tight.
Loosely install banjo bolt (20) and new sealing washers (19) (not shown) to tube assembly (21).
Loosely install banjo bolt (26) and new sealing washers (27) (not shown) to tube assembly (21).
Tighten banjo bolt (20) to a torque of 15 N m (133 lb in).
Tighten banjo bolt (26) to a torque of 33 N m (292 lb in).
Tighten bolt (25) to a torque of 18 N m (159 lb in).
Position a new gasket (22) (not