0304135 JOHNSON SCREW,Extension,rear 5 INCH LONGER PARTS

Active Event Codes
An active event code represents a problem with engine operation. Correct the problem as soon as possible.Active event codes are listed in ascending numerical order. The code with the lowest number is listed first.Illustration 1 is an example of the operating range of a sensor.
Illustration 1 g01365757
Example of the typical operating range of a sensor
(1) This area represents the normal operating range of the engine parameter.
(2) In these areas, the engine is operating in an unsafe operating range of the monitored parameter. An event code will be generated for the monitored parameter. The sensor circuit does not have an electronic problem.
(3) In these areas, the signal from the sensor is outside of the operating range of the sensor. The sensor circuit has an electronic problem. A diagnostic code will be generated for the sensor circuit. Refer to Troubleshooting, "Diagnostic Trouble Codes" for additional information on diagnostic codes.Logged Event Codes
When the Electronic Control Module (ECM) generates an event code, the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when an event code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeLogged events are listed in chronological order. The most recent event code is listed first.This information can be helpful for troubleshooting intermittent problems. Logged codes can also be used to review the performance of the engine.Autoclear and Clearing of Event Codes
A non-critical event code is cleared from memory when one of the following conditions occur:
The code does not recur for 100 service hour meter hours.
A new code is logged and there are already 30 codes in memory. In this case, the oldest code is cleared.
The service technician manually clears the code.Always clear logged event codes after investigating and correcting the problem which generated the code.Critical Event Codes
Critical event codes that are critical to engine life will not automatically clear and are only cleared from memory when one of the following conditions occur:
A new code is logged and there are already 30 codes in memory. In this case, the oldest code is cleared.
The service technician manually clears the code.Note: Examples of critical event codes include "Engine Over Speed", "Low Oil Pressure", "High Intake Temperature" and "High Coolant Temperature".Always clear logged event codes after investigating and correcting the problem which generated the code.Troubleshooting
For basic troubleshooting of the engine, perform the following steps in order to diagnose a malfunction:
Obtain the following information about the complaint:
The event and the time of the event
Determine the conditions for the event. The conditions will include the engine rpm and the load.
Determine if there are any systems that were installed by the dealer or by the customer that could cause the event.
Determine whether any additional events occurred.
Verify that the complaint is not due to normal engine operation. Verify that the complaint is not due to error of the operator.
Narrow the probable cause. Consider the operator information, the conditions of operation, and the history of the engine.
Perform a visual inspection. Inspect the following items:
Fuel supply
Oil level
Oil supply
Wiring
ConnectorsBe sure to check the connectors. Connector inspection is important for problems that are intermittent. Refer to Troubleshooting, "Electrical Connectors - Inspect".If these steps do not resolve the problem, refer to Table 1 for the procedure to troubleshoot the event code.Cross-Reference Information for Event Codes
Table 1 is a list of the event codes for the engine. The event codes are cross-referenced with the appropriate procedure that can be used to troubleshoot the code.Event codes are generated when abnormal operating conditions exist.Note: A requirement for all troubleshooting is that the troubleshooting is based on active and/or passive diagnostic trouble codes. Do not troubleshoot based on flash codes alone.
Table 1
Diagnostic Trouble Codes
J1939 Code and Description CDL Code and Description Troubleshooting Procedure Flash Codes
94-16
Engine Fuel Delivery Pressure : High - moderate severity (2) E1218 (2)
High Unfiltered Fuel Pressure Troubleshooting, "Fuel Pressure Is High" N/A
100-17
Engine Oil Pressure : Low - least severe (1) E360 (1)
Low Engine Oil Pressure Troubleshooting, "Oil Pressure Is Low" 157
100-18
Engine Oil Pressure : Low - moderate severity (2) E360 (2)
Low Engine Oil Pressure Troubleshooting, "Oil Pressure Is Low" 157
100-1
Engine Oil Pressure : Low - most severe (3) E360 (3)
Low Engine Oil Pressure Troubleshooting, "Oil Pressure Is Low" 157
101-15
Engine Crankcase Pressure : High - least severe (1) E1036 (1)
High Crankcase Pressure Troubleshooting, "Crankcase Pressure Is High" N/A
101-16
Engine Crankcase Pressure : High - moderate severity (2) E1036 (2)
High Crankcase Pressure Troubleshooting, "Crankcase Pressure Is High" N/A
102-1
Engine Intake Manifold #1 Pressure : Low - most severe (3) E1045 (3)
Low Intake Manifold Pressure Troubleshooting, "Intake Manifold Air Pressure Is Low" NO
102-18
Engine Intake Manifold #1 Pressure : Low - moderate severity (2) E1045 (2)
Low Intake Manifold Pressure Troubleshooting, "Intake Manifold Air Pressure Is Low" 135
105-15
Engine Intake Manifold #1 Temperature : High - least severe (1) E539 (1)
High Intake Manifold Air Temperature Troubleshooting, "Intake Manifold Air Temperature Is High" 133
105-16
Engine Intake Manifold #1 Temperature : High - moderate severity (2) E539 (2)
High Intake Manifold Air Temperature Troubleshooting, "Intake Manifold Air Temperature Is High"