0317926 SCREW, C' case to cyl.-2-1/4" long JOHNSON
100ESL72R, 115ESL73M, 125ESL72R, 135ESL73M, 85ESL72R, 85ESL73M
SCREW
Price: query
Rating:
BRP JOHNSON entire parts catalog list:
- CYLINDER & CRANKCASE » 0317926
125ESL72R 1972
135ESL73M 1973
85ESL72R 1972
85ESL73M 1973
Information:
Alternator
Condition of the alternator drive belts
Electrical operation of the alternator
Condition of the alternator bearings
Condition of the alternator drive pulleyCharging Circuit
Inspection of the charging circuit
Condition of the batteriesRecommended Actions
Note: The procedures have been listed in order of probability. Complete the following procedures in the order that is provided.Condition of the Alternator Drive Belts
Inspect the condition of the alternator drive belts. If the alternator drive belts are worn or damaged, replace the belts. Refer to Disassembly and Assembly for the correct procedure.
Check the belt tension. If the engine is equipped with an automatic belt tensioner, check the automatic belt tensioner. If necessary, replace the automatic belt tensioner. Refer to Disassembly and Assembly for the correct procedure. Note: Excessive belt tension may result in damage to the alternator.Electrical Operation of the Alternator
Verify the electrical operation of the alternator.
Use a battery tester to verify that the batteries are fully charged. If the condition of the batteries is suspect, perform a load test in order to ensure that the batteries are ok. If necessary, replace the batteries.
Install a 225-8266 Ammeter Tool Gp to the engine's battery cable.
Measure the current draw while the engine is not running.
While the engine is not running, apply a load to the electrical system. If equipped, use engine accessories such as headlights or a blower motor to load the electrical system.
Record the meter reading. Record the orientation of the meter installation. Note: Ensure that you record the orientation of the meter installation. Be sure to record a positive current draw or a negative current draw for the electrical system.
Remove the load from the electrical system.
Confirm that the alternator is applying current to the engine's electrical system.
Start the engine.
Apply a strong load to the electrical system. If equipped, use loads such as headlights, auxiliary lighting, and the heater's blower motor.
Again, record the meter reading. Record the orientation of the meter installation. Note: Ensure that you record the orientation of the meter installation. Be sure to record a positive current draw or a negative current draw for the electrical system.
Remove the load from the electrical system and shut down the engine.
Compare the current readings that are recorded. Determine if the current flow had changed from a state of discharge to a state of charge. If the ammeter readings indicate that the electrical system changed from a state of discharge to a state of charge, the alternator is operating correctly.If the ammeter readings indicate that the system remained in a state of discharge during the test, the alternator may need to be replaced.For additional testing procedures, refer to Special Instruction, REHS0354, "Charging System Troubleshooting". Repair the alternator or replace the alternator, as needed.Condition of the Alternator Bearings
Check the alternator bearings for signs of wear. Repair the alternator or replace the alternator, as needed. Refer to Disassembly and Assembly for the correct procedure.Condition of the Alternator Drive Pulley
Check the condition of the alternator drive pulley. If there is excessive wear, replace the pulley. Check that the nut for the pulley has not become loose. If necessary, tighten the nut to the proper torque specification. Refer to Disassembly and Assembly for the correct procedure.Check the alignment of the alternator's drive pulley with the other pulleys that are in the drive system. Correct the alignment of the pulley, if necessary.Inspection of the Charging Circuit
Inspect the battery cables, wiring, and connections in the charging circuit. Clean all connections and tighten all connections. Replace any faulty parts.Condition of the Batteries
Check the charge on the engine's batteries. Charge the batteries, if necessary. Refer to Special Instruction, SEHS7633, "Battery Test Procedure" for the proper testing procedure.Load test the batteries. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries".
Condition of the alternator drive belts
Electrical operation of the alternator
Condition of the alternator bearings
Condition of the alternator drive pulleyCharging Circuit
Inspection of the charging circuit
Condition of the batteriesRecommended Actions
Note: The procedures have been listed in order of probability. Complete the following procedures in the order that is provided.Condition of the Alternator Drive Belts
Inspect the condition of the alternator drive belts. If the alternator drive belts are worn or damaged, replace the belts. Refer to Disassembly and Assembly for the correct procedure.
Check the belt tension. If the engine is equipped with an automatic belt tensioner, check the automatic belt tensioner. If necessary, replace the automatic belt tensioner. Refer to Disassembly and Assembly for the correct procedure. Note: Excessive belt tension may result in damage to the alternator.Electrical Operation of the Alternator
Verify the electrical operation of the alternator.
Use a battery tester to verify that the batteries are fully charged. If the condition of the batteries is suspect, perform a load test in order to ensure that the batteries are ok. If necessary, replace the batteries.
Install a 225-8266 Ammeter Tool Gp to the engine's battery cable.
Measure the current draw while the engine is not running.
While the engine is not running, apply a load to the electrical system. If equipped, use engine accessories such as headlights or a blower motor to load the electrical system.
Record the meter reading. Record the orientation of the meter installation. Note: Ensure that you record the orientation of the meter installation. Be sure to record a positive current draw or a negative current draw for the electrical system.
Remove the load from the electrical system.
Confirm that the alternator is applying current to the engine's electrical system.
Start the engine.
Apply a strong load to the electrical system. If equipped, use loads such as headlights, auxiliary lighting, and the heater's blower motor.
Again, record the meter reading. Record the orientation of the meter installation. Note: Ensure that you record the orientation of the meter installation. Be sure to record a positive current draw or a negative current draw for the electrical system.
Remove the load from the electrical system and shut down the engine.
Compare the current readings that are recorded. Determine if the current flow had changed from a state of discharge to a state of charge. If the ammeter readings indicate that the electrical system changed from a state of discharge to a state of charge, the alternator is operating correctly.If the ammeter readings indicate that the system remained in a state of discharge during the test, the alternator may need to be replaced.For additional testing procedures, refer to Special Instruction, REHS0354, "Charging System Troubleshooting". Repair the alternator or replace the alternator, as needed.Condition of the Alternator Bearings
Check the alternator bearings for signs of wear. Repair the alternator or replace the alternator, as needed. Refer to Disassembly and Assembly for the correct procedure.Condition of the Alternator Drive Pulley
Check the condition of the alternator drive pulley. If there is excessive wear, replace the pulley. Check that the nut for the pulley has not become loose. If necessary, tighten the nut to the proper torque specification. Refer to Disassembly and Assembly for the correct procedure.Check the alignment of the alternator's drive pulley with the other pulleys that are in the drive system. Correct the alignment of the pulley, if necessary.Inspection of the Charging Circuit
Inspect the battery cables, wiring, and connections in the charging circuit. Clean all connections and tighten all connections. Replace any faulty parts.Condition of the Batteries
Check the charge on the engine's batteries. Charge the batteries, if necessary. Refer to Special Instruction, SEHS7633, "Battery Test Procedure" for the proper testing procedure.Load test the batteries. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries".
Parts screw JOHNSON:
0306559
0306559 SCREW,Ignition switch
100ESL71A, 100ESL72R, 100ML79S, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL7
0304607
0304607 SCREW, Rectifier and amplifier to bracket
100ESL71A, 100ESL72R, 115ESL69E, 115ESL70D, 125ESL71C, 125ESL72R, 50ES71S, 50ES72C, 55ES69A, 85ESL69E, 85ESL70B, 85ESL71A, 85ESL72R, TR-10R, V4A-20A, V4S-20A, V4T-14B, VX-14B
0305513
0305513 SCREW, Throttle lever
100ESL71A, 100ESL72R, 115ESL69E, 115ESL70D, 125ESL71C, 125ESL72R, 40E71B, 50ES71S, 50ES75B, 50R79C, 55E76E, 55E77D, 55E78S, 55E79C, 55ES69A, 60ES71C, 65ES72S, 85ESL69E, 85ESL70B, 85ESL71A, 85ESL72R, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25PL3EEM, BJ25PL
0313075
0313075 SCREW,Valve to shaft
100ESL71A, 100ESL72R, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 175TL77S, 200TL76S, 200TL77C, 85EL76D, 85EL77S, 85ESL69E, 85ESL70B, 85ESL71A, 85ESL72R,
0311840
0311840 SCREW, Rubber mount
100ESL71A, 100ESL72R, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 85EL76D, 85EL77S, 85ESL69E, 85ESL70B, 85ESL71A, 85ESL72R, 85ESL73M, 85ESL74B, 85ESL75E
0302873
0302873 SCREW, Impeller housing
100ESL71A, 100ESL72R, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 150TL78S, 175TL77S, 175TL78C, 200TL76S, 200TL77C, 200TL78R, 235TL78R, 85EL76D, 85EL77S,
0315383
0315383 SCREW, Front hook to locating bracket
100ESL71A, 100ESL72R, 115ESL69E, 115ESL73M, 125ESL71C, 125ESL72R, 135ESL73M, 85ESL69E, 85ESL70B, 85ESL71A, 85ESL72R, 85ESL73M
0315405
0315405 SCREW, Crankcase to cyl.
100ESL71A, 100ESL72R, 115ESL69E, 115ESL70D, 115ESL73M, 125ESL71C, 125ESL72R, 135ESL73M, 85ESL69E, 85ESL70B, 85ESL71A, 85ESL72R, 85ESL73M