0333278 JOHNSON SCREW, Gearcase to hsg., rear


0333278 SCREW, Gearcase to hsg., rear JOHNSON J105WRLEES, J105WRLSIF, J105WRLSSC, SJ105RWLH, SJ105RWLH, SJ105RWLP, SJ105RWLP, SJ125RWYJ, SJ125RWYN, SJ125RWYV SCREW
0333278 SCREW, Gearcase to hsg., rear JOHNSON
Rating:
23

Buy SCREW, Gearcase to hsg., rear 0333278 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 66
 

BRP JOHNSON entire parts catalog list:

J105WRLEES, J105WRYEES 1999
J105WRLSIF, J105WRYSIF 2001
J105WRLSSC, J105WRYSSC 2000
SJ105RWLH, SJ105RWYH 1998
SJ105RWLH, SJ105RWYH 1998
SJ105RWLP, SJ105RWYP 1997
SJ105RWLP, SJ105RWYP 1997
SJ125RWYJ 1997
SJ125RWYN 1998
SJ125RWYV 1996

Information:


This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.Valve Lash Check
An adjustment is NOT NECESSARY if the measurement of the valve lash is in the acceptable range. Check the valve lash while the engine is stopped. The range is specified in Table 1.
Table 1
Valve Lash
Valves Acceptable Range for Valve Lash
Inlet 0.38 0.08 mm (0.015 0.003 inch)
Exhaust 0.76 .08 mm (0.030 0.003 inch) If the measurement is not within this range adjustment is necessary. Refer to Testing And Adjusting, "Valve Lash Adjustment".Valve Lash Adjustment
Illustration 1 g00561261
(A) Inlet valves
(B) Exhaust valves
(C) Left side of the engine
(D) Cylinder number
(E) Front of the engine
(F) Right side of the engine
(G) Flywheel end of the engine
Illustration 2 g00506544
(1) Valve adjustment locknut
(2) Exhaust adjustment screw
(3) Valve adjustment locknut
(4) Inlet adjustment screw
(5) Feeler gauge
Table 2
Valve Lash
Valves Gauge Dimension
Inlet 0.38 mm (0.015 inch)
Exhaust 0.76 mm (0.030 inch) Adjust the valve lash while the engine is stopped. Use the following procedure in order to adjust the valves:
Put the No. 1 piston at the top center position. Note: If the engine is equipped with an engine compression brake, loosen the adjusting screw for the lash on the slave piston for the compression brake prior to adjusting the engine valve lash. Refer to the Testing and Adjusting, "Slave Piston Lash - Adjust" topic in order to adjust the slave piston lash.Note: See Testing and Adjusting, "Finding Top Center Position for the No. 1 Piston" for further details.
With No. 1 piston at the top center position of the compression stroke, an adjustment can be made to the valves. Before any adjustments are made, lightly tap each rocker arm at the top of the adjustment screw. Use a soft mallet to ensure that the lifter roller seats against the camshaft's base circle.
Make an adjustment to the valve lash on the inlet valves for cylinders 1, 2, and 4.
Loosen valve adjustment locknut (3).
Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (3) while valve adjustment screw (4) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Make an adjustment to the valve lash on the exhaust valves for cylinders 1, 3, and 5.
Loosen valve adjustment locknut (1).
Place the appropriate feeler gauge (5) between the exhaust rocker arm and the exhaust valve bridge. Turn exhaust adjustment screw (2) while valve adjustment locknut (1) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (1) while valve adjustment screw (2) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Remove the timing bolt, and turn the flywheel by 360 degrees in the direction of engine rotation. This will position the No. 6 piston at the top center on the compression stroke. Install the timing bolt in the flywheel.
Make an adjustment to the valve lash on the inlet valves 3, 5, and 6.
Loosen valve adjustment locknut (3).
Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (3) while valve adjustment screw (4) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Make an adjustment to the valve lash on the exhaust valves 2, 4, and 6.
Loosen valve adjustment locknut (1).
Place the appropriate feeler gauge (5) between the exhaust rocker arm and the exhaust valve bridge. Turn exhaust adjustment screw (2) while valve adjustment locknut (1) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 2.
After each adjustment, tighten valve adjustment locknut (1) while valve adjustment screw (2) is being held from turning. Tighten to a torque of 30 7 N m (22 5 lb ft). Recheck each adjustment.
Remove the timing bolt from the flywheel after all valve lash adjustments have been made. Refer to the Testing and Adjusting, "Slave Piston Lash - Adjust" topic for information on adjusting the slave piston lash.Note: The valve lash must be adjusted before you adjust the compression brake.The lash must also be adjusted on the electronic unit injector. Refer to Testing and Adjusting, "Electronic Unit Injector - Adjust" for more information.


Parts screw JOHNSON:

0306049
 
0306049 SCREW,Cylinder head
100ML79S, 10E74G, 10E75C, 10E76G, 115EL77S, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 15E74G, 15E75C, 15E76A, 175TL77S, 175TL78C, 175TL79R, 200T
0306500
 
0306500 SCREW,Tube to powerhead
BJ10EEDD, BJ10RELEUS, BJ115ELEDR, BJ115ELEUA, BJ115GLECM, BJ115PLEEM, BJ115PLSIE, BJ115PLSSB, BJ150ELECD, BJ150ELEDB, BJ150ELEUC, BJ15EEDS, BJ15RELEUC, BJ175EXECD, BJ175EXEDB, BJ175EXEUC, BJ175PLEES, BJ200CXEDR, BJ90ELEDR, BJ90ELEUA, BJ90PLEEB, BJ90P
0319886
 
0319886 SCREW, Retainer to plate
100ML79S, 115EL77S, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL76S, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 235TL78R, 50ES75B, 50R79
0327768
 
0327768 SCREW, Actuator cam to lever
AM55RSLD, BJ40EECR, BJ40EEDS, BJ40EEEA, BJ40EEUC, BJ40ELSIF, BJ40ELSSM, BJ50BEEDS, BJ50EEER, BJ50ELSIF, BJ50ELSSA, BJ50ESECC, BJ50RLEUC, HJ25FPO, HJ25FPV, HJ45RCLEDS, HJ45RCLEUC, HJ55RSLC, HJ55RSLW, J105WELEEN, J105WELSIF, J105WELSSC, J105WRLEES, J10
0328714
 
0328714 SCREW,Throttle lever
AM55RSLD, BJ115ELEDR, BJ115ELEUA, BJ115GLECM, BJ115PLEEM, BJ115PLSIE, BJ115PLSSB, BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, BJ135PLSIF, BJ150ELECD, BJ150ELEDB, BJ150ELEUC, BJ175EXECD, BJ175EXEDB, BJ175EXEUC, BJ175PLEES, BJ175PLSIF,
0328694
SCREW, Front to rear cover
0328694 SCREW, Front to rear cover
AM55RSLD, BJ115ELEDR, BJ115TLEDA, BJ150ELECD, BJ150ELEDB, BJ150ELEUC, BJ175EXECD, BJ175EXEDB, BJ175EXEUC, BJ175PLEES, BJ175PLSIF, BJ175PLSSC, BJ200CXEDR, BJ200CXEEB, BJ200CXSSE, BJ200PLSIF, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20S
0330838
 
0330838 SCREW, Air silencer cover to base
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, BJ135PLSIF, BJ15EEDS, BJ15RELEUC, BJ200CXEDR, BJ200CXEEB, BJ20SEECB, BJ20SEEUM, BJ20SRECB, BJ20SRE
0908158
 
0908158 SCREW, Guide to hsg.
AM55RSLD, BJ115ELEDR, BJ115ELEUA, BJ115GLECM, BJ115PLEEM, BJ115PLSIE, BJ115PLSSB, BJ115TLEDA, BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, BJ135PLSIF, BJ150ELECD, BJ150ELEDB, BJ150ELEUC, BJ175EXECD, BJ175EXEDB, BJ175EXEUC, BJ175PLEES,
Back to top