0338232 JOHNSON SCREW, Cover, rear, upper


0338232 SCREW, Cover, rear, upper JOHNSON BJ10EEDD, BJ15EEDS, HJ15KCLN, J10EEOE, J10EERB, J10EETM, J15EEOD, J15EERE, J15EETB, SJ10REDD, SJ10RPB SCREW
0338232 SCREW, Cover, rear, upper JOHNSON
Rating:
93

Buy SCREW, Cover, rear, upper 0338232 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 25
 

BRP JOHNSON entire parts catalog list:

BJ10EEDD, BJ10ELEDD, BJ10REDD, BJ10RELEDD, BJ10RLEDD, BJ10SELEDD, J10EEDD, J10ELEDD, J10REDD, J10RELEDD, J10RLEDD, J10SELEDD 1996
BJ15EEDS, BJ15ELEDS, BJ15REDS, BJ15RLEDS, J15EEDS, J15ELEDS, J15REDS, J15RELEDS, J15RLEDS, SJ15BAEDC, SJ15REDS, SJ15RLEDS 1996
HJ15KCLN, HJ15KCN, SJ15RPG, SJ15RPLG 1996
J10EEOE, J10ELEOE, J10RELEOE, J10REOE, J10RLEOE, J10SELEOE 1995
J10EERB, J10ELERB, J10RELERB, J10RERB, J10RLERB, J10SELERB 1994
J10EETM, J10ELETM, J10RELETM, J10RETM, J10RLETM, J10SELETM, TJ10RELETM 1993
J15EEOD, J15ELEOD, J15RELEOD, J15REOD, J15RLEOD 1995
J15EERE, J15ELERE, J15RELERE, J15RERE, J15RLERE 1994
J15EETB, J15ELETB, J15RELETB, J15RETB, J15RLETB 1993
SJ10REDD, SJ10RLEDD, SJ10SELEDD 1996
SJ10RPB, SJ10RPLB 1996

Information:

1. Remove nuts (1), and move clip (2) and the hose away from cover (3).2. Remove cover (3) and the gasket. 3. Remove the bolts that hold cover (4) to the ring, and remove the cover. 4. Remove the four bolts and ring (5). 5. Remove gear (7) from the front of fuel injection pump camshaft (6).Install Fuel Injection Pump And Governor Drive
1. Remove the plug from the timing pin hole, and put tool (A) in the timing pin hole.2. Install two 7.16" × 20 NF × 4" long bolts in fuel injection pump camshaft (1). Slowly, rotate the fuel injection pump camshaft until tool (A) goes into the groove in the fuel injection pump camshaft. Remove the bolts. 3. Put No. 1 piston at the top center compression position (TDC) with the following procedure.a. Remove the plug and cover from the left side of the flywheel housing, and install tool (B) in the flywheel housing.b. Use tool (B) to slowly rotate the engine in the direction of normal rotation, (counterclockwise as seen from the flywheel end of the engine), until timing bolt (2), [the long bolt that holds the cover to the flywheel housing,] can be installed in the flywheel housing and into the hole in the flywheel. c. Remove the valve cover from the valve cover base. Check to see if both rocker arms (3) for the No. 1 cylinder can be moved backward and forward. The No. 1 piston is at the top center compression stroke when the timing bolt is installed in the flywheel and both rocker arms for the No. 1 cylinder can be moved backward and forward. If both rocker arms can not be moved, the No. 1 piston is not at the top compression position. Remove the bolt from the flywheel and rotate the engine in the direction of normal rotation (counterclockwise as seen from the flywheelend of the engine) one full turn (360°), and install the timing bolt again.4. Remove the timing bolt and rotate the engine opposite the direction of normal rotation (clockwise as seen from the flywheel end of the engine for a minimum of 30 degrees). 5. Put gear (4) in position on the fuel injection pump camshaft. 6. Put ring (5) in position on the fuel injection pump camshaft and install the four bolts that hold it. Tighten the bolts to a torque of 3 N m (27 lb.in.).7. Use tool (B) and slowly rotate the engine in the direction of normal rotation until the timing bolt can be installed in the flywheel.8. Tighten the bolt that holds ring (5) to the fuel injection pump camshaft to a torque of 55 7 N m (41 5 lb.ft.).9. Remove tool (A) from the fuel injection pump, and the timing bolt from the flywheel.10. Check the timing as follows:a. Rotate the engine in the direction of normal rotation (counterclockwise as seen from the flywheel end of the engine) two full turns, and install tool (A) and the timing bolt again.b. The timing is correct if tool (A) and the timing bolt can be installed at the same time. The timing procedure must be done again if the timing bolt and tool (A) can not be installed at the same time.c. Remove tool (A), and install the plug in the fuel injection pump housing. Remove the timing bolt and tool (B), and install the cover and plug in the flywheel housing. 11. Put O-ring seals (7) on cover (6). Put clean engine oil on the O-ring seals.12. Install cover (6) on the ring, and install the bolts that hold it. 13. Put the gasket and cover (8) in position on the timing cover. Put the hose and clip (9) in position, and install the bolts that hold the cover and clip to the timing cover.


Parts screw JOHNSON:

0306049
 
0306049 SCREW,Cylinder head
100ML79S, 10E74G, 10E75C, 10E76G, 115EL77S, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 15E74G, 15E75C, 15E76A, 175TL77S, 175TL78C, 175TL79R, 200T
0306643
 
0306643 SCREW, Cover to impeller
100ESL71A, 100ESL72R, 100ML79S, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79
0316134
 
0316134 SCREW,Retainer
50ES71S, 50ES72C, 50ES73R, 50R79C, 55E79C, AM55RSLD, BJ10EEDD, BJ10RELEUS, BJ15EEDS, BJ15RELEUC, HJ45RCLEDS, HJ45RCLEUC, HJ55RSLC, HJ55RSLW, J10EECC, J10EEOE, J10EERB, J10EETM, J10ELEER, J10ELSIM, J10ELSSA, J15EECR, J15EEOD, J15EERE, J15EETB, J15ELEE
0319227
 
0319227 SCREW,Tilt knob
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 25E78C, 25E79R, 35E76G, 35E78R, 35E79A, BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSR
0327888
 
0327888 SCREW
D25RWA, J100STLCCA, J100STLCEM, J100STLEIE, J100STLEND, J100STLESB, J100STLETS, J10ECCD, J10ECDB, J10ECES, J10EEIR, J10EEOE, J10EERB, J10EESC, J10EETM, J110MLCCA, J110MLCDC, J110MLCEM, J110MLCUR, J115JLEIE, J115JLEND, J115JLETS, J115MLESB, J120TLAEM,
0330346
 
0330346 SCREW, Cam follower adjust.
BJ10EEDD, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15RELEUC, BJ3REDS, BJ4BREDS, BJ4BREUC, BJ4RDHEDS, BJ5DREDS, BJ5DREUC, BJ6DRECR, BJ6DREDS, BJ6DREUC, BJ8RCB, BJ8RCH, BJ8RCLT, BJ8REDS, HJ15KCF, HJ15KCLN, HJ15KCLO, J10EC
0908045
 
0908045 SCREW
AM55RSLD, BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ15RELEUC, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, B
0125529
 
0125529 SCREW, Housing to tank
BJ10EEDD, BJ10FAEDC, BJ10FDLEDR, BJ15EEDS, BJ15FAEDR, BJ20SEEDA, BJ20SREDA, BJ25BAEDR, BJ25EEDM, BJ30BAEDE, BJ30EEDE, BJ40EEDS, BJ50BEEDS, BJ50DTLEDC, BJ5FRBEUS, BJ60ELEDR, BJ70ELEDA, BJ8FRBEDC, HJ15KCF, HJ15KCLN, HJ15KCLO, HJ20CREDA, HJ25FPO, HJ25RL
Back to top