0446068 SCREW, Intake to cylinder head JOHNSON
BJ10FAEDC, BJ10FAEUR, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, J8R4SRC, J8R4STS
SCREW
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- CYLINDER & CRANKCASE » 0446068
BJ8FRBECA, BJ8FRBLECA, J8FRECA, J8FRLECA, J8FRXECA 1998
BJ8FRBEDC, BJ8FRBLEDC, BJ8FRBXEDC, HJ8FREDC, HJ8FRLEDC, J8FREDC, J8FRXEDC 1996
BJ8FRBEUR, BJ8FRBLEUR, BJ8FRBXEUR, HJ8FREUR, HJ8FRLEUR, J8FREUR, J8FRXEUR 1997
HJ10FELECA, J10FOECA, J10FOLECA 1998
J8R4SRC, J8RL4SRC 2004
J8R4STS, J8RL4STS 2003
Information:
Illustration 1 g01246547
Schematic
Illustration 2 g01112632
(P1-48) +Battery
(P1-52) +Battery
(P1-53 (if applicable)) +Battery
(P1-61) −Battery
(P1-63) −Battery
(P1-65 (if applicable)) −Battery
(P1-70) Keyswitch Test Step 1. Inspect Electrical Connectors and Wiring
Turn the battery disconnect switch to the OFF position.
Turn the keyswitch to the OFF position.
Thoroughly inspect the ECM connectors J1/P1 and J2/P2. Inspect all of the J61/P61 machine connector. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Check the harness and the wiring for abrasion and for pinch points. Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points. All connections and grounds are tight and free of corrosion.Results:
OK - The harness and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Battery Voltage at the ECM
Turn the battery disconnect switch to the ON position.
Disconnect the J1/P1 ECM connector.
Turn the keyswitch to the ON position.
Measure the voltage between P1-48 (Unswitched Positive Battery) and P1-61 (Negative Battery).
Measure the voltage between P1-52 (Unswitched Positive Battery) and P1-63 (Negative Battery).
Measure the voltage between P1-53 (Unswitched Positive Battery) and P1-65 (Negative Battery).
Measure the voltage between P1-70 (Keyswitch) and P1-63 (Negative Battery). Expected Result:The measured voltage is between 22.0 VDC and 27.0 VDC.Results:
OK - The ECM is receiving the correct voltage.Repair: If an intermittent condition is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - The voltage is not correct at the ECM. Proceed to Test Step 3.
Keyswitch voltage out of range - Proceed to Test Step 4.Test Step 3. Check the Batteries
Measure the no-load battery voltage at the battery posts.
Load test the batteries. Use the 4C-4911 Battery Load Tester. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries" and Special Instruction, SEHS7633, "Battery Test Procedure". Expected Result:The batteries pass the load test. The measured voltage is the minimum specification for a 12V or 24V system.Results:
OK - The batteries are OK.Repair: There is an open circuit or excessive resistance in the wiring or connections between the batteries and the ECM. Verify that the 20 Amp fuse for the ECM is not blown. Check the connections at the J61/P61 machine connector. Verify that the connection for the engine ground is clean and tight and that the battery disconnect switch is functioning properly. Repair the connectors or wiring and/or replace the connectors or wiring.STOP
Not OK - The battery voltage is low or the battery did not pass the load test.Repair: Recharge or replace the faulty batteries. Verify that the repair eliminates the problem.STOPTest Step 4. Check the Voltage from the Keyswitch to the ECM
Turn the keyswitch to the OFF position.
Remove the wire from the terminal R of the keyswitch.
Turn the keyswitch to the ON position.
Measure the voltage on terminal B of the keyswitch to engine ground.
Measure the voltage on terminal R of the keyswitch to engine ground.
Turn the keyswitch to the OFF position. Expected Result:Voltage is present on terminal B and terminal R at the keyswitch.Results:
OK - Voltage is present on terminal B and terminal R at the keyswitch.Repair: If voltage is present on terminal R, repair the wire between the keyswitch and the ECM. Verify that the problem is eliminated.STOP
Not OK - Voltage is not present on terminal B at the keyswitch.Repair: If voltage is not present on terminal B, repair the wire between the +Battery and the keyswitch. Verify that the fuse for the keyswitch is not blown. Verify that the problem is eliminated.STOP
Not OK - Voltage is not present on terminal R at the keyswitch.Repair: If voltage is present on terminal B of the keyswitch but not present on terminal R, replace the keyswitch. Return all wiring to the original configuration. Verify that the problem is eliminated.STOP
Parts screw JOHNSON:
0304024
0304024 SCREW
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 25R69B, 25R70C, 25R71S, 33E69A, 33E69A, 33E70M, 33E70M, 35E76G, 3
0319227
0319227 SCREW,Tilt knob
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 25E78C, 25E79R, 35E76G, 35E78R, 35E79A, BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSR
0908045
0908045 SCREW
AM55RSLD, BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ15RELEUC, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, B
0339043
0339043 SCREW, Spindle
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15RELEUC, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25PL3EEM, BJ25PL3SIE, BJ25PL3SSB, BJ35ARECR, BJ35AREDS, BJ35AREEA, BJ35AREUC, BJ35E3SIE, BJ35E3SSB, B
0341206
0341206 SCREW, Gearcase to exh. hsg.
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ15RELEUC, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, HJ15KCF, HJ15KCLN, HJ
0341474
0341474 SCREW, Cover to body
BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25PL3EEM, BJ25PL3SIE, BJ25PL3SSB, BJ35ARECR, BJ35AREDS, BJ35AREEA, BJ35AREUC, BJ35E3SIE, BJ35E3SSB, BJ5FRBECC, BJ5FRBEUS, B
0446061
0446061 SCREW, Rod cap
BJ10FAEDC, BJ10FAEUR, BJ5FRBECC, BJ5FRBEUS, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, HJ6FRECA, HJ6FREUR, J6R4SRC, J6R4STS, J8R4SRC, J8R4STS
0446017
0446017 SCREW, Cylinder valve adjustment
BJ10FAEDC, BJ10FAEUR, BJ5FRBECC, BJ5FRBEUS, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, HJ6FRECA, HJ6FREUR, J6R4SRC, J6R4STS, J8R4SRC, J8R4STS