0330694 JOHNSON SEAL, Engine cover


0330694 SEAL, Engine cover JOHNSON CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA SEAL
0330694 SEAL, Engine cover JOHNSON
Rating:
23

Buy SEAL, Engine cover 0330694 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

BRP JOHNSON entire parts catalog list:

CJ275TLCDC, CJ275TXCDC, J275PTLCDC, J275PTXCDC 1986
CJ275TLCOS, CJ275TXCOS, J275TLCOS, J275TXCOS 1985
CJ300TLCDC, CJ300TXCDC, J300TLCDC, J300TXCDC 1986
CJ300TLCOS, CJ300TXCOS, J300TLCOS, J300TXCOS 1985
J275CLCUR, J275CXCUR, J275PLCUR, J275PXCUR 1987
J275CXCCA, J275PLCCA, J275PXCCA 1988
J300CLCUR, J300CXCUR, J300PLCUR, J300PXCUR 1987
J300CXCCA, J300PLCCA, J300PXCCA 1988

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1 Start By:
If necessary, remove the secondary fuel filter and the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install" for the correct procedure.
If necessary, remove the water separator and fuel filter (Primary). Refer to Disassembly and Assembly, "Water Separator and Fuel Filter (Primary) - Remove and Install" for the correct procedure.
Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install" for the correct procedure.
Remove the crankcase breather canister and plastic tube assemblies. Refer to Disassembly and Assembly, "Crankcase Breather - Remove" for the correct procedure.
Remove the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) - Remove and Install" for the correct procedure.
Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" for the correct procedure.
Remove the mounting bracket for the electronic control module. Refer to Disassembly and Assembly, "ECM Mounting Bracket - Remove and Install" for the correct procedure.
Remove the glow plugs. Refer to Disassembly and Assembly, "Glow Plugs - Remove and Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
Illustration 1 g02005213
Disconnect the upper radiator hose from water temperature regulator housing (1) on the cylinder head.
Illustration 2 g02206193
Remove plastic tube assembly (2), plastic tube assembly (3), and plastic tube assembly (7) from clips (9).
Cut all cable straps (5) from engine wiring harness assembly (6). Position engine wiring harness assembly away from the engine. Note: Ensure that all cable straps are removed from the engine wiring harness.
Remove bolts (8) and remove bracket (4) from the cylinder head.
Illustration 3 g02206194
Follow Step 6.a through Step 6.b in order to disconnect harness assembly (15) from boost pressure sensor (13).
Slide locking tab (14) into the unlocked position.
Disconnect harness assembly (15) from boost pressure sensor (13).
Follow Step 7.a through Step 7.b in order to disconnect harness assembly (11) from inlet air temperature sensor (10).
Slide locking tab (12) into the unlocked position.
Disconnect harness assembly (11) from inlet air temperature sensor (10).
Remove all cable straps that secure the harness assembly to the cylinder head. The harness assembly should be positioned away from the cylinder head in order to avoid causing an obstruction during the removal of the cylinder head.
On some application there is an engine wiring harness support bracket on the rear of the cylinder head. if necessary, cut the cable straps and remove the engine wiring harness from the support bracket. Remove the support bracket from the cylinder head before removal the cylinder head assembly.
Illustration 4 g02206213
Remove bolt (16) from tube assembly (18). Remove bolt (20) from tube clip (19).
Remove tube assembly (18) from the cylinder head. Remove O-ring seal (17) (not shown) from the tube assembly. Plug the port in the cylinder head with a new plug. Cap the tube assembly with new cap.
Illustration 5 g02206214
Follow Step 12.a through Step 12.c in order to disconnect harness assembly (22) from coolant temperature sensor (23).
Slide locking tab (21) into the unlocked position.
Disconnect harness assembly (22) from coolant temperature sensor (23).
Cut cable strap (26) and remove harness assembly (22) from bypass tube (25).
Remove bolts (24).
Remove bypass tube (25) from the cylinder head. Remove O-ring seal (27) and O-ring seal (28) from bypass tube (25).
Illustration 6 g02206215
Illustration 7 g03417150
Sequence for tightening the bolts for the cylinder head
Gradually loosen bolts (29) in the reverse numerical order to the tightening sequence. Refer to the Illustration 7. Note: Follow the correct sequence in order to help prevent distortion of the cylinder head.
Remove bolt


Parts seal JOHNSON:

0322575
 
0322575 SEAL,Upper
100ML79S, 115EL77S, 115ETZ78C, 115ML79R, 115TXL77S, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 235TL78R, 85EL77S, 85ETLR78C, 85ML79R, 85TXLR77S, CJ275TLCDC, CJ275TLCOS, CJ30
0328650
 
0328650 SEAL, Carb. body
CJ275TLCOS, CJ300TLCOS, J120TLCDC, J120TLCOS, J120TLCUR, J140TLCDC, J140TLCOS, J140TLCUA, J185ESXENR, J185ESXESS, J185ESXETA, J185ESXW, J200CXATF, J200CXCCR, J200CXCEA, J200CXEIB, J200CXENE, J200CXESM, J200STLCDR, J200STLCUA, J225CLCUB, J225CXATF, J2
0326749
 
0326749 SEAL RING
BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, BJ135PLSIF, BJ200CXEDR, BJ200CXEEB, BJ200CXSSE, BJ200PLSIF, BJ225CXEEC, BJ225CXSSR, BJ225PLSIF, BJ250CXECB, BJ250CXEDA, BJ250CXEUM, CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, J120TLAEM,
0330970
 
0330970 SEAL, Drain indicator
CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, J120TLCCA, J120TLCDC, J120TLCOS, J120TLCUR, J140CXCCS, J140TLCDC, J140TLCOS, J140TLCUA, J200CXCCR, J200STLCDR, J200STLCUA, J225CLCUB, J225CXCCE, J225PTLCDA, J275CXCCA, J300CXCCA
0331018
 
0331018 SEAL, Front
CJ275TLCOS, CJ300TLCOS, J115GLSDE, J115PLSDA, J115PXSDA, J150CXSDE, J150GLSDE, J150PLSDD, J150PXSDD, J175CXSDE, J175GLSDE, J175PLSDD, J175PXSDD, J90GLSDE, J90PLSDM, J90PXSDR
0331231
 
0331231 SEAL, Rear lower
CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, J185ESXW, J200CXCEA, J225CXCED, J275CLCUR, J275CXCCA, J300CLCUR, J300CXCCA, J300CXCEM
0332585
SEAL
0332585 SEAL
BJ115TLEDA, BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, BJ135PLSIF, BJ200CXEDR, BJ200CXEEB, BJ200CXSSE, BJ200PLSIF, BJ225CXEEC, BJ225CXSSR, BJ225PLSIF, BJ250CXECB, BJ250CXEDA, BJ250CXEUM, CJ275TLCDC, CJ300TLCDC, D100WTLM, HJ88MSLEDC,
0912048
SEAL, Shaft
0912048 SEAL, Shaft
BJ200CXEDR, CJ275TLCDC, CJ300TLCDC, J185ESERK, J185ESXENR, J185ESXESS, J185ESXETA, J185ESXW, J200CXARC, J200CXATF, J200CXCCR, J200CXCEA, J200CXEIB, J200CXENE, J200CXEOC, J200CXESM, J200STLCDR, J200STLCUA, J225CLCUB, J225CXARC, J225CXATF, J225CXCCE, J
Back to top