5033208 SEAL, SIDE COVER DRAIN JOHNSON
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
SEAL
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- LOWER ENGINE COVER » 5033208
J10EL4SOR, J10R4SOA, J10RL4SOA, J10TBL4SOB, J10TE4SOA, J10TEL4SOA 2005
J10EL4SRC 2004
J10R4SDM 2006
J10R4SNF, J10RL4SNF, J10TE4SNF, J10TEL4SNF 2002
J10R4SR, J10RL4SR, J10TBL4SR, J10TE4SR, J10TEL4SR 2004
J10R4STC, J10RBL4STS, J10REL4STS, J10RL4STC, J10TBL4STC, J10TE4STC, J10TEL4STC 2003
J10R4SUB, J10RL4SUB 2007
J10RL4SDM 2006
J10TBL4SDE 2006
J10TBL4SUD, J10TE4SUB, J10TEL4SUB 2007
J10TE4SDM, J10TEL4SDM 2006
J15EL4SDC 2006
J15EL4SOS, J15R4SOA, J15RL4SOA, J15TE4SOA, J15TEL4SOA 2005
J15EL4SUR 2007
J15R4SDM 2006
J15R4SNF, J15RL4SNF, J15TE4SNF, J15TEL4SNF 2002
J15R4SR, J15TE4SR, J15TEL4SR 2004
J15R4STC, J15RL4STC, J15TE4STC, J15TEL4STC 2003
J15R4SUB, J15RL4SUB 2007
J15RL4SDM 2006
J15RL4SR 2004
J15TE4SDM, J15TEL4SDM 2006
J15TE4SUB, J15TEL4SUB 2007
Information:
Refer to Special Instruction, SEHS9278 for the instructions on the use of the 4C-8753 Extended Collet .Fuel setting is the adjustment of the fuel setting screw to a specified position. The fuel setting screw limits the power output of the engine by setting the maximum travel of all the fuel injector racks.
Illustration 1 g00323603
Synchronization and fuel setting tools (1) 8T-2684 Rack Synchronization Gauge (2) 6V-3075 Dial Indicator (3) 4C-8753 Extended Collet (4) 5P-7263 Indicator Contact Point Before the fuel setting is checked, the injectors must be correctly synchronized. Refer to Testing And Adjusting, "Fuel Injector Synchronization". After the injectors are synchronized correctly, leave the synchronization pin in place for the procedure that follows.
Put 6V-3075 Dial Indicator (2) with 5P-7263 Indicator Contact Point Contact Point (4) in 4C-8753 Extended Collet (3). Remove the plug from the right side of fuel setting cover (8) .
Illustration 2 g00323643
Installed dial indicator (typical example) (2) 6V-3075 Dial Indicator with 5P-7263 Indicator Contact Point (3) 4C-8753 Extended Collet
Move the governor or the actuator terminal shaft toward the ON position. The flat face of fuel stop lever (6) should make contact with synchronization pin (5). Hold the linkage in this position.
Illustration 3 g00323663
(2) 6V-3075 Dial Indicator (4) 5P-7263 Indicator Contact Point (5) Synchronization pin (6) Fuel stop lever
Install dial indicator (2) and extended collet (3) in the threaded hole. After indicator contact point (4) touches fuel stop lever (6), slide dial indicator (2) until the indicator reads zero. Keep the dial indicator in this position by tightening collet (3) .
Illustration 4 g00805403
Checking fuel setting (typical example) (2) 6V-3075 Dial Indicator (5) Synchronization pin (8) Fuel setting cover
Unscrew synchronization pin (5) by 25 mm (1 inch) or remove synchronization pin (5). Slowly move the governor or the actuator terminal shaft toward the fuel ON position until the flat face of the fuel stop lever is against the end of the fuel setting screw. The dial indicator reading will be the present fuel setting when the linkage is held in this position.Note: Refer to the TMI (Technical Marketing Information) for the correct fuel setting.
If the fuel setting is correct, remove the dial indicator and the synchronization pin. Install the two plugs, and install the synchronization pin back into cover (8) .
If the fuel setting needs adjustment, see "Fuel Setting Adjustment".
A mechanic with governor and fuel setting training is the ONLY one to make adjustments to the engine fuel setting.
Fuel Setting Adjustment
Cut the seal wire and remove fuel setting cover (8) and the gasket. Loosen locknut (7). Hold the fuel stop lever against the end of the fuel setting screw. Turn the fuel setting screw clockwise or counterclockwise until the correct reading is on the dial indicator.
Illustration 5 g00323705
Adjustment of the fuel setting screw (typical example)
Now tighten locknut (7). Be sure that the fuel setting screw does not turn when the locknut is tightened. Release the fuel system linkage and move the linkage toward the fuel ON position. Check the dial indicator reading again in order to be sure that the fuel setting is still correct.
Remove dial indicator (2) and synchronization pin (5). Install the two plugs.
Illustration 6 g00323706
Installed cover (typical example) (7) Locknut (8) Fuel setting cover
Put fuel setting cover (8) and the gasket in position over the fuel setting screw. Install the bolt and synchronization pin (5) in the cover. Install a new seal wire.
Illustration 1 g00323603
Synchronization and fuel setting tools (1) 8T-2684 Rack Synchronization Gauge (2) 6V-3075 Dial Indicator (3) 4C-8753 Extended Collet (4) 5P-7263 Indicator Contact Point Before the fuel setting is checked, the injectors must be correctly synchronized. Refer to Testing And Adjusting, "Fuel Injector Synchronization". After the injectors are synchronized correctly, leave the synchronization pin in place for the procedure that follows.
Put 6V-3075 Dial Indicator (2) with 5P-7263 Indicator Contact Point Contact Point (4) in 4C-8753 Extended Collet (3). Remove the plug from the right side of fuel setting cover (8) .
Illustration 2 g00323643
Installed dial indicator (typical example) (2) 6V-3075 Dial Indicator with 5P-7263 Indicator Contact Point (3) 4C-8753 Extended Collet
Move the governor or the actuator terminal shaft toward the ON position. The flat face of fuel stop lever (6) should make contact with synchronization pin (5). Hold the linkage in this position.
Illustration 3 g00323663
(2) 6V-3075 Dial Indicator (4) 5P-7263 Indicator Contact Point (5) Synchronization pin (6) Fuel stop lever
Install dial indicator (2) and extended collet (3) in the threaded hole. After indicator contact point (4) touches fuel stop lever (6), slide dial indicator (2) until the indicator reads zero. Keep the dial indicator in this position by tightening collet (3) .
Illustration 4 g00805403
Checking fuel setting (typical example) (2) 6V-3075 Dial Indicator (5) Synchronization pin (8) Fuel setting cover
Unscrew synchronization pin (5) by 25 mm (1 inch) or remove synchronization pin (5). Slowly move the governor or the actuator terminal shaft toward the fuel ON position until the flat face of the fuel stop lever is against the end of the fuel setting screw. The dial indicator reading will be the present fuel setting when the linkage is held in this position.Note: Refer to the TMI (Technical Marketing Information) for the correct fuel setting.
If the fuel setting is correct, remove the dial indicator and the synchronization pin. Install the two plugs, and install the synchronization pin back into cover (8) .
If the fuel setting needs adjustment, see "Fuel Setting Adjustment".
A mechanic with governor and fuel setting training is the ONLY one to make adjustments to the engine fuel setting.
Fuel Setting Adjustment
Cut the seal wire and remove fuel setting cover (8) and the gasket. Loosen locknut (7). Hold the fuel stop lever against the end of the fuel setting screw. Turn the fuel setting screw clockwise or counterclockwise until the correct reading is on the dial indicator.
Illustration 5 g00323705
Adjustment of the fuel setting screw (typical example)
Now tighten locknut (7). Be sure that the fuel setting screw does not turn when the locknut is tightened. Release the fuel system linkage and move the linkage toward the fuel ON position. Check the dial indicator reading again in order to be sure that the fuel setting is still correct.
Remove dial indicator (2) and synchronization pin (5). Install the two plugs.
Illustration 6 g00323706
Installed cover (typical example) (7) Locknut (8) Fuel setting cover
Put fuel setting cover (8) and the gasket in position over the fuel setting screw. Install the bolt and synchronization pin (5) in the cover. Install a new seal wire.
Parts seal JOHNSON:
5030928
5030928 SEAL, Lower, cover
BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, J10R4SNF, J15R4SNF, J60PL4SNF, J70FLTLECS, J70PL4SNF
5033012
5033012 SEAL, CAMSHAFT OIL
J10EL4SRC, J10R4SNF, J10R4SR, J10R4STC, J15R4SNF, J15R4SR, J15R4STC, J15RL4SR
5031269
5031269 SEAL, VALVE STEM
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF
5033013
5033013 SEAL, CRANKSHAFT OIL
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
5033180
5033180 SEAL, UPPER MOUNT PORT
J10EL4SRC, J10R4SNF, J10R4SR, J10R4STC, J15R4SNF, J15R4SR, J15R4STC, J15RL4SR
5033181
5033181 SEAL, UPPER MOUNT STBD
J10EL4SRC, J10R4SNF, J10R4SR, J10R4STC, J15R4SNF, J15R4SR, J15R4STC, J15RL4SR
5033212
5033212 *SEAL, RECOIL STARTER
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
5036749