5037055 SEAL, Side cover JOHNSON
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC
SEAL
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- LOWER ENGINE COVER » 5037055
BJ25R4SDS, BJ25RL4SDS, J25R4SDC, J25RL4SDC 2006
BJ25R4SUC, BJ25RL4SUC, J25R4SUR, J25RL4SUR 2007
BJ25TE4SDS, BJ25TEL4SDS, J25TE4SDC, J25TEL4SDC 2006
BJ25TE4SUC, BJ25TL4SUC, J25TE4SUR, J25TEL4SUR 2007
Information:
Table 1
Required Tooling Quantity
323-3949 Test Kit 1
558-4574 Rail Plug As 1
356-0828 Fuel Injection Line As 1
356-5217 Fuel Injection Line As 3
356-0831 Fuel Injection Line As 1
356-0832 Fuel Injection Line As 2
9S-8927 Plugs 2
8S-4950 Caps 3
9S-5518 Plugs 2
9L-8493 Flared Caps 2
Fuel injection lines MUST only be used once. Discard all fuel injection lines after use.
Illustration 1 g02039499
323-3949 Test Kit
(1) 356-2468 Foam Lid
(2) 356-2470 Graduated Cylinder
(3) 356-2466 Plastic Case
(4) 323-3950 Discharge Orifice As
(5) 354-8301 Pump Drain Hose
(6) 355-8794 Gage Pin
(7) 356-2469 Foam Block
(8) 355-8626 Nut
(9) 558-4574 Rail Plug AsNote: The 323-3951 Plug As that come with the kit are not used for this procedure. Use the 558-4574 Rail Plug As instead.Test Procedure
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
Before beginning any work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during all work on the fuel system.
Note: Use the gage pin (6) or an aerosol cleaner to ensure that the orifice is clean before performing this procedure.Test Step 1: Measure the Fuel Leak From the Pressure Relief Valve (PRV)
Illustration 2 g06258452
(1) Pressure Relief Valve (PRV) fuel line
Remove fuel return line (1) from the PRV on the high-pressure fuel rail to the low-pressure regulator block.
Cap the port at the regulator block using the 9L-8493 Flared Cap.
Route the PRV fuel line into graduated cylinder (2).Note: Ensure that the PRV fuel line does not have any obstructions or residual fuel.
Use the Cat® Electronic Technician (ET) "Injection Disable Override" to disable the fuel injectors or disconnect the fuel injectors electrical connector on the side of the cylinder head.Note: Leave the injectors disabled during the test.
Turn the keyswitch to ON for 30 seconds to prime the fuel system. After priming has been completed, crank the engine for 20 seconds and record the fuel volume that collects in the graduated cylinder.
If the measured volume of fuel is more than 5 drops, replace the PRV. Repeat the test to verify the repair. Proceed to Test Step 4.
If the measured volume of fuel is fewer than 5 drops, reinstall the PRV fuel line to the low-pressure regulator block. Proceed to Test Step 2.Test Step 2: Measure the Pressure and Flow of the Fuel Rail while Cranking
Illustration 3 g06258456
(3) High-pressure fuel supply line
(5) 323-3950 Discharge Orifice AsNote: Illustration 3 shows discharge orifice assembly (5) attached to injector supply line number 3. The discharge orifice assembly can be installed to any injector supply line as long as the other 5 injectors ports are plugged on the fuel rail.
Remove the fuel lines for the injectors from the fuel rail.
Install the 558-4574 Rail Plug As on the rail for cylinders 1, 2, 4, 5, and 6.
Use the 355-8794 Gage Pin to ensure that the discharge orifice is free of any obstruction.
Illustration 4 g06257833
(5) 323-3950 Discharge Orifice As
Install discharge orifice assembly (5) on injector port 3. Route the discharge orifice assembly hose to the 356-2470 Graduated Cylinder.
Use the Cat® Electronic Technician (ET) "Injection Disable Override" to disable the fuel injectors or disconnect the fuel injectors electrical connector on the side of the cylinder head.Note: Leave the injectors disabled during the test.
Turn the keyswitch to ON for 30 seconds to prime the fuel system. Then crank the engine for 30 seconds and record the fuel volume in the graduated cylinder.
The volume of the fuel is less than 65 mL (2.2 oz). Replace the high-pressure fuel pump and proceed to Test Step 4.Note: Ensure that the low-pressure fuel system is providing a minimum of 210 kPa (30.5 psi) during the cranking process.
The volume of the fuel is greater than 65 mL (2.2 oz). Proceed to Step 7 to check the fuel rail pressure.
Navigate in Cat ET to the "Status Parameters > Fuel Delivery" screen. Record the "Fuel Rail Pressure" and "Engine Speed" while t
Parts seal JOHNSON:
0343736
0343736 SEAL, Fuel connector
AM55RSLD, BJ10FAEUR, BJ10FDLECM, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15FAEUA, BJ15FDLECM, BJ15RELEUC, BJ20SEECB, BJ20SEEUM, BJ20SRECB, BJ20SREUM, BJ25ARECA, BJ25AREUR, BJ25BAECM, BJ25BAEUA, BJ25E4SDS, BJ25E4SUC,
5031269
5031269 SEAL, VALVE STEM
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF
5036817
5036817 *SEAL, Crankshaft oil lower
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC
5036818
5036818 *SEAL, Crankshaft oil upper
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC
5037038
5036966
5037057
5037058