0398692 JOHNSON STOP SWITCH ASSY.


0398692 STOP SWITCH ASSY. JOHNSON D25RWA, J10ECCD, J10ECES, J10ECUE, J15ECCS, J15ECEC, J15ECUD, J20CRCCA, J20CRCEM, J20CRCUR, J25ECCM, J25ECUA, J25RCEM, J25RWCUR, J25RWK, J25TECEM, J30ECCE, J30ECUB, J30RCED, J30TECED, J35AELCUD, J35RCCE, J35RCED, J35RCUB, J40AELCCS, J40ECEC, J40ECUD, STOP
0398692 STOP SWITCH ASSY. JOHNSON
Rating:
60

Buy STOP SWITCH ASSY. 0398692 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$111.54
 

02-07-2023

-: -
0398692 Rely Made 48-22-5032 Measuring 305mm Metric/Meters (not inches/feet)
GenuineBrandedLike on photo. Premium Quality. Usefull tool
$160.71

22-03-2025
0.4[0.18] Pounds
US: LEADERS RPM
Johnson/Evinrude/OMC New OEM Tiller Handle Stop Kill Switch Kit 398692, 0398692
Johnson Evinrude OMC Superseded Part Number: 0583974 || Sold Each || Please verify your own fitment || Superseded Part Number: 0583974
Number on catalog scheme: 103
 

BRP JOHNSON entire parts catalog list:

D25RWA, D25RWLA 1988
J10ECCD, J10ELCCD, J10RCCD, J10RLCCD, J10SELCCD 1988
J10ECES, J10ELCES, J10RCES, J10RLCES, J10SELCES, TJ10ELCES, TJ10RLCES 1989
J10ECUE, J10ELCUE, J10RCUE, J10RLCUE, J10SELCUE 1987
J15ECCS, J15ELCCS, J15RCCS, J15RLCCS 1988
J15ECEC, J15ELCEC, J15RCEC, J15RLCEC, TJ15RLCEC 1989
J15ECUD, J15ELCUD, J15RCUD, J15RLCUD 1987
J20CRCCA, J20CRLCCA, J20ECCA, J20ELCCA 1988
J20CRCEM, J20CRLCEM, TJ20CRCEM, TJ20CRLCEM, TJ20CRLESF 1989
J20CRCUR, J20CRLCUR, J20ECUR, J20ELCUR 1987
J25ECCM, J25ELCCM, J25RCCA, J25RLCCA, J25TECCA, J25TELCCA 1988
J25ECUA, J25ELCUA, J25RCUR, J25RLCUR, J25TECUR, J25TELCUR 1987
J25RCEM, J25RLCEM 1989
J25RWCUR, J25RWLCUR 1987
J25RWK, J25RWLK 1989
J25TECEM, J25TELCEM 1989
J30ECCE, J30ELCCE, J30RCCE, J30RLCCE, J30TECCE, J30TELCCE 1988
J30ECUB, J30ELCUB, J30RCUB, J30RLCUB, J30TECUB, J30TELCUB 1987
J30RCED, J30RLCED 1989
J30TECED, J30TELCED 1989
J35AELCUD, J35ARLCUD 1987
J35RCCE, J35RLCCE 1988
J35RCED, J35RLCED 1989
J35RCUB, J35RLCUB 1987
J40AELCCS, J40ARLCCS, J40ATLCCS, J40ECCS, J40ELCCS, J40RCCS, J40RLCCS, J40TECCS, J40TELCCS, J40TLCCS, J40TTLCCS 1988
J40ECEC, J40ELCEC, J40RCEC, J40RLCEC, J40TECEC, J40TELCEC, J40TLCEC, J40TTLCEC, TJ40ELCEC 1989
J40ECUD, J40ELCUD, J40RCUD, J40RLCUD, J40TECUD, J40TLCUD 1987
J45RCCUC, J45RCLCUC 1987
J45RCE, J45RCLE, J45WMLE 1989
J4RDHCCS, J4RDHLCCS 1988
J4RDHCEC, J4RDHLCEC 1989
J4RDHCUD, J4RDHLCUD 1987
J50BECCS, J50BELCCS, J50TELCCS, J50TLCCS 1988
J50BECEC, J50BELCEC, J50TLCEC, TJ50TLCEC, TJ50TLESF 1989
J50BECUD, J50BELCUD, J50TELCUD, J50TLCUD 1987
J50TELCEC 1989
J55RWLCUC 1987
J55RWLE 1989
J60ELCCR, J60TLCCR, J60TTLCCR 1988
J6RCCS, J6RLCCS, J6SLCCS 1988
J6RCUD, J6RLCUD, J6SLCUD 1987
J8RCCS, J8RLCCS, J8SRLCCS 1988
J8RCUD, J8RLCUD, J8SRLCUD 1987
R55RWLR 1988
S45RCLR, S45RCR 1988
VJ14RCCS 1988
VJ14RCCS 1988
VJ14RCEC 1989
VJ14RCEC 1989

Information:

The mode selection switch uses resistors to modify the voltage signal from the ECM. The resistance of the switch changes dependent on which position the switch is in. The ECM uses the signal voltage to determine which mode has been selected.
Illustration 1 g03117957
View of the signal voltage range for the mode selection switch
Note: Position (4) is not available on the mode selection switch. If the signal voltage range is between 3.7 and 4.4 VDC, the mode that is selected will be the same as position (3).
Illustration 2 g03728025
Typical example of the schematic for the mode selection switch
Not all connectors are shown. Refer to the Electrical Schematic for the application.
Illustration 3 g02723018
Typical view of the pin locations on the P1 connector for the mode selection switch
(55) Mode selection switch signal
(77) Mode selection switch ground
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P1/J1 connector.
B. Thoroughly inspect the connector for the mode selection switch.
C. Refer to Troubleshooting, "Electrical Connectors - Inspect".
D. Perform a 30 N (6.7 lb) pull test on each of the wires in the connectors that are associated with the mode selection switch.
E. Check the harness for abrasions and for pinch points from the switch back to the ECM.
Damaged wire or connector
Result: A damaged wire or damaged connector was not found.
Proceed to Test Step 2.
Result: A damaged wire or damaged connector was found.
Repair: Repair the damaged wire or the damaged connector.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
2. Check for Active or Recently Logged Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Do not start the engine.
D. Check for active diagnostic codes with the mode selection switch in each position. Wait at least 10 seconds with the switch in each position for activation of the diagnostic codes.
Diagnostic Trouble Codes
Result: A 2880-4 diagnostic code is active.
Proceed to Test Step 3.
Result: A 2880-3 diagnostic code is active.
Proceed to Test Step 4.
Result: A 2880-2 diagnostic code is active.
Proceed to Test Step 5.
3. Create an Open Circuit at the Switch
A. Turn the keyswitch to the OFF position.
B. Disconnect the mode selection switch.
C. Turn the keyswitch to the ON position.
D. Use the electronic service tool to check for an active 2880 diagnostic code. Wait at least 10 seconds for activation of the diagnostic codes.
E. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: A 2880-3 diagnostic code is active with the switch disconnected.
Repair: Replace the mode selection switch.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: A 2880-4 diagnostic code is still active with the switch disconnected.
Reconnect the switch and proceed to Test Step 7.
4. Create a Short at the Switch Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the mode selection switch.
C. Fabricate a jumper wire and install the jumper wire between the two harness connector terminals for the mode selection switch.
D. Turn the keyswitch to the ON position.
E. Use the electronic service tool to check for an active 2880 diagnostic code. Wait at least 10 seconds for activation of the diagnostic codes.
F. Turn the keyswitch to the OFF position.
G. Remove the jumper wire.
Diagnostic codes
Result: A 2880-4 diagnostic code is active with the jumper installed.
Repair: Replace the mode selection switch.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: A 2880-3 diagnostic code is still active with the jumper installed.
Reconnect the mode selection switch and proceed to Test Step 7.
5. Check the Voltage at the Switch Connector
A. Turn the keyswitch to the OFF position.
B. Disconnect the mode selection switch.
C. Turn the keyswitch to the ON position.
D. Use a suitable multimeter to measure the voltage between the signal terminal and the ground terminal at the switch connector.
E. Turn the keyswitch to the OFF position.
4.9 V to 5.1 V
Result: The voltage is within the expected range.
Repair: Replace the mode selection switch.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: The voltage is not within the expected range.
Proceed to Test Step 6.
6. Check the Wiring for High Resistance
A. Turn the keyswitch to the OFF position.
B. Disconnect the mode selection switch. Disconnect the P1 connector.
C. Use a suitable multimeter to measure the resistance between the following points:
P1:55 to the signal terminal at the switch connector
P1:77 to the ground terminal at the switch connector
Less than 5 Ohms
Result: At least one of the resistance measurements is greater than 5 Ohms.
The fault is in the wiring between the switch connector and the P1 connector.
Repair: Replace the faulty wiring.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: Both resistance measurements are less than 5 Ohms.
Proceed to Test Step 7.
7. Check the Wiring for a Short Circuit
A. Turn the keyswitch to the OFF position.
B. Disconnect the P1 connector from the ECM.
C. Disc


Parts stop JOHNSON:

0386842
 
0386842 STOP, Leaf
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, J10ECCD, J10ECDB, J10ECES, J10ECOM, J10ECSE, J10ECUE, J10EEIR, J10EENA, J10EESC, J10ELCID, J10ELCNS, J10ELCRA, J10ELCTC, J15ECCS, J15ECDE, J15ECEC, J15EC
0122542
 
0122542 STOP, Piston rod
115EL77S, 115ESL74B, 115ESL75E, 135ESL74B, 135ESL75E, 85EL76D, 85EL77S, J35AELCDE, J35AELCUD, J40AELCCS, J40ECDE, J40ECUD, J45RCE, J50BECCS, J50BECDE, J50BECIC, J50BECNR, J50BECOB, J50BECRM, J50BECTA, J50BECUD, J55RCIM, J55RWLE, J60ECIA, J60ECNM, J60
0320536
STOP, Idle adjustment
0320536 STOP, Idle adjustment
50ES75B, 50R79C, 55E76E, 55E77D, 55E78S, 55E79C, J35AELCDE, J35AELCUD, J40AELCCS, J40ECDE, J40ECOB, J40ECRM, J40ECUD, J45RCE, J45RCEIA, J45RCENM, J45RCESR, J48ESLCCC, J48ESLCCC, J48ESLCUS, J48ESLCUS, J50BECCS, J50BECDE, J50BECIC, J50BECNR, J50BECOB,
0322407
 
0322407 STOP, Shift lock
10E78M, 10EL79B, 15E78B, 15E79E, J10ECCD, J10ECDB, J10ECES, J10ECOM, J10ECSE, J10ECUE, J10EEIR, J10EENA, J10EESC, J10ELCID, J10ELCNS, J10ELCRA, J10ELCTC, J15ECCS, J15ECDE, J15ECEC, J15ECIS, J15ECNC, J15ECOB, J15ECRM, J15ECSD, J15ECTR, J15ECUD, J15EEI
0326499
 
0326499 STOP LINK,Stbd.
J35AELCDE, J35AELCUD, J40ECDE, J40ECOB, J40ECRM, J40ECUD, J45RCCDS, J45RCCUC, J45RCE, J50BECDE, J50BECIC, J50BECNR, J50BECOB, J50BECRM, J50BECTA, J50BECUD, J50ECSR, J55RCIM, J55RLCSA, J55RSLN, J55RWLCDC, J55RWLCOS, J55RWLCRD, J55RWLCUC, J55RWLE, J60E
0331783
 
0331783 STOP, Idle spark
J6RCCS, J6RCDE, J6RCEC, J6RCUD, J6RESR, J8RCCS, J8RCDE, J8RCEC, J8RCUD, J8RESR
0332199
 
0332199 STOP LINK, Stbd.
AM55RSLD, HJ45RCLEDS, HJ45RCLEUC, HJ55RSLC, HJ55RSLW, HJ55WMLM, HJ55WMLZ, J35AELCDE, J35AELCUD, J40AELCCS, J40ECDE, J40ECUD, J40WREES, J40WRLSIR, J40WRLSSC, J45RCEIA, J45RCENM, J45RCEOD, J45RCERE, J45RCESR, J45RCETB, J48ESLCCC, J48ESLCCC, J48ESLCUS,
0332198
 
0332198 STOP LINK, Port
J35AELCDE, J35AELCUD, J40AELCCS, J40ECDE, J40ECUD, J45RCE, J50BECCS, J50BECDE, J50BECUD, J55RWLE
Back to top