0325792 JOHNSON SET SCREW, Bellcrank


0325792 SET SCREW, Bellcrank JOHNSON BJ3REDS, BJ4BREDS, BJ4BREUC, J2RTSIA, J2WRSIR, J3BRCEC, J3BRESR, J3RCCM, J3RCUA, J3REIA, J3RENM, J3REOD, J3RERE, J3RETB, J3REUC, J3RSDE, J3RSNF, J3RSOD, J3RSRE, J3RSTB, J3RTLSIA, J3WRSIR, J4BRCIC, J4BRECRJ, J4BRHCCS, J4BRHCDE, J4BRHCNR, J4BRHCOB, J4B SET
0325792 SET SCREW, Bellcrank JOHNSON
Rating:
58

Buy SET SCREW, Bellcrank 0325792 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 44
 

BRP JOHNSON entire parts catalog list:

BJ3REDS, SJ3REDS 1996
BJ4BREDS, BJ4BRLEDS, BJ4REDS, BJ4RLEDS, J4REDS, J4RLEDS, SJ4REDS, SJ4RLEDS 1996
BJ4BREUC, BJ4BRLEUC, J4REUC, J4RLEUC 1997
J2RTSIA, J2RTVSIA 2001
J2WRSIR 2001
J3BRCEC 1989
J3BRESR 1990
J3RCCM 1988
J3RCUA 1987
J3REIA 1991
J3RENM 1992
J3REOD 1995
J3RERE 1994
J3RETB 1993
J3REUC 1997
J3RSDE 2006
J3RSNF 2002
J3RSOD 2005
J3RSRE 2004
J3RSTB, J3RSTF 2003
J3RTLSIA, J3RTSIA, J3RTVSIA 2001
J3WRSIR 2001
J4BRCIC, J4BRLCIC 1981
J4BRECRJ, J4BRLECRJ 1998
J4BRHCCS, J4BRHLCCS 1988
J4BRHCDE, J4BRHLCDE 1986
J4BRHCNR, J4BRHLCNR 1982
J4BRHCOB, J4BRHLCOB 1985
J4BRHCRM, J4BRHLCRM 1984
J4BRHCTA, J4BRHLCTA 1983
J4BRHCUD, J4BRHLCUD 1987
J4RCCS, J4RLCCS 1988
J4RCEC, J4RLCEC 1989
J4RCUD, J4RLCUD 1987
J4REEA, J4RLEEA 1999
J4REIA, J4RLEIA 1991
J4RENM, J4RLENM 1992
J4REOD, J4RLEOD 1995
J4RERE, J4RLERE 1994
J4RESR, J4RLESR 1990
J4RETB, J4RLETB 1993
J4RLSIB, J4RSIB 2001
J4RLSSM, J4RSSM 2000

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 207-5034(1) Stud Tensioner Tool Gp 1
301-5215(2) Stud Tensioner Tool Gp 1
B 8T-3035 Hydraulic Line 1
8T-0820 Hydraulic Pressure Gauge 1
3S-6224(3) Electric Hydraulic Pump
(115 Volt 50/50 Hz) 1
8S-8033(3) Electric Hydraulic Pump
(230 Volt 50/60 Hz) 1
9U-6600(3) Hand Hydraulic Pump 1
C 8T-0960 Handling Tool Group 1
D 134-0932 Main Bearing Driver 1
E 3P-1529 Circular Level 1
(1) Operating pressure is 65000 2400 kPa (9425 348 psi).
(2) Operating pressure is 111500 3950 kPa (16170 575 psi).
(3) Three hydraulic pumps are listed. Only one pump is necessary in order to carry out the job.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01302245Note: The bearing has a locating tab. When the bearing is viewed from the flywheel, counterclockwise rotation is required for the installation of the upper half of the bearing. Ensure that the tab is properly seated in the groove. Ensure that the tab does not break in the groove.Note: If the main bearing cap bolts were removed, use a tap in order to clean the threads in the cylinder block prior to the installation of the bolts. Tighten the bolts to a torque of 100 20 N m (75 15 lb ft).
Use a clean cloth in order to wipe the upper half of main bearing (11). Apply clean engine oil to the main bearing. Use Tooling (D) in order to roll the upper half of the main bearing into the cylinder block. Note: On the C280-06 Engine, the Number 4 main bearing journal does not have an oil hole. Tooling (D) cannot be used in order to roll the upper half of the main bearing in the cylinder block. In order to install the Number 4 main bearing, protect the crankshaft and rap the side of the bearing with the tab with a narrow tool.Note: On the C280-08 Engine, the Number 5 main bearing journal does not have an oil hole. Tooling (D) cannot be used in order to roll the upper half of the main bearing in the cylinder block. In order to install the Number 5 main bearing, protect the crankshaft and rap the side of the bearing with the tab with a narrow tool.
Illustration 2 g00644087
Install thrust plates (12). If necessary, carefully pry the crankshaft in order to roll the thrust plates into position in the cylinder block. Note: Install the thrust plates on the rear main bearing for rear driven equipment. Install the thrust plates on the front main bearing for front driven equipment.
Illustration 3 g01302251
Use a clean cloth in order to wipe the lower half of main bearing (14) and the bore in the main bearing cap. Ensure that there is no thread lubricant on the lower half of the main bearing or on the main bearing cap. Install the lower half of main bearing (14) in the main bearing cap. Ensure that the tab on the back of the main bearing is engaged with the slot in the main bearing cap.
Apply clean engine oil to the lower half of main bearing (14). Be sure not to apply the engine oil to the back side of the main bearing.
Assemble the saddle bolts. Apply clean engine oil to the washer face and the threads prior to assembly.
Use Tooling (C) in order to raise the main bearing cap on the studs. The weight of each main bearing cap is approximately 70 kg (155 lb).
Ensure that dowel (13) engages with the hole in the cylinder block. The dowel should extend 10.0 0.5 mm (0.39 0.02 inch) from the main bearing cap.
Install the saddle bolts on the side of the tab on the main bearing cap hand tight.
Install the saddle bolts on the side opposite of the tab on the main bearing cap hand tight.
Install the washers and nuts in order to hold the main bearing cap. Tighten the nuts by hand. Remove Tooling (C) from the main bearing cap.
Remove the pins from the bearing cap.
Illustration 4 g00644075Note: The Collar Retainer, the Stud Tensioner Cylinder, and the Threaded Collar are part of Tooling (A).
Place Collar Retainer (8) on top of Stud Tensioner Cylinder (7) in order to determine the bolts that need to be removed from the Stud Tensioner Cylinder. Remove the four appropriate bolts from the Stud Tensioner Cylinder.
Insert the Threaded Collar in the center of Stud Tensioner Cylinder (7).
Install Collar Retainer (8) in order to retain Threaded Collar (6) in Stud Tensioner Cylinder (7).
Use bolts (9) in order to fasten Collar Retainer (8) to Stud Tensioner Cylinder (7).


Back to top