5032101 SHAFT, PROPELLER JOHNSON
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, J30PL4SDR, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
SHAFT
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- GEARS » 5032101
BJ25R4SDS, BJ25RL4SDS, J25R4SDC, J25RL4SDC 2006
BJ25R4SUC, BJ25RL4SUC, J25R4SUR, J25RL4SUR 2007
BJ25TE4SDS, BJ25TEL4SDS, J25TE4SDC, J25TEL4SDC 2006
BJ25TE4SUC, BJ25TL4SUC, J25TE4SUR, J25TEL4SUR 2007
J30PL4SDR 2006
J30PL4SUA 2007
J30TEL4SDR 2006
J30TEL4SUA 2007
Information:
Recommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.Diagnostic Codes and Event Codes
Certain diagnostic codes and/or event codes may cause poor performance. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes. Troubleshoot any codes that are present before continuing with this procedure.Cold Mode
Use Cat ET to verify that the engine has exited cold mode. Cold mode operation may cause the engine to run rough and engine power may be limited.
Observe the coolant temperature on the Cat ET status screen. Verify that the reading is valid. Throttle Signal
Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed. Refer to the appropriate diagnostic test for your application:
Troubleshooting, "Throttle Position Sensor Circuit - Test"
Troubleshooting, "Throttle Switch Circuit - Test"
Troubleshooting, "Speed Control - Test"Electrical Connectors
Check for correct installation of the J1/P1 and J2/P2 Electronic Control Module (ECM) connectors and the unit injector connectors. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".Unit Injectors
Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
Perform the "Cylinder Cutout Test" on Cat ET in order to identify any misfiring cylinder(s). Refer to the diagnostic functional test Troubleshooting, "Injector Solenoids Circuit - Test". Intake Manifold (Boost) Pressure Sensor
Monitor the status of "Fuel Position", "Rated Fuel Limit", and "FRC Fuel Limit" on Cat ET while the engine is operating under full load. These parameters should reflect the information below.
Table 1
"Fuel Position" = "Rated Fuel Limit"
and
"Fuel Position" < "FRC Fuel Limit" If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the electronics are operating correctly. Otherwise, proceed with the next Step.
Monitor the status of "Boost Pressure" and "Atmospheric Pressure" for normal operation on Cat ET. When the engine is not running, the correct value for "Boost Pressure" is 0 kPa (0 psi). Air Inlet and Exhaust System
Observe the indicator lamps. Check for an air filter restriction indicator. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.
Check the air inlet and exhaust system for restrictions and/or for leaks. Refer to Systems Operation/Testing and Adjusting, "Air Inlet and Exhaust System". Parameters
If the ECM has been replaced, compare the values on the Engine Information Plate to the following parameters from Cat ET:
FRC offset
Full Load Setting (FLS)
Full Torque Setting (FTS)Verify that the correct flash file is installed.Fuel Supply
Check the fuel lines for the following problems: restrictions, collapsed lines and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Check the fuel tank for foreign objects which may block the fuel supply.
Prime the fuel system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsNote: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel. Refer to Systems Operation/Testing and Adjusting, "Air in Fuel - Test".
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.
Check the fuel pressure after the fuel filter while the engine is being cranked. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for the correct pressure values. If the fuel pressure is low, replace the fuel filters. If the fuel pressure is still low, check the following items: fuel transfer pump, fuel transfer pump coupling and fuel pressure regulating valve. Refer to Systems Operation/Testing and Adjusting for more information.
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.Diagnostic Codes and Event Codes
Certain diagnostic codes and/or event codes may cause poor performance. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes. Troubleshoot any codes that are present before continuing with this procedure.Cold Mode
Use Cat ET to verify that the engine has exited cold mode. Cold mode operation may cause the engine to run rough and engine power may be limited.
Observe the coolant temperature on the Cat ET status screen. Verify that the reading is valid. Throttle Signal
Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed. Refer to the appropriate diagnostic test for your application:
Troubleshooting, "Throttle Position Sensor Circuit - Test"
Troubleshooting, "Throttle Switch Circuit - Test"
Troubleshooting, "Speed Control - Test"Electrical Connectors
Check for correct installation of the J1/P1 and J2/P2 Electronic Control Module (ECM) connectors and the unit injector connectors. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".Unit Injectors
Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM.
Perform the "Cylinder Cutout Test" on Cat ET in order to identify any misfiring cylinder(s). Refer to the diagnostic functional test Troubleshooting, "Injector Solenoids Circuit - Test". Intake Manifold (Boost) Pressure Sensor
Monitor the status of "Fuel Position", "Rated Fuel Limit", and "FRC Fuel Limit" on Cat ET while the engine is operating under full load. These parameters should reflect the information below.
Table 1
"Fuel Position" = "Rated Fuel Limit"
and
"Fuel Position" < "FRC Fuel Limit" If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the electronics are operating correctly. Otherwise, proceed with the next Step.
Monitor the status of "Boost Pressure" and "Atmospheric Pressure" for normal operation on Cat ET. When the engine is not running, the correct value for "Boost Pressure" is 0 kPa (0 psi). Air Inlet and Exhaust System
Observe the indicator lamps. Check for an air filter restriction indicator. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.
Check the air inlet and exhaust system for restrictions and/or for leaks. Refer to Systems Operation/Testing and Adjusting, "Air Inlet and Exhaust System". Parameters
If the ECM has been replaced, compare the values on the Engine Information Plate to the following parameters from Cat ET:
FRC offset
Full Load Setting (FLS)
Full Torque Setting (FTS)Verify that the correct flash file is installed.Fuel Supply
Check the fuel lines for the following problems: restrictions, collapsed lines and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Check the fuel tank for foreign objects which may block the fuel supply.
Prime the fuel system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsNote: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel. Refer to Systems Operation/Testing and Adjusting, "Air in Fuel - Test".
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.
Check the fuel pressure after the fuel filter while the engine is being cranked. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for the correct pressure values. If the fuel pressure is low, replace the fuel filters. If the fuel pressure is still low, check the following items: fuel transfer pump, fuel transfer pump coupling and fuel pressure regulating valve. Refer to Systems Operation/Testing and Adjusting for more information.
Parts shaft JOHNSON:
5032665
5032665 SHAFT, TILT CYL LOWER
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5032836
5032836 SHAFT, TILT CYL UPPER
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5032404
5032404 SHAFT ASSY
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5032094
5032094 SHAFT, DRIVE (L)
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5032012
5032012 SHAFT, CLUTCH
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5034694
5034694 SHAFT, STEERING LOCK
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5031950
5031950 SHAFT, INTAKE ROCKER ARM
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5031951
5031951 SHAFT, EXHAUST ROCKER ARM
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA