0338295 JOHNSON SHELL, Throttle lever


0338295 SHELL, Throttle lever JOHNSON BJ10EEDD, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15RELEUC, HJ15KCF, HJ15KCLN, HJ15KCLO, J10EECC, J10EEOE, J10EERB, J10EETM, J10ELEER, J10ELSIM, J10ELSSA, J10RLSUR, J15EECR, J15EEOD, J15EERE, J15EETB, J15ELEEA, J15ELSI SHELL
0338295 SHELL, Throttle lever JOHNSON
Rating:
18

Buy SHELL, Throttle lever 0338295 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 48
 

BRP JOHNSON entire parts catalog list:

BJ10EEDD, BJ10ELEDD, BJ10REDD, BJ10RELEDD, BJ10RLEDD, BJ10SELEDD, J10EEDD, J10ELEDD, J10REDD, J10RELEDD, J10RLEDD, J10SELEDD 1996
BJ10RELEUS, J10EEUS, J10ELEUS, J10RELEUS, J10REUS, J10RLEUS, J10SELEUS 1997
BJ10RHLSDA, BJ10RHSDA, J10RLSDC, J10RSDC 2006
BJ10RHLSOR, BJ10RHSOR, J10RLSOS, J10RSOS 2005
BJ10RHLSRC, BJ10RHSRC, J10RLSRD, J10RSRD 2004
BJ10RHLSTS, BJ10RHSTS, J10RLSTE, J10RSTE 2003
BJ15EEDS, BJ15ELEDS, BJ15REDS, BJ15RLEDS, J15EEDS, J15ELEDS, J15REDS, J15RELEDS, J15RLEDS, SJ15BAEDC, SJ15REDS, SJ15RLEDS 1996
BJ15RELEUC, J15EEUC, J15ELEUC, J15RELEUC, J15REUC, J15RLEUC, SJ15BAEUR 1997
HJ15KCF, HJ15KCLF, HJ15RPLW, HJ15RPW, SJ15RPLW, SJ15RPW 1997
HJ15KCLN, HJ15KCN, SJ15RPG, SJ15RPLG 1996
HJ15KCLO, HJ15KCO, SJ15RPC, SJ15RPLC 1998
J10EECC, J10ELECC, J10RECC, J10RELECC, J10RLECC, J10SELECC 1998
J10EEOE, J10ELEOE, J10RELEOE, J10REOE, J10RLEOE, J10SELEOE 1995
J10EERB, J10ELERB, J10RELERB, J10RERB, J10RLERB, J10SELERB 1994
J10EETM, J10ELETM, J10RELETM, J10RETM, J10RLETM, J10SELETM, TJ10RELETM 1993
J10ELEER, J10REER, J10RLEER, J10TEEER, J10TELEER 1999
J10ELSIM, J10EVLSIC, J10RGTSIC, J10RLGTSIC, J10RLSIM, J10RSIM, J10RVLSIC, J10RVSIC, J10TEGTSIC, J10TELSIM, J10TESIM, J10TVESIM 2001
J10ELSSA, J10EVLSSS, J10RGTSSS, J10RLGTSSS, J10RLSSA, J10RSSA, J10RVLSSS, J10RVSSS, J10TEGSSS, J10TELSSA, J10TESSA 2000
J10RLSUR, J10RSUR 2007
J15EECR, J15ELECR, J15RECR, J15RELECR, J15RLECR, SJ15BAECA 1998
J15EEOD, J15ELEOD, J15RELEOD, J15REOD, J15RLEOD 1995
J15EERE, J15ELERE, J15RELERE, J15RERE, J15RLERE 1994
J15EETB, J15ELETB, J15RELETB, J15RETB, J15RLETB 1993
J15ELEEA, J15REEA, J15RLEEA, J15TEEEA, J15TELEEA, SJ15BAEEM, SJ15RTEEM 1999
J15ELSIB, J15EVLSIC, J15RLSIB, J15RSIB, J15RVLSIC, J15RVSIC, J15TELSIB, J15TESIB, J15TVESIB, SJ15RTSIR 2001
J15ELSSM, J15EVLSSS, J15RLSSM, J15RSSM, J15RVLSSS, J15RVSSS, J15TELSSM, J15TESSM, SJ15RTSSB 2000
J15RLSDR, J15RSDR, J15RTSDC 2006
J15RLSOC, J15RSOC, J15RTSOS, J15WRLSOB, J15WRSOB 2005
J15RLSRS, J15RSRS, J15WRLSRM, J15WRSRM 2004
J15RLSTD, J15RSTD 2003
J15RLSUA, J15RSUA, J15RTSUR 2007
J15WREES, J15WRLEES 1999
J15WRLSIR, J15WRSIR 2001
J15WRLSSC, J15WRSSC 2000
SJ10REDD, SJ10RLEDD, SJ10SELEDD 1996
SJ10RPB, SJ10RPLB 1996
SJ10RPLT, SJ10RPT 1997
SJ10RPLY, SJ10RPY 1998

Information:

1. Disconnect the radiator hose from elbow (3).2. Remove two tube assemblies (2).3. Remove the bolts that hold elbow (3) to the water pump, and remove the elbow.4. Remove the bolts that hold elbow (1) to the water pump.5. Remove the bolts and retainers that hold elbow (1) to the tube assembly, and remove the elbow. 6. Remove the bolts and adapter assembly (4) from the front drive housing. 7. Remove O-ring seals (6) and (7) from adapter assembly (4).8. If necessary, remove bearing (5) from the adapter assembly. 9. Fasten a hoist and tooling (A) to water pump (8). Remove the bolts and the water pump from the front drive housing. The weight of the water pump is 25 kg (55 lb).10. Remove O-ring seal (9) from the water pump. The following steps are for installation of the Auxiliary Water Pump.11. Put O-ring seal (9) in position on the water pump. Put clean engine oil on the O-ring seal.12. Fasten a hoist and tooling (A) to water pump (8). Put the water pump in position on the front drive housing, and install the bolts that hold it. 13. If the bearing was removed from adapter assembly (4), align the hole in the bearing with the oil hole in the adapter assembly. Install the bearing with a press and tool (B). Install the bearing until it is 1.5 0.5 mm (.06 .02 in) below surface (X). The inside diameter of the bearing must be 75.000 0.055 mm (2.9528 .0022 in) after installation. 14. Put O-ring seals (6) and (7) in position on adapter assembly (4). Put clean oil on the O-ring seals.15. Put the adapter assembly in position on the front drive housing, and install the bolts that hold it. 16. Make sure the O-ring seal is in position on tube assembly (10). Put elbow (1) in position on the tube assembly, and install the retainers and bolts to hold it in place.17. Put the gasket in position between elbow (11) and the water pump, and install the bolts and nuts that hold the elbow to the water pump.18. Put the O-ring seal in position on the back of the water pump, and install elbow (3).19. Install two tube assemblies (2).20. Connect the radiator hose to elbow (3).End By:a. install air compressorDisassemble Auxiliary Water Pump
Start By:a. remove auxiliary water pump 1. Remove O-ring seals (3) and (4) from the pump housing.2. Remove the bolts and gear (2) from shaft (1). 3. Remove the bolts and adapter (5) from the pump housing. Remove the O-ring seal from adapter (5). 4. Loosen bolt (6) and the washer that hold impeller (7) to the shaft5. Use tooling (A) to loosen impeller (7) from the end of the pump shaft Remove tooling (A), bolt (6), the washer and impeller (7) from the pump shaft and housing. 6. Remove spring (9) from carbon seal assembly (10). Remove carbon seal assembly (10) from the end of shaft (8). 7. Remove the bolts that hold retainer washers (12) to the pump housing. Remove shaft (1) and washers (12) from the pump housing. 8. Remove the bolts that hold the shims and retainer washers (13) to the pump housing. Remove shaft (8), the shims and washers (13) from the pump housing.9. Remove the rubber ring and ceramic seal (11) from the pump housing. 10. Remove lip-type seal (14) from the pump housing. 11. Remove bearing (15) from the pump housing.Assemble Auxiliary Water Pump
1. Make sure the oil hole in the bearing is in alignment with the oil passage in housing (1). Use tool group (A) and a press to push the bearing in housing (1) until it is 1.5 0.5 mm (.06 .02 in) below the surface of housing (1). The inside diameter of the bearing must be 75.000 0.055 mm (2.9528 .0022 in). 2. Use tool group (A) to install the lip-type seal in housing (1). Make sure the lip of the seal is toward the bearing. Put clean engine oil on the lip of the seal. 3. Install shaft (2) in the pump housing. Install retainer washers (3), the shims and bolts to hold shaft (2) in the pump housing. 4. Put clean engine oil on the bearing in the pump housing, and install shaft (4) and retainer washers (5) over shaft (2). Install the bolts to hold retainer washers (5) to the pump housing.
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Install ceramic seal ring (6) in the rubber seal. Put clean water on the rubber seal and ceramic seal ring for lubrication. Use hand pressure and the tool (which is with the replacement seal group) to install the seal and seal ring as shown. 6. Remove the spring from carbon seal assembly (7). Put clean water on the inside diameter of the seal assembly for lubrication. Use hand pressure and the tool (which is with the replacement seal group) to push seal assembly (7) on the shaft until seal faces make light contact. 7. Install spring (8) on carbon seal assembly (7). 8. Put impeller (9) in position on the pump shaft as shown. 9. Install the bolt and washer that hold impeller (9) to the pump shaft Tighten the bolt to a torque of 38 4 N m (28 3 lbft). 10. Install O-ring seal (11) around adapter (10), and put a small amount of clean engine oil or glycerine on it.11. Put adapter (10) in position, and install the bolts to hold it to the pump housing. 12. Put gear (12) in position on shaft (4), and install the bolts to hold gear (12). 13. Install O-ring seals (13) and (14) in the pump housing, and put clean engine oil on the


Back to top