0387726 JOHNSON SHIFT LEVER ASSY


0387726 SHIFT LEVER ASSY JOHNSON 100ML79S, 115ML79R, 140ML79R, 150TL79C, 175TL79R, 200TL79A, 235TL70A, 50R79C, 55E79C, 70EL79R, 75ELR79R, 85ML79R, J100MLCSC, J115MLCIH, J115MLCSA, J140MLCIH, J140MLCSA, J150TLCIA, J150TLCSF, J175TLCIH, J175TLCSA, J200TLCIH, J200TLCSF, J235TLCIB, J235 SHIFT
0387726 SHIFT LEVER ASSY JOHNSON
Rating:
68

Buy SHIFT LEVER ASSY 0387726 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

BRP JOHNSON entire parts catalog list:

100ML79S, 100TLR79S, 100TXLR79S 1979
115ML79R, 115TL79R, 115TXL79R 1979
140ML79R, 140TL79R, 140TXL79R 1979
150TL79C, 150TXL79C 1979
175TL79R, 175TXL79R 1979
200TL79A, 200TXL79A 1979
235TL70A, 235TXL79A 1979
50R79C, 50RL79C 1979
55E79C, 55EL79C 1979
70EL79R 1979
75ELR79R, 75ER79R 1979
85ML79R, 85TL79R, 85TXL79R 1979
J100MLCSC, J100TRLCSC, J100TRXCSC 1980
J115MLCIH, J115MLCIM, J115TLCIH, J115TLCIM, J115TXCIH, J115TXCIM 1981
J115MLCSA, J115TLCSA, J115TXCSA 1980
J140MLCIH, J140MLCIM, J140TLCIH, J140TLCIM, J140TXCIH, J140TXCIM 1981
J140MLCSA, J140TLCSA, J140TXCSA 1980
J150TLCIA, J150TLCIH, J150TXCIA, J150TXCIH 1981
J150TLCSF, J150TLCSR, J150TXCSF, J150TXCSR 1980
J175TLCIH, J175TLCIM, J175TXCIH, J175TXCIM 1981
J175TLCSA, J175TLCSF, J175TXCSA, J175TXCSF 1980
J200TLCIH, J200TXCIB, J200TXCIH 1981
J200TLCSF, J200TLCSM, J200TXCSF, J200TXCSM 1980
J235TLCIB, J235TLCIH, J235TXCIB, J235TXCIH 1981
J235TLCSM, J235TXCSM 1980
J50BECIC, J50BELCIC 1981
J50ECSR, J50ELCSR 1980
J55RCIM, J55RLCIM 1981
J55RLCSA 1980
J60ECIA, J60ECIH, J60ELCIA, J60ELCIH, J60TLCIA, J60TLCIH 1981
J60ECSR, J60ELCSR 1980
J70ELCIH, J70ELCIM, J70TLCIM 1981
J70ELCSA 1980
J75ERCIH, J75ERCIM, J75ERLCIH, J75ERLCIM, J75TELCIM, J75TRLCIH 1981
J75ERCSA, J75ERLCSA, J75TRLCSA 1980
J85MLCSA, J85TLCSA, J85TXCSA 1980
J90MLCIH, J90MLCIM, J90TLCIH, J90TLCIM, J90TXCIH, J90TXCIM 1981

Information:


Illustration 1 g00845975
Typical example
(1) The chamber that is on the top of the piston must face the right side of the engine. (2) The Shibaura name that is on the inside of the piston must align with the stamped number on the connecting rod. Piston and Piston Rings
Illustration 2 g00845969
Typical example
Use a feeler gauge to measure the clearance between the piston ring groove and the piston ring. If the clearance is greater than the service limit, use a new piston ring and check the clearance.If the clearance is within the service limit, renew the piston rings. If the clearance is outside of the service limit, renew the piston. (1) Top piston ring Shape of top ring (A) Naturally aspirated ... Barrel faceTurbocharged ... Half keystoneC1.5, and C2.2 (Naturally Aspirated) Clearance between piston ring groove and top piston ring ... 0.07 to 0.11 mm (0.0028 to 0.0043 inch)Service limit for clearance of top piston ring ... 0.25 mm (0.0098 inch)Gap of top piston ring ... 0.20 to 0.35 mm (0.0079 to 0.0138 inch)Service limit for gap of top piston ring ... 1.0 mm (0.039 inch)Note: It is difficult to measure the wear of the top piston ring on the C2.2 turbocharged engines. When either the intermediate ring or the oil control ring is outside the service limit, renew all of the rings.Note: Install the letters "T" or "RN" toward the top of the piston. New top piston rings have a red identification mark. The identification mark must be on the left of the ring gap when the top piston ring is installed on an upright piston.Note: New top piston rings for the C2.2 have a yellow identification mark. The identification mark must be on the left of the ring gap when the top piston ring is installed on an upright piston.Note: The top surface of the piston ring should be equally distant from the top face of the cylinder block at all points before the piston ring end gap is measured with a feeler gauge. (2) Intermediate ring Shape of intermediate ring (B) ... TaperC1.5, C2.2, and C2.2T Clearance between piston ring groove and intermediate ring ... 0.04 to 0.08 mm (0.0016 to 0.0032 inch)Service limit for clearance of intermediate ring ... 0.25 mm (0.0098 inch)C1.5, and C2.2 gap of the intermediate ring ... 0.2 to 0.4 mm (0.0079 to 0.0157 inch)C2.2T gap of the intermediate ring ... 0.5 to 0.7 mm (0.020 to 0.023 inch)Service limit for gap of intermediate ring ... 1.2 mm (0.047 inch)Note: Install the word "Top" toward the top of the piston. New intermediate rings have a green identification mark. The identification mark must be on the left of the ring gap when the intermediate ring is installed on an upright piston.Note: The top surface of the piston ring should be equally distant from the top face of the cylinder block at all points before the piston ring end gap is measured with a feeler gauge. (3) Oil control ring C1.5, C2.2, and C2.2T Clearance between piston ring groove and oil control ring ... 0.02 to 0.06 mm (0.0008 to 0.0024 inch)Service limit for clearance of oil control ring ... 0.15 mm (0.0059 inch)Gap of oil control ring ... 0.25 to 0.50 mm (0.0098 to 0.0197 inch)Service limit for gap of oil control ring ... 1.0 mm (0.039 inch)The oil control ring has two components. The two components of the oil control ring are installed in the following order.
Spring (D)
Oil control ring (C) Note: A latch pin is used in order to hold both ends of the spring of the oil control ring in position. The ends of the spring of the oil control ring must be 180 degrees opposite the end gap of the oil control ring.Note: The top surface of the piston ring should be equally distant from the top face of the cylinder block at all points before the piston ring end gap is measured with a feeler gauge. (4) Piston C1.5, C2.2, and C2.2T Diameter of the piston skirt ... 83.948 to 83.963 mm (3.3050 to 3.3056 inch)Service limit ... 83.7 mm (3.295 inch)Clearance of the piston skirt to the cylinder wall ... 0.0380 to 0.0720 mm (0.00150 to 0.00283 inch)Service limit ... 0.25 mm (0.010 inch)Diameter of the piston pin ... 27.994 to 28.000 mm (1.1021 to 1.1024 inch)Service limit ... 27.98 mm (1.1016 inch)Clearance between the hole for the piston pin and the piston pin ... −0.001 to +0.011 mm (−0.0004 to +0.0004 inch)Service limit ... 0.02 mm (0.0008 inch)Refer to Specifications, "Cylinder Head" for the piston height for a given gasket thickness.


Parts shift JOHNSON:

0317387
 
0317387 SHIFT LEVER
50ES72C, 50ES73R, 50R79C, 55E79C, J55RLCSA, J60ECSR
0386844
 
0386844 SHIFT LEVER ASSY. , C' case
50ES75B, 50R79C, 55E76E, 55E77D, 55E78S, 55E79C
0387474
 
0387474 SHIFT LEVER & BUSHING PKG
50ES75B, 50R79C, 55E76E, 55E77D, 55E78S, 55E79C, J50BECIC, J50BECNR, J50ECSR, J55RCIM, J55RLCSA, J60ECIA, J60ECNM, J60ECSR
0320133
 
0320133 SHIFT ROD, Long
50ES75B, 50R79C, 55E76E, 55E77D, 55E78S, 55E79C, J50BECIC, J50BECNR, J50ECSR, J55RCIM, J55RLCSA, J60ECIA, J60ECNM, J60ECSR
0320132
 
0320132 SHIFT ROD, Std.
50ES75B, 50R79C, 55E76E, 55E77D, 55E78S, 55E79C, J50BECIC, J50BECNR, J50ECSR, J55RCIM, J55RLCSA, J60ECIA, J60ECNM, J60ECSR
0324362
 
0324362 SHIFT LEVER
150TL79C, 175TL79R, 200TL79A, 235TL70A, J150CXCCA, J150CXCEM, J150CXEIE, J150CXESB, J150GTLCUR, J150STLACA, J150STLCDC, J150STLCEM, J150STLCOH, J150STLCRD, J150STLCTE, J150STLEIE, J150STLESB, J150TLCDC, J150TLCIA, J150TLCNM, J150TLCOS, J150TLCRD, J15
0324407
 
0324407 SHIFT ROD
150TL79C, 175TL79R, 200TL79A, 235TL70A, J150CXCCA, J150CXCEM, J150CXEIE, J150CXESB, J150GTLCUR, J150STLACA, J150STLCDC, J150STLCEM, J150STLCOH, J150STLCRD, J150STLCTE, J150STLEIE, J150STLESB, J150TLCDC, J150TLCIA, J150TLCNM, J150TLCOS, J150TLCRD, J15
0324408
 
0324408 SHIFT ROD
150TL79C, 175TL79R, 200TL79A, 235TL70A, J150CXCCA, J150CXCEM, J150CXEIE, J150CXESB, J150TLCDC, J150TLCIA, J150TLCNM, J150TLCOS, J150TLCRD, J150TLCSF, J150TLCTB, J150TLCUR, J155WTLEIB, J155WTLENE, J175STLACM, J175STLCEB, J175STLEID, J175STLESE, J175TL
Back to top