5032986 SHIM (25X34X0.7mm) JOHNSON
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
SHIM
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- GEARS » 5032986
J10EL4SOR, J10R4SOA, J10RL4SOA, J10TBL4SOB, J10TE4SOA, J10TEL4SOA 2005
J10EL4SRC 2004
J10R4SDM 2006
J10R4SNF, J10RL4SNF, J10TE4SNF, J10TEL4SNF 2002
J10R4SR, J10RL4SR, J10TBL4SR, J10TE4SR, J10TEL4SR 2004
J10R4STC, J10RBL4STS, J10REL4STS, J10RL4STC, J10TBL4STC, J10TE4STC, J10TEL4STC 2003
J10R4SUB, J10RL4SUB 2007
J10RL4SDM 2006
J10TBL4SDE 2006
J10TBL4SUD, J10TE4SUB, J10TEL4SUB 2007
J10TE4SDM, J10TEL4SDM 2006
J15EL4SDC 2006
J15EL4SOS, J15R4SOA, J15RL4SOA, J15TE4SOA, J15TEL4SOA 2005
J15EL4SUR 2007
J15R4SDM 2006
J15R4SNF, J15RL4SNF, J15TE4SNF, J15TEL4SNF 2002
J15R4SR, J15TE4SR, J15TEL4SR 2004
J15R4STC, J15RL4STC, J15TE4STC, J15TEL4STC 2003
J15R4SUB, J15RL4SUB 2007
J15RL4SDM 2006
J15RL4SR 2004
J15TE4SDM, J15TEL4SDM 2006
J15TE4SUB, J15TEL4SUB 2007
Information:
Table 1
Valve Lash Check: Engine Stopped    
Inlet     0.38 0.10 mm (0.015 0.004 inch)    
Exhaust    
1.02 0.10 mm (0.040 0.004 inch)    If the measurement is not within tolerance, adjust the valve bridge and then adjust the valve lash.Valve Bridge Adjustment
When the head is disassembled, mark the valve bridges for the respective cylinders. Adjustment of the bridge will be necessary after grinding of the valves or other reconditioning of the cylinder head.The valve bridge must be adjusted before the valve lash is adjusted. The valve bridge can be adjusted without removal of the rocker arms and shafts.Use the following procedure to adjust the valve bridges:
Remove the valve cover.
Ensure that the No. 1 piston is at the top center (TC) position. Refer to Testing And Adjusting, "Finding the Top Center Position for the No. 1 Piston".
Work on the appropriate cylinders that are listed in Testing and Adjusting, "Crankshaft Positions for Valve Lash Setting".
Illustration 1 g00746680
(1) Ignition harness (2) Transformer
Disconnect ignition harness (1) .
Grasp transformer (2) and pull the transformer straight out of the cylinder head.
Illustration 2 g00746697
(3) Locknut (4) Adjustment screw (5) Valve bridge (6) Rocker arm
Illustration 3 g00820226
(3) Locknut (4) Adjustment screw (5) Valve bridge (6) Rocker arm (7) Bridge dowelNote: If the cylinder head is disassembled, keep the valve bridges with the respective valves. Check that bridge dowels (7) are installed to the correct height. Lubricate the bridge dowel, the bore for the bridge dowel, and the top contact surface of the valve bridge. Install the valve bridge on the dowel.
Loosen locknut (3) and adjusting screw (4) .
Press straight down on rocker arm (6) at the contact point for valve bridge (5) . Turn adjusting screw (4) clockwise until the screw just contacts the valve stem.
Tighten adjusting screw (4) for an additional 25 5 degrees in order to straighten the valve bridge onto the dowel.This also compensates for slack in the threads of the adjustment screw.
Hold adjusting screw (4) in position and tighten locknut (3) to 47 9 N m (35 7 lb ft).
Ensure that the valve lash is correct. Refer to "Valve Lash Check".
Install transformer (2) .
Connect ignition harness (1) .
Install the valve cover.Valve Lash Adjustment
The valve bridge must be adjusted before the valve lash is adjusted.
Ensure that the No. 1 piston is at the top center (TC) position. Refer to Testing And Adjusting, "Finding the Top Center Position for the No. 1 Piston".
Work on the appropriate cylinders that are listed in Testing and Adjusting, "Crankshaft Positions for Valve Lash Setting".
Illustration 4 g00769478
(1) Locknut (2) Adjustment screw (3) Rocker arm (4) Wear seat
Loosen locknut (1) and adjusting screw (2) .
Insert the appropriate feeler gauge between rocker arm (3) and wear seat (4) . Refer to Table 3.
Table 2
Valve Lash Setting: Engine Stopped    
Inlet    
0.38 0.10 mm (0.015 0.004 inch)    
Exhaust    
1.02 0.10 mm (0.040 0.004 inch)    
Hold adjusting screw (2) in place and tighten locknut (1) to a torque of 30 4 N m (22 3 lb ft).
Verify that the setting is correct.
Remove the timing bolt from the flywheel housing. Rotate the crankshaft for 360 degrees. Install the timing bolt in the flywheel housing.
With the No. 1 piston in the top center of the opposite stroke, perform Steps 1 through 7 for the remaining cylinders.
Remove the timing bolt from the flywheel housing.
Parts shim JOHNSON:
5032968
5032968 SHIM (20X34X1.2mm)
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
5032967
5032967 SHIM (20X34X1.1mm)
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
5032984
5032984 SHIM (20X34X0.9mm)
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
5032982
5032982 SHIM (20X34X0.7mm)
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
5032969
5032969 SHIM (20X34X1.3mm)
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
5032983
5032983 SHIM (20X34X0.8mm)
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
5032985
5032985 SHIM (20X34X1.0mm)
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD
5032988
5032988 SHIM (25X34X0.9mm)
J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SDC, J15EL4SOS, J15EL4SUR, J15R4SDM, J15R4SNF, J15R4SR, J15R4STC, J15R4SUB, J15RL4SDM, J15RL4SR, J15TE4SD