5033978 JOHNSON SHIM (70X95X0.6mm)


5033978 SHIM (70X95X0.6mm) JOHNSON BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, J140CX4SOR, J140CX4STS, J140PL4SOR, J140PL4STS, J140PX4SOR SHIM
5033978 SHIM (70X95X0.6mm) JOHNSON
Rating:
103

Buy SHIM (70X95X0.6mm) 5033978 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

BRP JOHNSON entire parts catalog list:

BJ140CX4DR, J140CX4SDA 2006
BJ140CX4SRS, J140CX4SRC 2004
BJ140L4SDR, BJ140X4SDR, J140PL4SDA, J140PX4SDA 2006
BJ140PL4SRS, BJ140PX4SRS, J140PL4SRC, J140PX4SRS 2004
J140CX4SOR 2005
J140CX4STS 2003
J140PL4SOR 2005
J140PL4STS, J140PX4STS 2003
J140PX4SOR 2005

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 9U-6238 Guide Bolt 2
C 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure that there is no debris in the cylinder bores.
Illustration 1 g00942889
Install cylinder head gasket (3) on dowels (4) on top of the cylinder block. The cylinder head gasket (3) is stamped "FRONT TOP". Do not use any sealant or compound on the cylinder head gasket.
Install Tooling (B) in the cylinder block in Hole (X).
Illustration 2 g00942891
Install Tooling (A) and a suitable lifting device to cylinder head (2). The weight of the cylinder head is approximately 61 kg (135 lb).
Install cylinder head (2) on the cylinder block. Note: Ensure that the cylinder head is positioned on dowels (4).
Remove Tooling (A). Remove the guide bolts.
Illustration 3 g00942928
Clean the threads of the cylinder head bolts. Inspect the cylinder head bolts. Note: Do Not use bolts if there is any visual reduction in the diameter of the Threads (Y) that has not been engaged with the cylinder block. Use a straight edge to check the bolts.
Lubricate the threads and the shoulder of the cylinder head bolts with clean engine oil before installation.
Install bolts (1) on cylinder head (2). Note: The short bolts are installed in holes that are marked with an "S" (5, 6, 11, 12, 16, 17, 21, 22, 26, 27, 31, and 32).Note: The medium bolts are installed in holes that are marked with an "M" (1, 2, 3, 4, 7, 8, 9, 10, 13, 14, 15, 18, 19, 20, 23, 25, 28, and 30).Note: The long bolts are installed in holes that are marked with an "L" (24 and 29).
Illustration 4 g00893273
Tighten bolt (1) through bolt (32) in numerical order to a torque of 110 N m (80 lb ft). Refer to Illustration 4.
Tighten bolt (1) through bolt (32) again in numerical order to a torque of 110 N m (80 lb ft). Refer to Illustration 4.
Illustration 5 g00946758
Use Tooling (C) to achieve the correct final torque. Note: If Tooling (C) is not used, place an index mark on each bolt.
Tighten the cylinder head bolts in numerical order. Refer to Illustration 4.
Turn the bolts that are marked with an "S" an additional 150 degrees.
Turn the bolts that are marked with an "M" an additional 180 degrees.
Turn the bolts that are marked with an "L" an additional 210 degrees.
Connect the harness assembly for the coolant temperature sensor. End By:
Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet Manifold - Install".
Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
Install the air inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Install".
Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".


Parts shim JOHNSON:

5032570
SHIM (T:1.1mm)
5032570 SHIM (T:1.1mm)
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140L4SDR, BJ140PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J140PL4SOR, J140PL4STS, J140PX4SOR, J60PL4SNF
5033884
 
5033884 SHIM, TAPPET (T:2.83mm)
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ25R4SDS, BJ25R4SUC, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J140CX4SOR, J140CX4STS, J140PL4SOR, J140PL4STS, J140PX4SOR, J90PL4SOR
5033890
 
5033890 SHIM, TAPPET (T:2.98mm)
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J140CX4SOR, J140CX4STS, J140PL4SOR, J140PL4STS, J140PX4SOR, J90PL4SOR
5033885
 
5033885 SHIM, TAPPET (T:2.85mm)
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J140CX4SOR, J140CX4STS, J140PL4SOR, J140PL4STS, J140PX4SOR, J90PL4SOR
5033891
 
5033891 SHIM, TAPPET (T:3.00mm)
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J140CX4SOR, J140CX4STS, J140PL4SOR, J140PL4STS, J140PX4SOR, J90PL4SOR
5033670
 
5033670 SHIM, TAPPET (T:2.18mm)
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J140CX4SOR, J140CX4STS, J140PL4SOR, J140PL4STS, J140PX4SOR, J90PL4SOR
5033676
 
5033676 SHIM, TAPPET (T:2.33mm)
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J140CX4SOR, J140CX4STS, J140PL4SOR, J140PL4STS, J140PX4SOR, J90PL4SOR
5033980
 
5033980 SHIM (70X95X0.75mm)
BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, J140CX4SOR, J140CX4STS, J140PL4SOR, J140PL4STS, J140PX4SOR
Back to top