5034801 JOHNSON SHIM (T:0.50mm)


5034801 SHIM (T:0.50mm) JOHNSON BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS SHIM
5034801 SHIM (T:0.50mm) JOHNSON
Rating:
93

Buy SHIM (T:0.50mm) 5034801 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$29.59
 

30-07-2024

Amazon.com
KEO 50348-01 3 Flute Center Reamer, High Speed Steel, 82 Degree Cutting Angle, Right Hand Cut, 3/4" Body Diameter
KEO Cutters Product Type:Cutting Tools || Item Package Dimension:12.192 Cm L X 8.636 Cm W X 5.842 Cm H || Item Package Quantity:1 || Country Of Origin: United States
Number on catalog scheme: 7
 

Information:

Installation Information for Fastener Group That Uses Hex Head Bolts
Illustration 1 g01091089
Typical example
Top view with compression brake
Note: The installation of the compression brake must be completed prior to adjusting the valve lash, the injector lash, or the compression brake's slave piston lash.
Place the compression brake over the taperlock studs and onto the engine.
Install the hard washers and four bolts 1, 2, 3 and 4 through the engine brake housing group. Finger tighten the bolts.
Install the hard washer and nut 5. Finger tighten the nut. Note: Use the torque sequence that is shown in Illustration 1.
Tighten four bolts to 50 7 N m (37 5 lb ft). Turn the bolts through an additional 90 5 degrees.
Tighten the nut to 50 7 N m (37 5 lb ft). Turn the nut through an additional 90 5 degrees.
Illustration 2 g01640895
Typical example
Top view with compression brake
Before the compression brake's slave piston is allowed to contact the bottom of the housing bore, the free running torque of slave piston adjustment screws (1) must not exceed the following value. ... 3 N m (27 lb in) (2) Final torque for two full nuts ... 34 5 N m (25 4 lb ft) (3) Final torque for three taperlock studs ... 65 10 N m (48 7 lb ft) (4) Final torque for the solenoid ... 20 N m (15 lb ft)Slave Piston Lash Settings
Note: Refer to Testing and Adjusting, "Slave Piston Lash - Adjust" for the complete procedure for adjusting the slave piston lash.
Prior to adjusting the lash setting for the engine compression brake, check the identification plate that is on the compression brake's casting in order to determine the model that is installed on your engine. You must have this model number and the engine's serial number prefix in order to determine the lash setting for your engine.
Table 1
Slave Piston Lash Setting
Jake Brake Compression Brakes
Serial Number Prefix and Model Number(1) Horsepower Rating Slave Piston Lash Setting
BXS1-UP
Jake Brake 340C All ratings 0.89 0.08 mm (0.035 0.003 inch)
BXS1-UP
Jake Brake 340E All ratings 0.84 0.08 mm (0.033 0.003 inch)
(1) Check the identification plate that is on the compression brake's casting in order to determine the model that is installed on your engine.Note: The slave piston lash setting is specific to the model number of the compression brake and to the serial number prefix of the engine. Use these settings only for the compression brakes and the serial number prefixes that are specified in the table.Pacbrake Compression Brake
Note: There is a fastener group that utilizes 12 point bolts for the installation of the compression brake to the cylinder head. If your compression brakes utilize 12 point bolts, refer to Specifications, "Compression Brake" for this type of fastener group.Installation Information for Fastener Group That Uses Hex Head Bolts
Illustration 3 g01098169
Typical example
Top view with compression brake
Note: The installation of the compression brake must be completed prior to adjusting the valve lash, the injector lash, or the compression brake's slave piston lash.
Place the compression brake over the taperlock studs and onto the engine.
Install the hard washers and four bolts 1, 2, 3 and 4 through the engine brake housing group. Finger tighten the four bolts.
Install the hard washer and the nut 5. Finger tighten the nut. Note: Use the torque sequence that is shown in Illustration 3.
Tighten four bolts to 50 7 N m (37 5 lb ft). Turn the bolts through an additional 90 5 degrees.
Tighten the nut to 50 7 N m (37 5 lb ft). Turn the nut through an additional 90 5 degrees.
Illustration 4 g01640896
Typical example
Top view with compression brake
Before the compression brake's slave piston is allowed to contact the bottom of the housing bore, the free running torque of slave piston adjustment screws (5) must not exceed the following value. ... 3 N m (27 lb in) (6) Final torque for two full nuts ... 34 5 N m (25 4 lb ft) (7) Final torque for three taperlock studs ... 65 10 N m (48 7 lb ft)Slave Piston Lash Settings
Table 2
Slave Piston Lash Setting
Pacbrake Compression Brakes
Serial Number Prefix Model Designation Slave Piston Lash Setting
BXS1-UP P39E 0.71 0.08 mm (0.028 0.003 inch)


Parts shim JOHNSON:

5034921
 
5034921 SHIM, TAPPET (T:2.18mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034927
 
5034927 SHIM, TAPPET (T:2.33mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034924
 
5034924 SHIM, TAPPET (T:2.25mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034930
 
5034930 SHIM, TAPPET (T:2.40mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034947
 
5034947 SHIM, TAPPET (T:2.83mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034953
 
5034953 SHIM, TAPPET (T:2.98mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034811
SHIM (75X100X0.8mm)
5034811 SHIM (75X100X0.8mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5036124
 
5036124 SHIM (75X100X0.55mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200PX4SOC, J225CX4SOC, J225PX4SOC
Back to top