5034804 SHIM (T:0.65mm) JOHNSON
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
SHIM
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
BJ200X4SDC 2006
BJ225CX4DC 2006
BJ225X4SDC 2006
BJ200CX4O, J200CX4SOC 2004,2005
J200CX4SRS 2004
BJ200X4SO, J200PX4SOC 2004,2005
J200PX4SRS 2004
BJ225CX4O, J225CX4SOC, J225CZ4SOS 2004,2005
J225CX4SRS 2004
BJ225X4SO, J225PX4SOC, J225PZ4SOS 2004,2005
J225PX4SRS 2004
Information:
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
If the fuel system runs out of fuel or if air is introduced into the fuel system the following procedure may be followed.
Turn the ignition switch to the "OFF" position.
Fill the fuel tank (s) with clean diesel fuel.
Illustration 1 g01451302
(1) Fuel priming pump
(2) Air purge
(3) Priming valve (If Equipped)
Turn the priming valve (3) (If Equipped) to the "Closed (Prime)" position in order to prime the fuel system.
Purging air from the fuel system requires the air purge to be opened three full turns. Open air purge (1). Do not remove the screw.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine for 30 seconds. Use a suitable container to catch the fuel while you crank the engine. Allow the starting motor to cool for 2 minutes. Note: Most of the air should be purged from the system after four or five cranking cycles.
Repeat Step 5 until the engine starts and runs. If the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly.
Observe air purge (2). When a small drop of fuel appears at the threads of the air purge, close and tighten air purge (2). Note: Failure to tighten all fittings could result in serious fuel leaks.
After the engine has operated smoothly for 30 seconds, turn the priming valve (3) to the "Open (Run)" position. Note: Shortened injector life may occur if the priming valve (3) is left in the "Closed (Prime)" position.
Clean any residual fuel from the engine components.
Once the engine runs smoothly, stop the engine. Turn the ignition switch to the OFF position. Note: You may use the hand priming pump for the fuel filter (if equipped) instead of cranking the engine and running the engine. Perform the following procedure when the hand priming pump is used:
Illustration 2 g01451302
(1) Fuel priming pump
(2) Air purge
(3) Priming valve (If Equipped)
Turn the priming valve (3) (If Equipped) to the "Closed (Prime)" position in order to prime the fuel system.
Purging air from the fuel system requires the Air purge (1) for the fuel filter to be opened three full turns. Open air purge (1). Do not remove the screw.
While you operate the hand priming pump, observe the air purge (2). When a small drop of fuel appears at the threads of the air purge, close and tighten the air purge (2). Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components.
Continue to operate the fuel priming pump (1) until a strong resistance is felt. Listen for an audible click from the fuel manifold. The click will indicate that the valve has opened and the fuel system is pressurized. Lock the fuel priming pump.
Do not crank the engine for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking again.
Crank the engine. If the engine starts but the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly. Note: If the engine will not start, further priming is necessary. If the engine starts but the engine continues to misfire or smoke, further priming is necessary.
After the engine has operated smoothly for 30 seconds, turn the priming valve (3) to the "Open (Run)" position. Note: Shortened injector life may occur if the priming valve (3) is left in the "Closed (Prime)" position.
Parts shim JOHNSON:
5034921
5034921 SHIM, TAPPET (T:2.18mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034927
5034927 SHIM, TAPPET (T:2.33mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034924
5034924 SHIM, TAPPET (T:2.25mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034930
5034930 SHIM, TAPPET (T:2.40mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034947
5034947 SHIM, TAPPET (T:2.83mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034953
5034953 SHIM, TAPPET (T:2.98mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034811
5034811 SHIM (75X100X0.8mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5036124
5036124 SHIM (75X100X0.55mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200PX4SOC, J225CX4SOC, J225PX4SOC