5034924 JOHNSON SHIM, TAPPET (T:2.25mm)


5034924 SHIM, TAPPET (T:2.25mm) JOHNSON BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS SHIM
5034924 SHIM, TAPPET (T:2.25mm) JOHNSON
Rating:
83

Buy SHIM, TAPPET (T:2.25mm) 5034924 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

BRP JOHNSON entire parts catalog list:

BJ200CX4DC 2006
BJ200X4SDC 2006
BJ225CX4DC 2006
BJ225X4SDC 2006
BJ200CX4O, J200CX4SOC 2004,2005
J200CX4SRS 2004
BJ200X4SO, J200PX4SOC 2004,2005
J200PX4SRS 2004
BJ225CX4O, J225CX4SOC, J225CZ4SOS 2004,2005
J225CX4SRS 2004
BJ225X4SO, J225PX4SOC, J225PZ4SOS 2004,2005
J225PX4SRS 2004

Information:

Note: Do not use the belt tension charts for belts with tensioners that are spring loaded.
Table 1
Belt Tension Chart    
Size of Belt     Width of Belt     Gauge Reading     Kent-Moore Gauge Numbers    
Belt Tension
"Initial" (1) Belt Tension
"Used" (2) (3)     Number of the Old Gauge     Number of the New Gauge    
3/8    
10.72 mm (0.422 inch)    
534 111 N (120 25 lb)    
400 22 N (90 5 lb)     BT-33-97     BT 3397    
1/2    
13.89 mm (0.547 Inch)    
578 111 N (130 25 lb)    
445 44 N (100 10 lb)     BT-33-97     BT 3397    
5V    
15.88 mm (0.626 Inch)    
712 111 N (160 25 lb)    
445 44 N (100 10 lb)     BT-33-72C     BT 3372C    
11/16    
17.48 mm (0.688 Inch)    
712 111 N (160 25 lb)    
445 44 N (100 10 lb)     BT-33-72C     BT 3372C    
3/4    
19.05 mm (0.750 Inch)    
712 111 N (160 25 lb)    
445 44 N (100 10 lb)     BT-33-72C     BT 3372C    
15/16    
23.83 mm (0.938 Inch)    
712 111 N (160 25 lb)    
445 44 N (100 10 lb)     BT-33-77     BT 3372C    
8PK    
27.82 mm (1.095 inch)    
1068 111 N (240 25 lb)    
890 44 N (200 10 lb)     BT-33-109     BT 33109    
6PK    
20.94 mm (0.824 Inch)    
801 111 N (180 25 lb)    
667 44 N (150 10 lb)     BT-33-109     BT 33109    
Measure the tension of the belt that is farthest from the engine.    
( 1 ) Belt tension "Initial" is for a new belt.
( 2 ) Belt tension "Used" is for a belt that has operated for 30 minutes or more of operation at the rated speed.
( 3 ) If a belt falls below the "Used" belt tension, the belt should be tightened again to the high side of the "Used" belt tension.
Table 2
DAYCO Supplied Belts Only    
Size of Belt     Belt Tension
"Initial"     Belt Tension
"Used" (4)    
0.380 (V-Belt)    
623 22 N (140 5 lb)    
245 - 534 N (100 5 lb)    
0.440 (V-Belt)    
667 22 N (150 5 lb)    
245 - 534 N (100 5 lb)    
0.500 (V-Belt)    
712 22 N (160 5 lb)    
245 - 534 N (100 5 lb)    
0.600 (V-Belt)    
779 22 N (175 5 lb)    
245 - 534 N (100 5 lb)    
0.660 (V-Belt)    
890 22 N (200 5 lb)    
245 - 534 N (100 5 lb)    
0.790 (V-Belt)    
890 22 N (200 5 lb)    
245 - 534 N (100 5 lb)    
4 - RIB PVK    
623 22 N (140 5 lb)    
267 - 445 N (90 5 lb)    
5 - RIB PVK    
779 22 N (175 5 lb)    
334 - 556 N (100 5 lb)    
6 - RIB PVK    
934 22 N (210 5 lb)    
400 - 667 N (130 5 lb)    
8 - RIB PVK    
1157 22 N (260 5 lb)    
534 - 890 N (180 5 lb)    
10 - RIB PVK    
1557 22 N (350 5 lb)    
667 - 1112 N (230 5 lb)    
12 - RIB PVK    
1869 22 N (420 5 lb)    
800 - 1335 N (270 5 lb)    
15 - RIB PVK    
2336 22 N (525 5 lb)    
1000 - 1669 N (350 5 lb)    


Parts shim JOHNSON:

5034921
 
5034921 SHIM, TAPPET (T:2.18mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034927
 
5034927 SHIM, TAPPET (T:2.33mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034930
 
5034930 SHIM, TAPPET (T:2.40mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034947
 
5034947 SHIM, TAPPET (T:2.83mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034953
 
5034953 SHIM, TAPPET (T:2.98mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5034811
SHIM (75X100X0.8mm)
5034811 SHIM (75X100X0.8mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
5036124
 
5036124 SHIM (75X100X0.55mm)
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200PX4SOC, J225CX4SOC, J225PX4SOC
5035280
 
5035280 *SHIM (50X62X1.6mm)
BJ200X4SDC, BJ225X4SDC, J200PX4SOC, J200PX4SRS, J225PX4SOC, J225PX4SRS
Back to top