0325382 JOHNSON SOUND BLANKET,Side

Table 1
Diagnostic Codes Table
Description Conditions which Generate this Code System Response
336-2 Incorrect ECS Switch inputs The inputs from the start/run/stop switch are in a different state. The code is logged. The Electronic Control Module (ECM) receives two input signals from the start/run/stop switch. The two input signals should have the same logic level. If two different signals are detected during the powerup, the ECM will determine that one of the signals is incorrect. The duplication of the signals permits the ECM to know if there is a problem in the wiring.When both of the input signals are high or open, the ECM assumes that the start/run/stop switch is in the STOP position. When both of the input signals are low or shorted to the −Battery terminal, the ECM assumes that the start/run/stop switch is in the START position. After the start/run/stop switch is turned to the START position, the ECM will initiate the starting sequence. The ECM will energize the prelube system if the prelube system is available and activated. After the prelube cycle is completed the ECM will energize the starting solenoids for the starting motors. If both of the signals go high or open while the engine is running, the engine will stop.If the engine is running and one of the inputs from the start/run/stop switch changes states, the ECM will ignore the inputs from the start/run/stop switch until power is cycled to the ECM. If this occurs, you must use the emergency stop switch or you must disconnect the power to the ECM in order to shut down the engine.If the inputs from the start/run/stop switch are in opposite states at the beginning of a crank cycle, the ECM will not initiate the crank cycle. If this condition occurs, the engine may be started by using the manual crank switch. If you start the engine with the manual crank switch, you must use the emergency stop switch or you must disconnect the power to the ECM in order to shut down the engine. A diagnostic code will be logged and a diagnostic code will be active for this problem. The diagnostic code for this problem will be active until the ECM is powered down.
Illustration 1 g01229789
Schematic for the start/run/stop switch
Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove electrical power from the ECM.
Illustration 2 g01232964
Location of the connectors for the start/run/stop switch
(1) J1/P1 ECM connectors
(2) Customer Connector
Thoroughly inspect connectors (1) and (2). Inspect all of the other connectors for the circuit. Refer to Troubleshooting, "Inspecting Electrical Connectors" for details.
Illustration 3 g01232956
Terminal locations at the P1 ECM connector
(P1-5) Digital return
(P1-21) Start/Run/Stop switch 1
(P1-22) Start/Run/Stop switch 2
Illustration 4 g01232961
Terminal locations at the customer connector
(Terminal 9) Digital return
(Terminal 23) Start/Run/Stop switch 1
(Terminal 24) Start/Run/Stop switch 2
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the allen head screw for each of the ECM connectors for the proper torque. Refer to Troubleshooting, "Inspecting Electrical Connectors" for the correct torque values.
Check the harness and the wiring for abrasion and for pinch points. Expected Result:All connectors, pins, and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion, and of pinch points.Results:
OK - The connectors and wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Status of the Start/Run/Stop Switch on Caterpillar Electronic Technician (ET)
Restore electrical power to the ECM.
Connect Cat ET to the service tool connector.
Turn the start/run/stop switch to the STOP position.
Monitor the parameter for the start/run/stop switch onCat ET.
Turn the start/run/stop switch to the START position.
Monitor the parameter for the start/run/stop switch onCat ET.
Turn the start/run/stop switch to the STOP position. Expected Result:The parameter for the switch reads "OFF" when the start/run/stop switch is turned to the STOP position. The parameter for the switch reads "ON" when the start/run/stop switch is turned to the START position.Results:
OK - The parameter for the switch is correct in both the STOP and START positions.Repair: The switch is functioning correctly. Reset the system and check for any active diagnostic codes. If the problem is intermittent, refer to Troubleshooting, "Inspecting Electrical Connectors".STOP
Not OK - The parameter for the switch is not correct in either the STOP or the START positions. Proceed to Test Step 3.Test Step 3. Check the Wiring for an Open Circuit
Disconnect the main power.
Disconnect the ECM connector J1/P1.
Note the location of the wires on the start/run/stop switch. Remove the wires from the start/run/stop switch.
Install a wire jumper between the wire 998-BR(Brown) and the wires F716-WH(White) and F717-YL(Yellow) at the start/run/stop switch.
Measure the resistance between P1-21 and P1-5 at the ECM connector.
Measure the resistance between P1-22 and P1-5 at the ECM connector P1.
Remove the wire jumper. Expected Result:Each resistance measurement indicated a short circuit.Results:
OK - Each resistance measurement indicated a short circuit. Proceed to Test Step 4.
Not OK -