0341529 JOHNSON SOUND BLANKET, Stbd.


0341529 SOUND BLANKET, Stbd. JOHNSON BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, HJ20CREDA, HJ25FPO, HJ25FPV, HJ25RLEDA, HJ30REDE, J20CREOR, J25JREDC, J25JREEM, J25JREOS, J25JRSIE, J25JRSSB, J25REOR, J25RLSNF, J25RLSOA, J SOUND
0341529 SOUND BLANKET, Stbd. JOHNSON
Rating:
78

Buy SOUND BLANKET, Stbd. 0341529 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 13
 

BRP JOHNSON entire parts catalog list:

BJ20SRECB, BJ20SRLECB 1998
BJ20SREDA, BJ20SRLEDA 1996
BJ20SREUM, BJ20SRLEUM, J20CREUM, J20CRLEUM 1997
BJ25BAECM, BJ25BALECM, J25JRECA, J25RECB, J25RLECB, SJ25RDECA 1998
BJ25BAEDR, BJ25BALEDR, BJ25BREDC, BJ25BRLEDC, HJ25RAEDA, SJ25RDEDC 1996
BJ25BAEUA, BJ25BALEUA, HJ25RAEUM, J25JREUR, J25REUM, J25RLEUM, SJ25RDEUR 1997
BJ30BAECS, BJ30BALECS 1998
BJ30BAEDE, BJ30BALEDE 1996
BJ30BAEEC, BJ30BAEEN, J30REEC, J30REEN, J30RLEEC, J30RLEEN 1999
BJ30BAEUD, BJ30BALEUD, J30REUD, J30RLEUD 1997
HJ20CREDA, HJ20CRLEDA, J20CREDA, J20CRLEDA 1996
HJ25FPO, HJ25RSLO, J25RWEDC, J25RWLEDC 1996
HJ25FPV, HJ25RLSV, J25RWEUR, J25RWLEUR, SJ25RPLV, SJ25RPV 1997
HJ25RLEDA, J25REDA, J25RLEDA, SJ25REDA, SJ25RLEDA 1996
HJ30REDE, HJ30RLEDE, J30REDE, J30RLEDE, SJ30REDE, SJ30RLEDE 1996
J20CREOR, J20CRLEOR 1995
J25JREDC 1996
J25JREEM, J25JREEN, J25REEB, J25REEN, J25RLEEB, J25RLEEN, SJ25RDEEM, SJ25RDEEMN, SJ25RTEEM 1999
J25JREOS 1995
J25JRSIE, J25RLSID, J25RSID, J25RVLSID, J25RVSID, SJ25RTSIE 2001
J25JRSSB, J25RLSSE, J25RSSE, SJ25RTSSB 2000
J25REOR, J25RLEOR 1995
J25RLSNF, J25RSNF 2002
J25RLSOA, J25RSOA 2005
J25RLSRR, J25RSRR 2004
J25RLSTC, J25RSTC 2003
J25RTSOS 2005
J25RWEOS, J25RWLEOS 1995
J25WRLSOB, J25WRSOB 2005
J25WRLSRM, J25WRSRM 2004
J30REOB, J30RLEOB 1995
J30RLSIA, J30RSIA, J30RVLSIA, J30RVSIA 2001
J30RLSNF, J30RSNF 2002
J30RLSOD, J30RSOD 2005
J30RLSRE, J30RSRE 2004
J30RLSSR, J30RSSR 2000
J30RLSTB, J30RSTB 2003
SJ35REDE, SJ35RLEDE 1996

Information:


Table 1
Example    
Reading     °C     °F    
Coolant Temperature     15 °C     59 °F    
Inlet Manifold Air Temperature     10 °C     50 °F    
Sum (1)     25 °C     109 °F    
( 1 ) The sum cannot be directly converted. The direct conversion of 25 °C is 77 °F.
Illustration 1 g00964120
Schematic
Illustration 2 g01116699
P2 ECM connector (P2-9) Air inlet heater - (P2-12) Air inlet heater +Test Step 1. Inspect Electrical Connectors and Wiring
Thoroughly inspect the J501/P501 air inlet heater relay connector and the J2/P2 ECM connector. Inspect the terminal connections on the air inlet heater relay and the air inlet heater. Refer to Troubleshooting, "Electrical Connectors-Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the air inlet heater.
Check the ECM connector (allen head screw) for the proper torque of 6 1 N m (55 9 lb in).
Check the harness and wiring for abrasion and for pinch points from the air inlet heater back to the ECM and from the air inlet heater back to the battery.Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector.
Check for active diagnostic codes on Cat ET.Expected Result:A 617-05 or 617-06 diagnostic code is active for the air inlet heater relay.Results:
617-05 (Open) is Active - The ECM detects an open circuit (low current) between the relay and the ECM. Proceed to Test Step 3.
617-06 (Short) is Active - The ECM detects a short circuit (high current) between the relay and the ECM. Proceed to Test Step 4.
No Active Diagnostic Codes - There are no active diagnostic codes for the air inlet heater. Proceed to Test Step 5.Test Step 3. Check for an Open Circuit to the Relay
Disconnect the signal wires (small terminals) from the air inlet heater relay.
Install a test lamp across the wires for the relay.
Start the "Air Inlet Heater Override" on Cat ET and observe the test lamp.Note: Do not leave the "Air Inlet Heater Override" ON. Avoid unnecessary cycling of the air inlet heater in order to prevent the battery from discharging. The "Air Inlet Heater Override" has a one minute timer that disables the test when the time expires.
Stop the "Air Inlet Heater Override" and turn the keyswitch to the OFF position.Expected Result:The test lamp turned on while the override was active.Results:
OK - The open circuit is in the relay.Repair: Replace the relay and clear the diagnostic code.Verify that the repair eliminates the problem.STOP
Not OK - The open circuit is in one of the wires for the relay between the relay and the ECM.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 4. Check for a Short Circuit to the Relay
Disconnect the signal wires (small terminals) from the air inlet heater relay.
Turn the keyswitch to the ON position and check for active diagnostic codes on Cat ET.
Turn the keyswitch to the OFF position.Expected Result:The short circuit diagnostic code (617-06) changed to an open circuit diagnostic code (617-05) when the signal wires to the relay were disconnected.Results:
OK - The short circuit is in the relay.Repair: Replace the relay and clear the diagnostic codes.Verify that the repair eliminates the problem.STOP
Not OK - The short circuit is in one of the wires for the relay between the relay and the ECM.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 5. Check for Battery Voltage to the Relay
Connect a test lamp between the +Battery side of the air inlet heater relay and engine ground.Expected Result:The test lamp turns ON.Results:
OK - Battery voltage is reaching the relay. Proceed to Test Step 6.
Not OK - Battery voltage is not reaching the relay.Repair: Ensure that the circuit breaker is not tripped. Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 6. Check for Voltage Output at the Relay
Connect a test lamp between the output terminal of the air inlet heater relay and engine ground.
Observe the test lamp. The test lamp should be off, since the relay is not energized. If the test lamp is on, ensure that the test lamp is connected to the output side of the terminal.
Turn the keyswitch to the ON position.
Run the "Air Inlet Heater Override" on Cat ET and observe the test lamp.Note: Do not leave the "Air Inlet Heater Override" On. Avoid unnecessary cyc


Parts sound JOHNSON:

0341527
 
0341527 SOUND BLANKET, Top
BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, HJ20CREDA, HJ25FPO, HJ25FPV, HJ25RLEDA, HJ30REDE, J20CREOR, J25JREDC, J25JREEM, J25JREOS, J25JRSIE, J25JRSSB, J25REOR, J25RLSNF, J25RLSOA, J
0341528
 
0341528 SOUND BLANKET, Port
BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, HJ20CREDA, HJ25FPO, HJ25FPV, HJ25RLEDA, HJ30REDE, J20CREOR, J25JREDC, J25JREEM, J25JREOS, J25JRSIE, J25JRSSB, J25REOR, J25RLSNF, J25RLSOA, J
0341530
 
0341530 SOUND BLANKET, Front
BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, HJ20CREDA, HJ25FPO, HJ25FPV, HJ25RLEDA, HJ30REDE, J20CREOR, J25JREDC, J25JREEM, J25JREOS, J25JRSIE, J25JRSSB, J25REOR, J25RLSNF, J25RLSOA, J
Back to top