0345773 SOUND BLANKET, Port JOHNSON
BJ200CXEEB, BJ200CXSSE, BJ225CXEEC, BJ225CXSSR, J225HPLEEN, J225HPLSSC, J250CXEEN, J250CXSSS
SOUND
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- ENGINE COVER » 0345773
BJ225CXEEC, BJ225CXEEN, BJ225PLEEC, BJ225PLEEN, BJ225PXEEC, BJ225PXEEN, J225CXEEC, J225CXEEN, J225HPLEEN, J225HPLEES, J225PLEEC, J225PLEEN, J225PXEEC, J225PXEEN 1999
BJ225CXSSR, BJ225PLSSR, BJ225PXSSR, BJ225VCSSS, BJ225VXSSS, J225CXSSR, J225HGLSSC, J225HPLSSC, J225PLSSR, J225PXSSR, J225VCXSSS, J225VXSSS, RJ225CXSSS, RJ225HGSSC, RJ225HLSSC, RJ225PLSSR, RJ225PXSSR, RJ225VXSSS 2000
J225HPLEEN, J225HPLEES 1999
J225HPLSSC 2000
J250CXEEN, J250CXEES, J250CZEEN, J250CZEES, J250PXEEN, J250PXEES, J250PZEEN, J250PZEES 1999
J250CXSSS, J250CZSSC, J250PXSSC, J250PZSSC, J250VCXSSS, J250VCZSSS, J250VXSSS, J250VZSSS, RJ250CXSSS, RJ250VXSSS, RJ250VZSSS 2000
Information:
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     150-3992     Timing Pin (1)     1    
150-3993 Timing Pin (2)     1    
B     171-1085     Tamper Resistant Tool Gp     1    
( 1 ) Tool (A) is required in order to remove Bosch fuel injection pumps.
( 2 ) Tool (A) is required in order to remove Delphi (Lucas) and Stanadyne fuel injection pumps.Start By:
Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Ensure that the No. 1 cylinder is at the top center position on the compression stroke. Refer to the Testing and Adjusting, "Fuel System" topic for additional information.
Illustration 1 g00808245
Loosen locking screw (2) (if equipped) until locking spacer (1) moves freely. Move locking spacer (1) into position (B). Tighten locking screw (2) to a torque of 10 N m (7 lb ft).
Illustration 2 g00808370
Typical exampleNote: Do not remove hub nut (4) from the shaft of the fuel injection pump. The hub of the fuel injection pump is installed in the correct position from the factory in order to ensure proper timing. If hub nut (4) is removed and the hub is removed, the hub will need to be accurately installed on the shaft of the fuel injection pump by the use of special equipment. Refer to your Caterpillar Dealer for more information.Note: Do not release torx screws (5) (if equipped). If the torx screws are released and the timing plate is moved, the timing position that is set at the factory will be lost. If the torx screws are released, the No. 1 cylinder must be set to the top center position on the compression stroke before the torx screws are tightened.
Slowly rotate the crankshaft until hole (6) in the timing gear and hole (7) in the hub are in alignment with hole (8) in the fuel injection pump body.Note: The location of Tool (A) for Bosch fuel injection pumps will be located toward the top of the fuel injection pump. The location of Tool (A) for Delphi (Lucas) and Stanadyne fuel injection pumps will be located toward the bottom of the fuel injection pump.
Install Tool (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tool (A) into position in hole (8) in the fuel injection pump body. If Tool (A) can be fully seated, the fuel injection pump timing is correct. No resistance should be felt when the timing pin is inserted into hole (8) of the fuel injection pump body.Note: Some fuel injection pumps are installed with tamper proof bolts. Tool (B) may be necessary in order to remove the tamper proof bolts.
Remove four bolts (3) that fasten the fuel injection pump gear to the fuel injection pump. Timing gear (9) should be free from the fuel injection pump shaft.
Illustration 3 g00808376
Typical example
Remove three flange nuts (10) and fuel injection pump (11) from the engine.
Illustration 4 g00808386
Typical example
Remove O-ring seal (12) from fuel injection pump (11) .
Parts sound JOHNSON:
0341491
0341491 SOUND BLANKET, Port
BJ200CXEDR, BJ200CXEEB, BJ225CXEEC, J200CXECM, J200CXEOC, J200CXEUA, J225CXECS, J225CXEDE, J225CXEOB, J225CXEUD, J225HPLEEN, J250CXECD, J250CXEEN, SJ200WTPLA, SJ200WTPLS
0341493
0341493 SOUND BLANKET, Front
BJ200CXEDR, BJ200CXEEB, BJ200CXSSE, BJ225CXEEC, BJ225CXSSR, J200CXECM, J200CXEOC, J200CXEUA, J225CXECS, J225CXEDE, J225CXEOB, J225CXEUD, J225HPLEEN, J225HPLSSC, J250CXECD, J250CXEEN, J250CXSSS, SJ200WTPLA, SJ200WTPLS
0341494
0341494 SOUND BLANKET, Top
BJ200CXEDR, BJ200CXEEB, BJ200CXSSE, BJ225CXEEC, BJ225CXSSR, J200CXECM, J200CXEOC, J200CXEUA, J225CXECS, J225CXEDE, J225CXEOB, J225CXEUD, J225HPLEEN, J225HPLSSC, J250CXECD, J250CXEEN, J250CXSSS, SJ200WTPLA, SJ200WTPLS
0341492
0341492 SOUND BLANKET, Stbd.
BJ200CXEDR, BJ200CXEEB, BJ225CXEEC, J200CXECM, J200CXEOC, J200CXEUA, J225CXECS, J225CXEDE, J225CXEOB, J225CXEUD, J225HPLEEN, J250CXECD, J250CXEEN, SJ200WTPLA, SJ200WTPLS
0345774
0345774 SOUND BLANKET, Stbd.
BJ200CXEEB, BJ200CXSSE, BJ225CXEEC, BJ225CXSSR, J225HPLEEN, J225HPLSSC, J250CXEEN, J250CXSSS