0348220 *SOUND BLANKET, Stbd. JOHNSON
BJ175PLSIF, J150CXSDE, J150CXSNF, J150CXSOB, J150CXSRM, J150CXSTA, J150GLSDE, J150GLSOB, J150GLSRM, J150GLSTA, J150GLSTF, J150JPLSIF, J150MLSOR, J150MLSRC, J150MLSTS, J150PLSDD, J150PLSOE, J150PLSRB, J150PLSTF, J150PXSDD, J150PXSOE, J150PXSRB, J150WP
SOUND
Price: query
Rating:
Compatible models:
BJ175PLSIF
J150CXSDE
J150CXSNF
J150CXSOB
J150CXSRM
J150CXSTA
J150GLSDE
J150GLSOB
J150GLSRM
J150GLSTA
J150GLSTF
J150JPLSIF
J150MLSOR
J150MLSRC
J150MLSTS
J150PLSDD
J150PLSOE
J150PLSRB
J150PLSTF
J150PXSDD
J150PXSOE
J150PXSRB
J150WPLSIF
J175CXSDE
J175CXSNF
J175CXSOB
J175CXSRM
J175CXSTA
J175GLSDE
J175GLSOB
J175GLSRM
J175GLSTA
J175GLSTF
J175MXSOR
J175MXSRC
J175MXSTS
J175PLSDD
J175PLSOE
J175PLSRB
J175PLSTF
J175PXSDD
J175PXSOE
J175PXSRB
JOHNSON
BRP JOHNSON entire parts catalog list:
- ENGINE COVER » 0348220
J150CXSNF, J150PLSNF, J150PXSNF, J150VLSNF 2002
J150CXSOB 2004,2005
J150CXSRM 2004
J150CXSTA 2003
J150GLSDE 2006
J150GLSOB 2004,2005
J150GLSRM 2004
J150GLSTA, J150PLSTM, J150PXSTM 2003
J150GLSTF 2003
J150JPLSIF, J150PLSIF, J150VCXSIF, J150VLSIF, J150VXSIF, RJ150PLSIF, RJ150VCSIF, RJ150VLSIF, RJ150VXSIF 2001
J150MLSOR, J150MXSOR 2004,2005
J150MLSRC, J150MXSRC 2004
J150MLSTS, J150MXSTS 2003
J150PLSDD 2006
J150PLSOE 2004,2005
J150PLSRB 2004
J150PLSTF 2003
J150PXSDD 2006
J150PXSOE 2004,2005
J150PXSRB 2004
J150WPLSIF 2001
J175CXSDE 2006
J175CXSNF, J175PLSNF, J175PXSNF, J175VLSNF 2002
J175CXSOB 2004,2005
J175CXSRM 2004
J175CXSTA 2003
J175GLSDE 2006
J175GLSOB 2004,2005
J175GLSRM 2004
J175GLSTA, J175PLSTM, J175PXSTM 2003
J175GLSTF 2003
J175MXSOR 2004,2005
J175MXSRC 2004
J175MXSTS 2003
J175PLSDD 2006
J175PLSOE 2004,2005
J175PLSRB 2004
J175PLSTF 2003
J175PXSDD 2006
J175PXSOE 2004,2005
J175PXSRB 2004
Information:
Illustration 1 g01287642
Schematic for the electrical power supply circuitTest Step 1. Inspect the Electrical Connectors and the Wiring
Turn the battery disconnect switch to the OFF position.
Remove electrical power from the ECM.
Illustration 2 g01186024
Location of the J1/P1 ECM connectors (typical left side engine view)
Thoroughly inspect theJ1/P1 ECM connectors. Also, thoroughly inspect the machine connector. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 3 g01287651
Terminal locations at the P1 ECM connector (P1-48) +Battery (P1-52) +Battery (P1-53) +Battery (P1-61) −Battery (P1-63) −Battery (P1-65) −Battery (P1-70) Keyswitch
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors that are associated with the circuit.
Check the allen head screw for each of the ECM connectors and the machine connectors for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasion and for pinch points from the sensors back to the ECM.Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points. All connections and grounds are tight and free of corrosion.Results:
OK - The harness and connectors appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Battery Voltage at the ECM
Disconnect the J1/P1 ECM connector.
Turn the battery disconnect switch to the ON position.
Restore electrical power to the ECM.
Measure the voltage between terminals P1-48 (unswitched +Battery) and P1-61 (−Battery).
Measure the voltage between P1-52 (unswitched +Battery) and P1-63 (−Battery).
Measure the voltage between P1-53 (unswitched +Battery) and P1-65 (−Battery) (if applicable).
Measure the voltage between P1-70 (keyswitch) and P1-63 (−Battery).
Remove the electrical power from the ECM.Expected Result:The measured voltage is between 22.0 VDC and 27.0 VDC.Results:
OK - The ECM is receiving the correct voltage at this time.Repair: There may be an intermittent electrical problem in the circuit. If an intermittent problem is suspected, refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - The voltage is not correct at the ECM. There is a problem in the circuit for the battery power. There may be a problem with the batteries. Proceed to Test Step 3.
Keyswitch voltage out of range - There is a problem in the circuit for the keyswitch. Proceed to Test Step 4.Test Step 3. Check the Batteries
Measure the no-load battery voltage at the battery posts.
Load test the batteries. Use the 4C-4911 Battery Load Tester. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 and 12 Volt Lead Acid Batteries" and Special Instruction, SEHS7633, "Battery Test Procedure".Expected Result:The batteries pass the load test. The measured voltage is the minimum specification for a 12V or 24V system.Results:
OK - The batteries are OK.Repair: There is an open circuit or excessive resistance in the wiring or connections between the batteries and the ECM. Verify that the circuit protection is OK. Check the connections at the machine connector. Verify that the connection for the engine ground is clean and tight and that the battery disconnect switch is functioning properly. Repair the connectors or wiring and/or replace the connectors or wiring. Verify that the repair eliminates the problem.STOP
Not OK - The battery voltage is low or the battery did not pass the load test.Repair: Recharge or replace the faulty batteries. Verify that the repair eliminates the problem.STOPTest Step 4. Check the Voltage from the Keyswitch to the ECM
Remove the wire from the terminal R of the keyswitch.
Restore electrical power to the ECM.
Measure the voltage on terminal B of the keyswitch to engine ground.
Measure the voltage on terminal R of the keyswitch to engine ground.
Remove electrical power from the ECM.Expected Result:Voltage is present on terminal B and terminal R at the keyswitch.Results:
OK - Voltage is present on terminal B and terminal R at the keyswitch.Repair: The problem is in the wiring harness between the keyswitch and the ECM connector. Repair the circuit. Replace parts, if necessary. Verify that the problem is eliminated.STOP
Not OK - Voltage is not present on terminal B at the keyswitch.Repair: If voltage is not present on terminal B, repair the wire between the +Battery and the keyswitch. Verify that the circuit protection for the keyswitch is OK. Verify that the problem is eliminated.STOP
Not OK - Voltage is not present on terminal R at the keyswitch.Repair: If voltage is present on terminal B of the keyswitch but not present on terminal R, there is a problem with the keyswitch. Replace the keyswitch. Return all wiring to the original configuration. Verify that the problem is eliminated.STOP
Parts sound JOHNSON:
0348219
0348219 *SOUND BLANKET, Port
BJ175PLSIF, J150CXSDE, J150CXSNF, J150CXSOB, J150CXSRM, J150CXSTA, J150GLSDE, J150GLSOB, J150GLSRM, J150GLSTA, J150GLSTF, J150JPLSIF, J150MLSOR, J150MLSRC, J150MLSTS, J150PLSDD, J150PLSOE, J150PLSRB, J150PLSTF, J150PXSDD, J150PXSOE, J150PXSRB, J150WP