0115349 ROLL PIN, Clamp screw JOHNSON
BJ2REDE, BJ2REUD, BJ3ROEDE, BJ3ROEUD, HJ2DRETC, HJ3REIC, HJ3RENR, HJ3RETC, J2RECS, J2REEC, J2ROEOB, J2RTSSR, J2WREES, J2WRSSC, J3REEC, J3ROECS, J3ROEOB, J3RTLSSR, J3WREES, J3WRSSC
ROLL
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- STERN BRACKET & SWIVEL BRACKET » 0115349
BJ3ROEDE, HJ3ROEDE, HJ3RSA, J3ROEDE, SJ3ROEDE 1996
BJ3ROEUD, HJ3ROEUD, HJ3RSK, J3ROEUD, SJ3ROEUD 1997
HJ2DRERM, HJ2DRETC 1993,1994
HJ3REIC 1991
HJ3RENR 1992
HJ3RERM, HJ3RETC 1993,1994
J2RECS, J2RSS 1998
J2REEC 1999
J2ROEOB 1995
J2RTSSR 2000
J2WREES 1999
J2WRSSC 2000
J3REEC, J3RLEEC 1999
J3ROECS, J3ROLECS, J3RSS 1998
J3ROEOB 1995
J3RTLSSR, J3RTSSR 2000
J3WREES 1999
J3WRSSC 2000
Information:
start by: a) remove fuel injection pump housing and governor 1. Put the fuel injection pump housing and governor in position on tool (A). 2. Remove bolts (1) that hold the governor housing (2) to the fuel injection pump housing.3. Remove governor housing (2).4. Remove two bolts (3) from the cover. Remove cover (4) from over the torque spring. 5. Remove spring (7), wave washer (6) and guide (5) from the governor housing.6. Remove gasket (8) from the governor housing. 7. Remove bolt (11) and nut (9) from the torque spring (10). Remove the torque spring.8. Remove pin (12) from the hole in the fuel injection pump housing. 9. Remove seat (15) and over fueling spring (16) from the shaft.10. Pull shaft (13) up and remove lever (14). 11. Remove riser (follower) (18) from the shaft.12. Remove ring and lever (17) from the dowel. 13. Remove cover (19) with tool (B). Tool (B) can cause damage to cover. Always inspect the cover for damage and install a new cover if needed. 14. Install timing pin (20) to hold the camshaft from turning.15. Remove three bolts (21) that hold the flyweight assembly in position.16. Remove flyweight assembly (22).17. Remove the timing pin from the fuel injection pump housing.Connection Of Governor To Fuel Injection Pump Housing
1. Put the fuel injection pump housing on tool (A).2. Install timing pin (1) to hold the camshaft from turning.3. Put flyweight assembly (2) in position on the camshaft.
Make sure the pin that holds the shaft in the flyweight assembly is in position before installing the flyweight assembly.
4. Install three new bolts that hold the flyweight assembly to the camshaft. The bolts for holding the flyweight assembly to the camshaft have a locking material on the threads. The bolts must not be used more then one time. 5. Install cover (3) over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (4). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover.
7. Put lever (7) on the dowel. Install ring (6).8. Install pin (5) in the fuel injection pump housing with the round edge down. 9. Put the riser (follower) (11) in position between the flyweights. Lift the flyweights up with a piece of wire and push the riser (follower) forward.10. Put lever (10) in position in the groove of the riser (follower) (11) and the ball end engaged in the sleeve shaft lever (8). Install shaft (9) that holds the lever in position.
If lever (10) is not installed correctly, the governor cannot operate and can cause the engine to over speed.
11. Install over fueling spring (14) and seat (13) on the shaft.12. Install the torque spring (12). Install the bolt and nut that hold the torque spring in position. 13. Install guide (18), wave washer (16) and spring (17) in the governor housing.14. Put a new gasket (15) on the governor housing. 15. Install cover (19) over the torque spring. Install the two bolts that hold the cover in position.16. Put the governor housing on the fuel injection pump housing. Install the bolts that hold the governor housing in position.end by: a) install fuel injection pump housing and governor
1. Put the fuel injection pump housing on tool (A).2. Install timing pin (1) to hold the camshaft from turning.3. Put flyweight assembly (2) in position on the camshaft.
Make sure the pin that holds the shaft in the flyweight assembly is in position before installing the flyweight assembly.
4. Install three new bolts that hold the flyweight assembly to the camshaft. The bolts for holding the flyweight assembly to the camshaft have a locking material on the threads. The bolts must not be used more then one time. 5. Install cover (3) over the flyweight assembly with tool (B). 6. Grind a taper on the bottom edge of a 1/8" screwdriver (4). Install the screwdriver through the bolt hole in the governor housing. The screwdriver must fit evenly against the flyweight assembly cover. Make a mark (stake) in four places around the cover in line with the groove in the camshaft.
Never install a used flyweight cover.
7. Put lever (7) on the dowel. Install ring (6).8. Install pin (5) in the fuel injection pump housing with the round edge down. 9. Put the riser (follower) (11) in position between the flyweights. Lift the flyweights up with a piece of wire and push the riser (follower) forward.10. Put lever (10) in position in the groove of the riser (follower) (11) and the ball end engaged in the sleeve shaft lever (8). Install shaft (9) that holds the lever in position.
If lever (10) is not installed correctly, the governor cannot operate and can cause the engine to over speed.
11. Install over fueling spring (14) and seat (13) on the shaft.12. Install the torque spring (12). Install the bolt and nut that hold the torque spring in position. 13. Install guide (18), wave washer (16) and spring (17) in the governor housing.14. Put a new gasket (15) on the governor housing. 15. Install cover (19) over the torque spring. Install the two bolts that hold the cover in position.16. Put the governor housing on the fuel injection pump housing. Install the bolts that hold the governor housing in position.end by: a) install fuel injection pump housing and governor