0311348 SPRING,Choke JOHNSON
6R69M, 6R70B, 6R71E, 6R72D, 6R73S, 6R74C, 6R75R, 6R76A, 6R77M, 6R78B, 6R79E, CD-25A, LD-13B
SPRING
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- CARBURETOR AND STARTER GROUP » 0311348
6R71E, 6R71G, 6RL71E, 6RL71G 1971
6R72D, 6RL72 1972
6R73S, 6RL73S 1973
6R74C, 6RL74C 1974
6R75R, 6RL75R 1975
6R76A, 6RL76A 1976
6R77M, 6RL77M 1977
6R78B, 6RL78B 1978
6R79E, 6RL79E 1979
CD-25A, CD-25C, CD-25R, CDL-25A, CDL-25C, CDL-25R 1968
LD-13B, LD-13E, LD-13M, LDL-13B, LDL-13E, LDL-13M 1968
Information:
1. Locate top center (TC) compressing stroke for No. 1 piston. See LOCATING TOP CENTER COMPRESSION POSITION FOR NO. 1 PISTON in TESTING AND ADJUSTING. 2. Install the timing fixture plate (A), on the rear face of the accessory drive shaft housing.3. If the plate can be installed with the dowels in the accessory drive shaft housing aligned with the dowel holes in the plate, the accessory drive shaft is correctly timed. Proceed to Step 8. If the plate cannot be installed, continue with Step 4. 4. Remove the cover (1) from the front of the timing gear cover. Remove the accessory drive gear retaining nut and washer. 5. Using tool (B), separate the gear from the accessory drive shaft. Rotate the accessory drive shaft until the timing fixture plate (A) can be installed.6. Install the conical washer on the drive shaft with the O.D. in contact with the gear. Install and tighten the retaining nut to 100 10 lb. ft. (13,8 1,4 mkg). 7. Install the cover (1) on the timing gear cover, and remove the timing fixture plate.8. Position the fuel injection pump housing and governor on the engine, and install the mounting bolts.9. Connect the fuel injection lines and tighten the retaining nut to 30 5 lb. ft. (4,1 0,7 mkg).10. Connect the fuel ratio control sensing line.11. Connect the turbocharger oil supply line and clamp.12. Connect the governor control linkage.
When the governor control linkage is connected the spring tension must hold the governor control lever towards the OFF position.
Separate Governor From Fuel Injection Pump Housing
preparatory steps: a) remove fuel injection pump housing and governor as a unitb) remove fuel ratio control1. Remove idle screw housing plate assembly, and shut down solenoid. 2. Remove two retaining bolts (3) and remove the solenoid fuel shutoff lever (4).3. Remove the idle screw cover (1).4. Remove idle screw housing (2).5. Remove the rack stop collar retaining screw (7). 6. Remove the rack stop collar (5), collar (8), and spring (6).7. Remove the governor-to-fuel injection pump housing mounting bolts (9). 8. Remove the governor housing (10).9. Remove the governor spring (13), seat assembly (11), and washer-type spring. 10. Remove the three mounting bolts (12) and lock that secure the cylinder and weight assemblies (14) to the fuel injection pump housing.11. Pull the cylinder and weight assemblies straight out to clear locating dowels.12. Move the cylinder and weight assemblies sideways to disengage slot in piston from the rack (15).Connect Governor To Fuel Injection Pump Housing
1. Position the cylinder and weight assemblies (1) on the fuel injection pump housing so slot in piston is engaged with the rack (2).2. Push the cylinder and weight assemblies onto the locating dowels. 3. Install the three mounting bolts (5) and lock.4. Install the washer-type spring, seat assembly (4), and governor spring (6) on the cylinder assembly. The washer-type spring should be installed so the outside diameter of spring will contact the guide in governor housing (3).5. Position the governor housing (3) on the fuel injection pump housing, and install the governor mounting bolts. 6. Install the spring (8), collar (10), and rack stop collar (7).7. Install the rack stop collar retaining screw (9). 8. Position the idle screw housing (11) on the governor.9. Install the solenoid fuel shutoff lever (12). Install the lever retaining bolts and lock.10. Install the idle screw housing plate assembly, so the dowel in the housing engages slot (13) in rack stop collar.11. Install the shut down solenoid.12. Install the idle screw cover.concluding steps: a) install fuel injection pump housing and governor as a unitb) install fuel ratio controlc) set the rack and adjust governor (See FUEL RACK SETTING AND GOVERNOR ADJUSTMENTS in TESTING AND ADJUSTING)
When the governor control linkage is connected the spring tension must hold the governor control lever towards the OFF position.
Separate Governor From Fuel Injection Pump Housing
preparatory steps: a) remove fuel injection pump housing and governor as a unitb) remove fuel ratio control1. Remove idle screw housing plate assembly, and shut down solenoid. 2. Remove two retaining bolts (3) and remove the solenoid fuel shutoff lever (4).3. Remove the idle screw cover (1).4. Remove idle screw housing (2).5. Remove the rack stop collar retaining screw (7). 6. Remove the rack stop collar (5), collar (8), and spring (6).7. Remove the governor-to-fuel injection pump housing mounting bolts (9). 8. Remove the governor housing (10).9. Remove the governor spring (13), seat assembly (11), and washer-type spring. 10. Remove the three mounting bolts (12) and lock that secure the cylinder and weight assemblies (14) to the fuel injection pump housing.11. Pull the cylinder and weight assemblies straight out to clear locating dowels.12. Move the cylinder and weight assemblies sideways to disengage slot in piston from the rack (15).Connect Governor To Fuel Injection Pump Housing
1. Position the cylinder and weight assemblies (1) on the fuel injection pump housing so slot in piston is engaged with the rack (2).2. Push the cylinder and weight assemblies onto the locating dowels. 3. Install the three mounting bolts (5) and lock.4. Install the washer-type spring, seat assembly (4), and governor spring (6) on the cylinder assembly. The washer-type spring should be installed so the outside diameter of spring will contact the guide in governor housing (3).5. Position the governor housing (3) on the fuel injection pump housing, and install the governor mounting bolts. 6. Install the spring (8), collar (10), and rack stop collar (7).7. Install the rack stop collar retaining screw (9). 8. Position the idle screw housing (11) on the governor.9. Install the solenoid fuel shutoff lever (12). Install the lever retaining bolts and lock.10. Install the idle screw housing plate assembly, so the dowel in the housing engages slot (13) in rack stop collar.11. Install the shut down solenoid.12. Install the idle screw cover.concluding steps: a) install fuel injection pump housing and governor as a unitb) install fuel ratio controlc) set the rack and adjust governor (See FUEL RACK SETTING AND GOVERNOR ADJUSTMENTS in TESTING AND ADJUSTING)
Parts spring JOHNSON:
0312853
0312853 SPRING,Throttle return
10E74G, 15E74G, 1R69C, 1R70R, 2R71A, 2R72M, 2R73B, 2R74E, 2R75D, 2R76S, 2R77C, 2R78R, 4R69B, 4R70E, 4R71D, 4R72S, 4R73C, 4R74R, 4R75A, 4R76M, 4R77B, 4R78E, 6R69M, 6R70B, 6R71E, 6R72D, 6R73S, 6R74C, 6R75R, 6R76A, 6R77M, CD-25A, JH-23A, LD-13B
0301829
0301829 SPRING,Lock
100ESL71A, 115ESL69E, 115ESL70D, 125ESL71C, 20R69B, 20R70C, 20R71S, 25R69B, 25R70C, 25R71S, 33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40E70A, 40E71B, 40ES69R, 40ES70A, 40R69R, 40R70A, 4R69B, 4R70E, 4R71D, 50ES71S, 55ES69A, 60ES70B, 6R69M, 6R70B, 6R71E,
0303594
0309736
0309736 SPRING
6R69M, 6R70B, 6R71E, 6R72D, 6R73S, 6R74C, 6R75R, 6R76A, 6R77M, 6R78B, 6R79E, 9R69S, 9R70A, 9R72M, 9R73B, CD-25A, J5RCIC, J5RCSS, J5RHCNR, J5RHCTA, J6RCCS, J6RCDE, J6RCEC, J6RCOB, J6RCRM, J6RCUD, J6RESR, J8RCCS, J8RCDE, J8RCEC, J8RCIC, J8RCNR, J8RCOB,
0303466
0303466 SPRING, Detent
6R69M, 6R70B, 6R71E, 6R72D, 6R73S, 6R74C, 6R75R, 6R76A, 6R77M, 6R78B, 6R79E, 9R69S, 9R70A, 9R71R, 9R72M, 9R73B, CD-25A, MQ-14D, VJ14RCCS, VJ14RCCS, VJ14RCEC, VJ14RCEC
0303236
0303236 SPRING, Shift lever and shaft to washer
6R69M, 6R70B, 6R71E, 6R72D, 6R74C, 6R75R, 6R76A, 6R77M, 6R78B, 6R79E, CD-25A, VJ14RCCS, VJ14RCCS, VJ14RCEC, VJ14RCEC
0304283
0304283 SPRING, Tilting lever
6R69M, 6R70B, 6R71E, 6R72D, 6R73S, 6R74C, 6R75R, 6R76A, 6R77M, 6R78B, 6R79E, CD-25A
0304282
0304282 SPRING, Reverse lock
6R69M, 6R70B, 6R71E, 6R72D, 6R73S, 6R74C, 6R75R, 6R76A, 6R77M, 6R78B, 6R79E, CD-25A