0441230 SPRING, Detent JOHNSON
BJ5FRBECC, BJ5FRBEUS, HJ6FRECA, HJ6FREUR, J6R4SRC, J6R4STS
SPRING
Price: query
Rating:
BRP JOHNSON entire parts catalog list:
- STEERING HANDLE » 0441230
HJ6FRECA, HJ6FRLECA 1998
HJ6FREUR, HJ6FRLEUR 1997
J6R4SRC, J6RL4SRC 2004
J6R4STS, J6RL4STS 2003
Information:
Illustration 1 g00667579
Test Step 1. Check for Connector Damage.
Turn the circuit breaker for the engine to the OFF position.
Turn the keyswitch to the OFF position.
Thoroughly inspect the connectors J1/P1 and J2/P2 for the Electronic Control Module (ECM). Inspect all of the other connectors. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the customer connector (allen head screw) for the proper torque of 2.25 0.25 N m (20 2 lb in).
Check the harness and the wiring for abrasion and pinch points.Expected Result:The connectors and wiring should be free of the following problems: damage, corrosion, abrasion and incorrect attachment.Results:
OK - The connectors and wiring are okay. Proceed to test step 2.
Not OK - The connectors and/or wiring need repair.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Stop.Test Step 2. Inspect the Throttle Assembly.Inspect the throttle assembly for damaged components.Expected Result:The throttle assembly should operate smoothly without excessive drag. The throttle assembly should return to the low idle position without assistance in less than one second.Results:
OK - The throttle assembly is operating correctly. Proceed to test step 3.
Not OK - The throttle assembly is not operating correctly.Repair: Repair the throttle assembly or replace the throttle assembly. The throttle assembly should operate smoothly without excessive drag. The throttle assembly should return to the low idle position without assistance in less than one second. Stop.Test Step 3. Check the Throttle Position with the Caterpillar Electronic Technician (ET).
Connect the Cat ET to the cab service tool connector J42. Start the Cat ET.
Turn the circuit breaker for the engine to the ON position.
Turn the keyswitch to the ON position. The engine should be off.
Observe the throttle position reading on the Cat ET.
Depress the throttle and release the throttle.Expected Result:The throttle position should read 0 percent when the throttle pedal is released. The throttle position should increase to 100 percent when the throttle pedal is fully depressed.Results:
OK - The throttle position reads 0 percent when the throttle pedal is released. The throttle position increases to 100 percent when the throttle pedal is fully depressed. The throttle position sensor is okay.Repair: There may be an intermittent problem. If the problem is intermittent, perform the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors". Stop.
Not OK - The throttle position does not read 0 percent when the throttle pedal is released. The throttle position does not increase to 100 percent when the throttle pedal is fully depressed. The ECM is not receiving a correct signal from the sensor. There may be a problem in the harness. Proceed to test step 4.Test Step 4. Check the Sensor Supply Voltage at the Throttle Position Sensor Connector.
Turn the keyswitch to the OFF position. The engine should be off.
Disconnect the connector for the throttle position sensor J35/P35.Note: If you remove the sensor common from a sensor, an open circuit diagnostic code will be generated for that sensor. Troubleshoot the original code. Delete the logged diagnostic code when you are finished.
Turn the keyswitch to the ON position. The engine should be off.
Measure the sensor supply voltage at the connector between P35-A and P35-B.Expected Result:The voltage should be 8.0 0.4 VDC.Results:
OK - The voltage is 8.0 0.4 VDC. The supply voltage is reaching the sensor. Proceed to test step 5.
Not OK - The voltage is not 8.0 0.4 VDC. The supply voltage is not reaching the sensor. Proceed to test step 8.Test Step 5. Check the Signal Frequency and the Duty Cycle at the Throttle Position Sensor Connector.
Turn the keyswitch to the OFF position. The engine should be off.
Remove wire F702-GN from P35-C at the sensor connector.
Turn the keyswitch to the ON position. The engine should be off.
Measure the frequency and the duty cycle between wire F702-GN and P35-B.Note: Set the multimeter to "VDC". Press the "Hz" button twice so that the % symbol is displayed.
Depress the throttle and
Parts spring JOHNSON:
0325338
0325338 SPRING, Plunger
BJ10FAEDC, BJ10FAEUR, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ5DREDS, BJ5DREUC, BJ5FRBECC, BJ5FRBEUS, BJ6DRECR, BJ6DREDS, BJ6DREUC, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, BJ8RCLT, BJ8R
0332576
0332576 SPRING, Idle adjustment
BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ115ELEDR, BJ115ELEUA, BJ115GLECM, BJ115PLEEM, BJ115PLSIE, BJ115PLSSB, BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, BJ135PLSIF, BJ150ELECD, BJ150ELEDB, BJ150ELEUC, BJ15FAEDR, B
0331970
0331970 SPRING, Friction
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15RELEUC, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25PL3EEM, BJ25PL3SIE, BJ25PL3SSB, BJ35ARECR, BJ35AREDS, BJ35AREEA, BJ35AREUC, BJ35E3SIE, BJ35E3SSB, B
0336179
0336179 SPRING
AM55RSLD, BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ130PLEED, BJ130PLSSS, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, BJ135PLSIF, BJ15EEDS, BJ15RELEUC, BJ250CXECB, BJ250CXEDA, BJ250CXEUM, BJ25ARECA, BJ25ARE
0336681
0336681 SPRING, Starter
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ15RELEUC, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25PL3EEM, BJ25PL3SIE, BJ25PL3SS
0336842
0336842 SPRING CLIP, Float valve
AM55RSLD, BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ115ELEDR, BJ115ELEUA, BJ115GLECM, BJ115PLEEM, BJ115PLSIE, BJ115PLSSB, BJ115TLEDA, BJ130PLEED, BJ130PLSSS, BJ13
0342030
0342030 SPRING, Idle mixture
BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ5FRBECC, BJ5FRBEUS, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, HJ6FRECA, HJ6FREUR, J10FEXEO, J15DLEOC
0342763
0342763 SPRING, Diaphragm return
BJ10FDLECM, BJ15FDLECM, BJ5FRBECC, BJ5FRBEUS, HJ6FRECA, HJ6FREUR, J6R4SRC, J6R4STS