5031285 SPRING JOHNSON
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
SPRING
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- GEARS » 5031285
BJ40PL4SRS, J40PL4SRM 2004
BJ50PL4SDR, J50PL4SDE 2006
BJ50PL4SOC, J50PL4SOB 2005
BJ50PL4SRS, J50PL4SRM 2004
J40PL4SNF 2002
J40PL4STC 2003
J50PL4SNF 2002
J50PL4STC 2003
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B 8T-3052 Degree Wheel 1 Start By:
Remove the engine oil pump.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00998459
Use Tooling (A) to rotate the crankshaft until the connecting rod is at the bottom center.
Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary. Note: Do not stamp the connecting rod assembly. Stamping or punching the connecting rod assembly could cause the connecting rod to fracture.
Remove bolts (1) and connecting rod bearing cap (2) from the connecting rod.
Remove the lower half of the connecting rod bearing from the connecting rod bearing cap.
Push the connecting rod away from the crankshaft. Remove the upper half of the connecting rod bearing from the connecting rod. Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Illustration 2 g00998730
Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.
Install a new lower half connecting rod bearing (3) in connecting rod bearing cap (2). Note: Ensure that bearing locking tab (4) is located in the notch of the connecting rod bearing cap.
Install a new upper half connecting rod bearing in the connecting rod. Note: Ensure that the bearing locking tab is located in the notch of the connecting rod.
Pull the connecting rod onto the crankshaft.
Illustration 3 g01016640
Position connecting rod bearing cap (2) on the connecting rod. Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side of the piston cooling jet.
Lubricate the threads of bolts (1) with clean engine oil. Install the bolts.
Tighten bolts (1), as follows:
Tighten Bolt (A) and Bolt (C) to a torque of 70 4 N m (52 3 lb ft).
Tighten Bolt (B) and Bolt (D) to a torque of 70 4 N m (52 3 lb ft).
Turn Bolt (B) and Bolt (D) for an additional 60 5 degrees (1/6 turn). Note: If Tooling (B) is not used, place an index mark on each bolt.
Tighten Bolt (A) and Bolt (C) again to a torque of 70 4 N m (52 3 lb ft).
Tighten Bolt (A) and Bolt (C) for an additional 60 5 degrees (1/6 turn). Note: If Tooling (B) is not used, place an index mark on each bolt.
Rotate the crankshaft in order to ensure that the crankshaft turns freely. End By:
Install the engine oil pump.
Parts spring JOHNSON:
5031087
5031087 SPRING
BJ40PL4SRS, BJ50PL4SRS, BJ60PL4STC, BJ70PL4STC, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC, J60PL4SNF, J70FLTLECS, J70PL4SNF
5031284
5031284 SPRING
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J10EL4SRC, J10R4SNF, J10R4SR, J10R4STC, J15R4SNF, J15R4SR, J15R4STC, J15RL4SR, J25PL4SOC, J25PL4SRS, J30PL4SDR
5031383
5031282
5031282 SPRING
BJ115L4SDA, BJ140CX4DR, BJ140L4SDR, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, BJ90PL4SDA, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031492
5031492 SPRING, TILT LOCK
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031283
5031283 SPRING, RETURN
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031286
5031286 SPRING, DOG
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5034167
5034167 *SPRING
BJ40PL4SRS, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, J40PL4STC, J50PL4STC