0341565 JOHNSON STERN BRACKET, Port


0341565 STERN BRACKET, Port JOHNSON BJ10EEDD, BJ10FAEDC, BJ10FDLEDR, BJ10FDLEUA, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ8FRBEDC, HJ15KCLN, J10EEOE, J10FEXEO, J15DLEOC, J15EEOD, SJ10REDD, SJ10RPB STERN
0341565 STERN BRACKET, Port JOHNSON
Rating:
63

Buy STERN BRACKET, Port 0341565 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$89.99
 

13-09-2017
4.00[1.80] pounds
OMC: OMC
0328268 Stern Bracket Port Side Evinrude Johnson 4 Stroke OMC Outboard 328268 0341565
OMC||0328268, 328268||Used & Guaranteed Good Condition!||1990-2007||9.9, 10, 15hp
Number on catalog scheme: 45
 

BRP JOHNSON entire parts catalog list:

BJ10EEDD, BJ10ELEDD, BJ10REDD, BJ10RELEDD, BJ10RLEDD, BJ10SELEDD, J10EEDD, J10ELEDD, J10REDD, J10RELEDD, J10RLEDD, J10SELEDD 1996
BJ10FAEDC, BJ10FCLEDC, BJ10FWEDC, BJ10FWLEDC, HJ10FDEDC, HJ10FDLEDC, HJ10FELEDC, HJ10FTEDC, HJ10FTLEDC 1996
BJ10FDLEDR, BJ10FPXEDC, BJ10FRELDR, J10FEXEDR, J10FREDR, J10FRELEDR, J10FRLEDR 1996
BJ10FDLEUA, BJ10FPXEUR, BJ10FRELUA, J10FEXEUA, J10FRELEUA, J10FREUA, J10FRLEUA 1997
BJ15EEDS, BJ15ELEDS, BJ15REDS, BJ15RLEDS, J15EEDS, J15ELEDS, J15REDS, J15RELEDS, J15RLEDS, SJ15BAEDC, SJ15REDS, SJ15RLEDS 1996
BJ15FAEDR, BJ15FDLEDR, BJ15FKEDR, BJ15FREDR, BJ15FRELEDR, BJ15FWEDC, BJ15FWLEDC, J15FKEDR, J15FREDR, J15FRELEDR, J15FRLEDR 1996
BJ15FAEUA, BJ15FDLEUA, BJ15FKEUA, BJ15FRELUA, BJ15FREUA, BJ15FWEUR, BJ15FWLEUR, J15FKEUA, J15FRELEUA, J15FREUA, J15FRLEUA 1997
BJ8FRBEDC, BJ8FRBLEDC, BJ8FRBXEDC, HJ8FREDC, HJ8FRLEDC, J8FREDC, J8FRXEDC 1996
HJ15KCLN, HJ15KCN, SJ15RPG, SJ15RPLG 1996
J10EEOE, J10ELEOE, J10RELEOE, J10REOE, J10RLEOE, J10SELEOE 1995
J10FEXEO, J10FRELEOC, J10FREOC, J10FRLEO 1995
J15DLEOC, J15FREOC, J15FRLEOC, J15KEOC 1995
J15EEOD, J15ELEOD, J15RELEOD, J15REOD, J15RLEOD 1995
SJ10REDD, SJ10RLEDD, SJ10SELEDD 1996
SJ10RPB, SJ10RPLB 1996

Information:


POSITIONING PIN BEARING (Type A)
POSITIONING PIN BEARING (Type B)
MARKS FOR TIGHTENING CONNECTING ROD BOLTS(1) Bore in connecting rod for piston pin bearing ... 2.1825 .0005 in.(55.436 0.013 mm) Tight fit between connecting rod eye and piston pin bearing ... .002 to .004 in.(0.05 to 0.10 mm) Connecting rod must be heated for installation of piston pin bearing. Do not use a torch.Heat connecting rod to temperature of ... 350 to 500° F(177 to 260° C)Position of pin bearing: Type A (Narrow Taper) - Bearing junction and locating hole are 180° apart (directly across from each other). Bearing junction and locating hole must be assembled within either area "A" (90 10° from centerline through the connecting rod bores) as shown.Type B (Wide Taper) - Bearing junction and locating hole are 155° apart (not directly across from each other). Bearing junction and locating hole must be assembled in the top half of connecting rod eye (12.5 1° above the horizontal centerline) as shown.Make reference to Special Instruction Form No. SMHS7295 for use of pin bearing removal and installation tools and procedures.(2) Bore in connecting rod for bearing with nuts tight to specifications (6) ... 4.0748 .0005 in.(103.500 0.013 mm)(3) Distance between center of bearings ... 10.300 .002 in.(261.62 0.05 mm)(4) Bore in bearing for piston pin (new) ... 2.0012 .0003 in.(50.830 0.008 mm) Diameter of piston pin (new) ... 1.9998 .0002 in.(50.795 0.005 mm)Maximum permissible clearance between bearing and piston pin (worn) ... .003 in.(0.08 mm)(5) Bore in bearing for crankshaft ... 3.8236 to 3.8258 in.(97.119 to 97.175 mm) Clearance between bearing and crankshaft (new) ... .0028 to .0066 in.(0.071 to 0.168 mm)Maximum permissible clearance between bearing and crankshaft (worn) ... .010 in.(0.25 mm) Bearings are available in .025 in. (0.64 mm) and .050 in. (1.27 mm) smaller than original size.(6) Tighten procedure for connecting rod bolts: a. Put engine oil on bolt threads and contact surfaces of nut and cap.b. Tighten both nuts to ... 60 6 lb. ft.(80 8 N m)c. Put a mark on each nut and end of bolt as shown.d. Tighten each nut from mark ... 120 5° The connecting rod must be installed so the chamfer on the edge of bore (5) is near the corner on the crankshaft. The side opposite the chamfered edge must be against the other connecting rod on the same crankshaft pin.Side clearance between two connecting rods on same crankshaft pin (new) ... .011 to .033 in.(0.28 to 0.84 mm)Make reference to Special Instruction Form Nos. GMG02394 & SMHS7366 for information to check and recondition connecting rods.(Straight Pin End)
POSITIONING PIN BEARING
MARKS FOR TIGHTENING CONNECTING ROD BOLTS(1) Bore in connecting rod for piston pin bearing ... 2.1825 .0005 in.(55.436 0.013 mm) Tight fit between connecting rod eye and piston pin bearing ... .002 to .004 in.(0.05 to 0.10 mm) Connecting rod must be heated for installation of piston pin bearing. Do not use a torch.Heat connecting rod to temperature of ... 350 to 500°F(177 to 260°C) Piston pin bearing junction must be assembled within either area "A" (90 10° from the centerline through the n connecting rod bores) as shown.Make reference to Special Instruction Form No. SMHS7295 for use of pin bearing removal and installation tools and procedures.(2) Bore in connecting rod for bearing with nuts tight to specifications (6) ... 4.0748 .0005 in.(103.500 0.013 mm)(3) Distance between center of bearings ... 10.300 .002 in.(261.62 0.05 mm)(4) Bore in bearing for piston pin (new) ... 2.0012 .0003 in.(50.830 0.008 mm) Diameter of piston pin (new) ... 1.9998 .0002 in.(50.795 0.005 mm)Maximum permissible clearance between bearing and piston pin (worn) ... .003 in.(0.08 mm)(5) Bore in bearing for crankshaft ... 3.8236 to 3.8258 in.(97.119 to 97.175 mm) Clearance between bearing and crankshaft (new) ... .0028 to .0066 in.(0.071 to 0.168 mm)Maximum permissible clearance between bearing and crankshaft (worn) ... .010 in.(0.25 mm) Bearings are available in .025 in. (0.64 mm) and .050 in. (1.27 mm) smaller than original size.(6) Tighten procedure for connecting rod bolts: a. Put engine oil on bolt threads and contact surfaces of nut and cap.b. Tighten both nuts to ... 60 6 lb. ft.(80 8 N m)c. Put a mark on each nut and end of bolt as shown.d. Tighten each nut from mark ... 120 5° The connecting rod must be installed so the chamfer on the edge of bore (5) is near the corner on the crankshaft. The side opposite the chamfered edge must be against the other connecting rod on the same crankshaft pin.Side clearance between two connecting rods on same crankshaft pin (new) ... .011 to .033 in.(0.28 to 0.84 mm) Make reference to Special Instruction Form Nos. GMG02394 and SMHS7366 for information to check and recondition connecting rods.


Parts stern JOHNSON:

0341566
 
0341566 STERN BRACKET, Stbd.
BJ10EEDD, BJ10FAEDC, BJ10FDLEDR, BJ10FDLEUA, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ8FRBEDC, HJ15KCLN, J10EEOE, J10FEXEO, J15DLEOC, J15EEOD, SJ10REDD, SJ10RPB
Back to top