0391944 JOHNSON STERN BRKT., Assy., stbd


0391944 STERN BRKT., Assy., stbd JOHNSON J25ECIB, J25ECNE, J25ECTD, J25RSA, J25RSLS STERN
0391944 STERN BRKT., Assy., stbd JOHNSON
Rating:
93

Buy STERN BRKT., Assy., stbd 0391944 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 48
 

Compatible models:

BRP JOHNSON entire parts catalog list:

J25ECIB, J25ECIM, J25ELCIB, J25ELCIM, J25RCIM, J25RLCIM, J25TECIM, J25TELCIM 1981
J25ECNE, J25ELCNE, J25RCNB, J25RELCNB, J25RLCNB, J25TECNB 1982
J25ECTD, J25ELCTD, J25RCTE, J25RLCTE, J25TECTE, J25TELCTE 1983
J25RSA, J25RSLA, J25RWCIM, J25RWLCIM 1981
J25RSLS, J25RSS, J25RWCTE, J25RWLCTE 1983

Information:

Introduction
This publication will provide a procedure to properly flush out the transmission system when the engine oil or hydraulic oil becomes mixed with transmission oil on the machines listed above.Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Safety Section
Do not perform any procedure in this special instruction until you have read this special instruction and you understand this information. Use only proper tools and observe all precautions that pertain to the use of those tools. Failure to follow these procedures can result in personal injury. The following procedures also be observed.Work safely. Most accidents that involve product operation, maintenance, and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills, and tools to perform these functions properly.Safety precautions and warnings are provided in this instruction and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons. Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard.Ensure that all personnel are safe when using a tool, procedure, work method, or operating technique not recommended by Caterpillar. Ensure that the product will not be damaged or the product made unsafe by the operation, lubrication, maintenance, or the repair procedures that are used.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Personal injury or death can result from improperly checking for a leak.Always use a board or cardboard when checking for a leak. Escaping air or fluid under pressure, even a pin-hole size leak, can penetrate body tissue causing serious injury, and possible death.If fluid is injected into your skin, it must be treated immediately by a doctor familiar with this type of injury.
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Failure to follow all safety guidelines prescribed in this document and by governing authorities and regulatory agencies may result in severe injury or death of personnel or machine damage.
When removing a major component or attachment, ensure that it is properly blocked or secured before removing mounting hardware. An assembly that is disconnected without proper blocking may shift or fall, resulting in serious injury or death of personnel or machine damage.
Personal injury or death can result from improper maintenance procedures. To avoid injury or death, follow the procedures exactly as stated below.
Personal injury can result from improper handling of chemicals.Make sure you use all the necessary protective equipment required to do the job.Make sure that you read and understand all directions and hazards described on the labels and material safety data sheet of any chemical that is used.Observe all safety precautions recommended by the chemical manufacturer for handling, storage, and disposal of chemicals.
Climbing equipment may be required to access this service point. Refer to the Operation and Maintenance Manual, "Mounting and Dismounting" topic for safety information.
Before servicing/performing maintenance on the machine, electrical power must be physically disconnected; battery plugs must be disconnected from the batteries, or the trailing cable must be unplugged, and warning tags and padlocks shall be applied by a certified electrician. Certified electricians shall perform or direct any electrical work, including any energized testing, repair work in controllers, motors, or other approved compartments, and shall insure that all compartments are properly closed and inspected prior to re-energization. All applicable lock out and tag out procedures must be followed.


Parts stern JOHNSON:

0391943
 
0391943 STERN BRKT., Assy., stbd
J20CRCCA, J20CRCEM, J20CRCOS, J20CRCUR, J20ECEM, J25ECCM, J25ECDR, J25ECEB, J25ECIB, J25ECNE, J25ECOC, J25ECRS, J25ECTD, J25ECUA, J25RCEM, J28ELCDS, J28ELCDS, J28ESLCCR, J28ESLCCR, J28ESLCEA, J28ESLCEA, J28ESLCUC, J28ESLCUC, J30ECCE, J30ECDM, J30ECED
0391945
 
0391945 STERN BRKT., Assy., port incl items 49,50,51
J25ECIB, J25ECNE, J25ECTD, J25RSA, J25RSLS
0391942
 
0391942 STERN BRKT., Assy., port
J20CRCCA, J20CRCEM, J20CRCOS, J20CRCUR, J20ECEM, J25ECCM, J25ECDR, J25ECEB, J25ECIB, J25ECNE, J25ECOC, J25ECRS, J25ECTD, J25ECUA, J25RCEM, J25TECEM, J28ELCDS, J28ELCDS, J28ESLCCR, J28ESLCCR, J28ESLCEA, J28ESLCEA, J28ESLCUC, J28ESLCUC, J30ECCE, J30ECD
Back to top