5031404 JOHNSON STOP, FUEL INJECTOR


5031404 STOP, FUEL INJECTOR JOHNSON BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC STOP
5031404 STOP, FUEL INJECTOR JOHNSON
Rating:
98

Buy STOP, FUEL INJECTOR 5031404 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

BRP JOHNSON entire parts catalog list:

BJ40PL4SDR, J40PL4SDE 2006
BJ40PL4SOC, J40PL4SOB 2005
BJ40PL4SRS, J40PL4SRM 2004
BJ50PL4SDR, J50PL4SDE 2006
BJ50PL4SOC, J50PL4SOB 2005
BJ50PL4SRS, J50PL4SRM 2004
J40PL4SNF 2002
J40PL4STC 2003
J50PL4SNF 2002
J50PL4STC 2003

Information:


Illustration 1 g01249215
Illustration 2 g01176473
Loosen bolts (2) and (5) in reverse numerical order. Refer to Illustration 2. This will help prevent distortion of the exhaust manifold.
Remove bolts (2) from exhaust manifold (3). Remove bolts (5) and spacers (4) from exhaust manifold (3).
Remove exhaust manifold gaskets (1) from the cylinder head.
If necessary, remove studs (6) from exhaust manifold (3).
Clean all of the components of the exhaust manifold assembly. Check all of the components for wear or for damage. Removal Procedure (Top Mounted Exhaust Manifold)
Start By:
Remove the turbocharger.
Illustration 3 g01249219
Illustration 4 g01176487
Loosen bolts (3) and (6) in reverse numerical order. Refer to Illustration 4. This will help prevent distortion of exhaust manifold (4).
Remove bolts (3) from exhaust manifold (6). Remove bolts (6) and spacers (5) from exhaust manifold (4).
Remove exhaust manifold gaskets (1) from the cylinder head.
If necessary, remove studs (2) from exhaust manifold (4).
Clean all of the components of the exhaust manifold assembly. Check all of the components for wear or for damage. Installation Procedure (Side Mounted Exhaust Manifold)
Table 1
Required Tools
Tool Part Number Part Description Qty
A M10 X - 1.5 by 100 mm
Guide Stud 4 Note: If a bolt for the exhaust manifold has become loose, or a bolt for the exhaust manifold must be loosened, all of the bolts for the exhaust manifold must be loosened. The bolts for the exhaust manifold must be tightened in the correct sequence and to the correct torque.
Illustration 5 g01176473
Illustration 6 g01249215
If necessary, install studs (6) to exhaust manifold (3). Tighten studs (6) to a torque of 18 N m (13 lb ft).
Install Tooling (A) in the cylinder head in Holes (X).
Position exhaust manifold gaskets (1) onto Tooling (A) in the cylinder head.
If the air port in the cylinder head is covered by the gasket, use the following procedure.
Remove exhaust manifold gasket (1) from the cylinder head.
Turn exhaust manifold gasket (1) through 180 degrees.
Reinstall exhaust manifold gasket (1) onto Tooling (A) in the cylinder head.
Position exhaust manifold (3) onto Tooling (A).
Install bolts (2) to exhaust manifold (3). Install spacers (4) and bolts (5) to exhaust manifold (3) in order to secure exhaust manifold (3) to the cylinder head.
Remove Tooling (A). Install remaining spacers (4) and bolts (5) and (2) to exhaust manifold (3).
Tighten bolts (2) and (5) to a torque of 44 N m (32 lb ft). Tighten bolts (2) and (5) in the sequence that is shown in Illustration 5. End By:
Install the turbocharger. Installation Procedure (Top Mounted Exhaust Manifold)
Table 2
Required Tools
Tool Part Number Part Description Qty
A M10 - 1.5 by 100 mm
Guide Stud 4 Note: If a bolt for the exhaust manifold has become loose, or a bolt for the exhaust manifold must be loosened, all of the bolts for the exhaust manifold must be loosened. The bolts for the exhaust manifold must be tightened in the correct sequence and to the correct torque.
Illustration 7 g01176487
Illustration 8 g01249219
If necessary, install studs (2) to exhaust manifold (4). Tighten studs (2) to a torque of 18 N m (13 lb ft).
Install Tooling (A) in the cylinder head in Holes (X).
Position exhaust manifold gaskets (1) onto Tooling (A) in the cylinder head.
If the air port in the cylinder head is covered by the gasket, use the following procedure.
Remove exhaust manifo


Parts stop JOHNSON:

5030886
 
5030886 STOP, Upper thrust
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC, J70FLTLECS
5031551
 
5031551 STOP, PROPELLER BUSHING
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031593
 
5031593 STOP, REMOTE CABLE
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ70PL4SDM, BJ70PL4SOA, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC
Back to top