5033454 JOHNSON STOPPER, THROTTLE CABLE


5033454 STOPPER, THROTTLE CABLE JOHNSON J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR STOPPER

Buy STOPPER, THROTTLE CABLE 5033454 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

BRP JOHNSON entire parts catalog list:

J4R4SDA, J4RL4SDA 2006
J4R4SOR, J4RL4SOR 2005
J4R4SRC, J4RL4SRC 2004
J4R4STS, J4RL4STS 2003
J4R4SUM, J4RL4SUM 2007
J5R4SDA, J5RL4SDA 2006
J5R4SOR, J5RL4SOR 2005
J5R4SRC, J5RL4SRC 2004
J5R4STS, J5RL4STS 2003
J5R4SUM, J5RL4SUM 2007
J6R4SDC, J6RL4SDC 2006
J6R4SOS, J6RL4SOS 2005
J6R4SUR, J6RL4SUR 2007

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01340605
Typical example
If necessary, remove the assembly of dipstick tube. Loosen nut (1) and remove tube assembly (2). remove seal (3) from the tube assembly.Note: Identify the position and orientation of the tube assembly.
Illustration 2 g01340606
Typical example
Place a suitable container below engine oil pan (7). Remove drain plug (5) and drain the engine lubricating oil. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct procedure.
Remove O-ring seal (6) from drain plug (5) .
Disconnect breather hose from the clip that secures the hose to the engine oil pan. Position the breather hose away from the engine oil pan.
Support the assembly of the engine oil pan. Loosen the long isolating screws (8) and the two short isolating screws (9). Mark the position of the clip that secures breather hose. Remove the clip.Note: The isolating screws are held captive by joint (4) .
Remove the assembly of the engine oil pan from the engine.
If necessary, remove the plate for the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     -     Guide Stud
(M8 by 100 mm)     4    
B     6V-6640     Sealant     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
If necessary, install the plate for the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Illustration 3 g01340664
Typical Example
Install Tooling (A) to positions (X) in the cylinder block.
Illustration 4 g01340606
Typical example
Ensure that the engine oil pan (7) is clean and free from damage. Clean the isolating screws (8) and (9). Inspect the isolating screws for deterioration or damage. If necessary, replace the isolating screws. If necessary, ensure that the mating surface of the isolating frame is clean.Note: The isolating screws must be replaced as a complete set in order to ensure the correct clamping of the engine oil pan.
Position a new joint (4) onto the engine oil pan (7) .
Install the isolating screws (8) and (9) to the engine oil pan. Do not install the isolating screws (8) in positions (X). Refer to Illustration 3.Note: The isolating screws are held captive by the joint.
Align the assembly of the engine oil pan with Tooling (A). Install the assembly of the engine oil pan to the isolating frame (12). Install the clip that secures the breather hose in the correct position.
Illustration 5 g01340724
(X) Position of guide studs. (Z) Position of short isolating screws.
Tighten the isolating screws to a torque of 22 N m (16 lb ft). Tighten the isolating screws in the sequence that is shown in Illustration 5.
Remove Tooling (A) .
Illustration 6


Back to top