0379116 JOHNSON STRAP,Front door


0379116 STRAP,Front door JOHNSON 33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40E70A, 40E71B, 40ES69R, 40ES70A, 40R69R, 40R70A, RD-30A, RDS-30A, RK-30A, RX-16M, V4T-14B STRAP
0379116 STRAP,Front door JOHNSON
Rating:
38

Buy STRAP,Front door 0379116 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 26
 

BRP JOHNSON entire parts catalog list:

33E69A, 33EL69A, 33R69A, 33RL69A 1969
33E69A, 33EL69A, 33R69A, 33RL69A 1969
33E70M, 33EL70M, 33R70M, 33RL70M 1970
33E70M, 33EL70M, 33R70M, 33RL70M 1970
40E69R, 40EL69R 1969
40E70A, 40EL70A 1970
40E71B, 40E71G, 40EL71B, 40EL71G, 40R71B, 40R71G, 40RL71B, 40RL71G 1971
40ES69R, 40ESL69R 1969
40ES70A, 40ESL70A 1970
40R69R, 40RL69R 1969
40R70A, 40RL70A 1970
RD-30A, RD-30D, RD-30S, RDL-30A, RDL-30D, RDL-30S 1968
RDS-30A, RDS-30C, RDS-30D, RDS-30S, RDSL-30A, RDSL-30C, RDSL-30D, RDSL-30S 1968
RK-30A, RK-30C, RK-30D, RKL-30A, RKL-30C, RKL-30D 1968
RX-16M, RX-16R, RXE-16M, RXE-16R, RXEL-16M, RXEL-16R, RXL-16M, RXL-16R 1968
V4T-14B, V4TL-14B 1968

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 298-5564 T40 Torx Socket 1
C 5F-4764 Pry Bar 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Remove and Install" for the correct procedure. Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Use a deep socket in order to remove the electrical connections from the electronic unit injectors. Use of incorrect tooling will result in damage to the electronic unit injectors.
Note: Put identification marks on all hoses, on all hose assemblies, on wires and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. Plugging all hose assemblies and tube assemblies helps to prevent fluid loss and helps to keep contaminants from entering the system.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g01416992
Typical Example
Use Tooling (A) in order to rotate the crankshaft until rocker arms (1) for the appropriate cylinder are in the correct position in order to adjust the valve lash. Refer to Systems Operation, Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure.
Follow Step 4.a through Step 4.d in order to gain access to the electronic unit injector.
Make a temporary mark on valve bridges (5) (not shown) in order to show the location and orientation. Note: Identification will ensure that the valve bridges can be reinstalled in the original location and the original orientation.
Loosen nuts (3) for the appropriate cylinder. Unscrew adjusters (2) for the appropriate cylinder until pushrods (4) can be withdrawn from the balls of the adjusters.
Withdraw the cups of pushrods (4) from the balls of adjusters (2).
Remove valve bridges (5) (not shown) from the cylinder head. Note: Do not interchange the location or the orientation of used valve bridges.
Illustration 2 g01247489
Typical example
Loosen banjo bolt (7) sufficiently in order to allow the fuel to drain from tube assembly (6).
Illustration 3 g01255699
The rocker shaft is not shown for clarity.
Remove the fuel injection line and remove seal (8) from the appropriate electronic unit injector (11). Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove" for the correct procedure. Note: Cap all open ports immediately with new caps.
Use a deep socket to remove connections (10) from electronic unit injector (11).
Slide rocker arms (1) to one side in order to gain access to torx screw (12). Use Tooling (B) in order to remove the torx screw from clamp (13). Note: Tooling (B) must be used to ensure no damage to the rocker arms.
Place a temporary identification mark on the original electronic unit injector. The electronic unit injector must be reinstalled in the original location in the cylinder head.


Parts strap JOHNSON:

0310378
 
0310378 STRAP,Stern bracket
25E79R, 33E69A, 33E69A, 33E70M, 33E70M, 35E79A, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40E74S, 40E75C, 40E76A, 40ES69R, 40ES70A, 40R69R, 40R70A, D25RWA, J20CRCCA, J20CRCDC, J20CRCEM, J20CRCOS, J20CRCUR, J20CREIE, J20CREND, J20CRESB, J25ECCM, J25ECDR
0204130
 
0204130 STRAP, Bracket
40ES69R, 40ES70A, RK-30A
0305021
Back to top