0115239 SUPPORTING BRACKET JOHNSON
BJ2REDE, BJ2REUD, BJ3ROEDE, BJ3ROEUD, HJ2DRETC, HJ3REIC, HJ3RENR, HJ3RETC, J2RECS, J2REEC, J2ROEOB, J2RTSIA, J2RTSSR, J2WREES, J2WRSIR, J2WRSSC, J3REEC, J3ROECS, J3ROEOB, J3RSDE, J3RSNF, J3RSOD, J3RSRE, J3RSTB, J3RTLSIA, J3RTLSSR, J3WREES, J3WRSIR, J
SUPPORTING
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- STERN BRACKET & SWIVEL BRACKET » 0115239
BJ3ROEDE, HJ3ROEDE, HJ3RSA, J3ROEDE, SJ3ROEDE 1996
BJ3ROEUD, HJ3ROEUD, HJ3RSK, J3ROEUD, SJ3ROEUD 1997
HJ2DRERM, HJ2DRETC 1993,1994
HJ3REIC 1991
HJ3RENR 1992
HJ3RERM, HJ3RETC 1993,1994
J2RECS, J2RSS 1998
J2REEC 1999
J2ROEOB 1995
J2RTSIA, J2RTVSIA 2001
J2RTSSR 2000
J2WREES 1999
J2WRSIR 2001
J2WRSSC 2000
J3REEC, J3RLEEC 1999
J3ROECS, J3ROLECS, J3RSS 1998
J3ROEOB 1995
J3RSDE 2006
J3RSNF 2002
J3RSOD 2005
J3RSRE 2004
J3RSTB, J3RSTF 2003
J3RTLSIA, J3RTSIA, J3RTVSIA 2001
J3RTLSSR, J3RTSSR 2000
J3WREES 1999
J3WRSIR 2001
J3WRSSC 2000
Information:
1. Remove oil supply tube (3). Disconnect oil return tube (4) from bottom of turbocharger.2. Remove four bolts and exhaust elbow (2). Remove coupling (1).3. Remove the bolts that hold turbocharger (5) to the exhaust manifold.4. Disconnect turbocharger from elbows and remove turbocharger from engine.Install Turbocharger
1. Put grease on the O-ring seals (2).2. Put 9M3710 Anti-Seize Compound on threads of turbocharger bolts.3. Install a new turbocharger gasket.4. Put the turbocharger (1) in position on the exhaust manifold. Install turbocharger bolts. Tighten bolts to a torque of 40 4 lb.ft. (5.5 0.7 mkg). 5. Inspect the piston ring-type seals on coupling. Install coupling (3) and exhaust elbow (6).6. Connect oil return line (5) to turbocharger. Install oil supply line (4).end by: a) install hoodDisassemble Turbocharger
start by: a) remove turbocharger1. Put the turbocharger in position on tool (A).2. Put a mark on the compressor cover and housings for installation purposes. 3. Remove "V" clamp (2) and remove compressor cover (1). 4. Remove "V" clamp (3) and remove shaft housing from turbine housing (4). 5. Put shaft housing in tool (B). Remove nut and compressor wheel (5) from the shaft.
When loosening the nut, do not put a side force on the shaft.
6. Remove shaft housing from tool (B) and remove turbine wheel (7) and shaft from housing.7. Remove seal ring (6) from the turbine wheel. 8. Remove snap ring and insert (8) from the housing. 9. Push the sleeve (9) out of the insert. Remove the two seal rings from the sleeve. 10. Remove deflector (10), ring (15), sleeve (11), bearing (12), ring (16), snap ring (13), bearing (17) and snap ring (14) from the housing. Remove snap rings (13) and (14) with tool (C). Check the oil hole in bearing (12). If the oil hole is not open this will cause a bearing failure.11. Turn the housing around and remove snap ring (18) and shroud (22). 12. Remove snap ring (19), sleeve (20), bearing (21), and snap ring (23). Remove the two snap rings with tool (C).13. Inspect all parts and install new parts as needed.Assemble Turbocharger
1. Make sure all oil passages are open and clean. Put clean engine oil on all parts before assembly. 2. Install snap ring (4), bearing (3), sleeve (2) and snap ring (1). Install the two snap rings with tool (A). Install the snap rings with the round side toward the bearing. 3. Install shroud (5) on the housing. Turn the shroud to make sure it is down on the housing even. The high part (web) (6) on shroud, will keep the shroud from turning on the housing after assembly.4. Install snap ring that holds the shroud in place.5. Install the bearing and two snap rings in the compressor end of the housing. Install the snap rings with tool (A). Install the snap rings with the round side toward the bearing. 6. Install seal ring (7) on the shaft. Install turbine wheel (8) and shaft in the housing.7. Put housing in position on tool (B). 8. Install ring (13), bearing (11), sleeve (12), ring (10) and deflector (9) in the housing.
The oil hole in bearing (11) must be open and clean.
9. Install the seal rings on sleeve (15). Install sleeve in insert (14). 10. Install insert in the housing and install snap ring (17).11. Install compressor wheel (16) on shaft. 12. Put clean engine oil on the threads of the shaft. Install the nut (18) and tighten to a torque of 15 1 lb.ft. (2.1 0.14 mkg).
When tightening nut do not put a side force on the shaft.
13. Install shaft housing into the turbine housing. Install "V" clamp (21) and tighten clamp to a torque of 120 lb.in. (138.4 cm.kg).14. Install compressor cover (19) and "V" clamp (20). Tighten "V" clamp to a torque of 120 lb.in. (138.4 cm.kg).end by: a) install turbocharger
1. Put grease on the O-ring seals (2).2. Put 9M3710 Anti-Seize Compound on threads of turbocharger bolts.3. Install a new turbocharger gasket.4. Put the turbocharger (1) in position on the exhaust manifold. Install turbocharger bolts. Tighten bolts to a torque of 40 4 lb.ft. (5.5 0.7 mkg). 5. Inspect the piston ring-type seals on coupling. Install coupling (3) and exhaust elbow (6).6. Connect oil return line (5) to turbocharger. Install oil supply line (4).end by: a) install hoodDisassemble Turbocharger
start by: a) remove turbocharger1. Put the turbocharger in position on tool (A).2. Put a mark on the compressor cover and housings for installation purposes. 3. Remove "V" clamp (2) and remove compressor cover (1). 4. Remove "V" clamp (3) and remove shaft housing from turbine housing (4). 5. Put shaft housing in tool (B). Remove nut and compressor wheel (5) from the shaft.
When loosening the nut, do not put a side force on the shaft.
6. Remove shaft housing from tool (B) and remove turbine wheel (7) and shaft from housing.7. Remove seal ring (6) from the turbine wheel. 8. Remove snap ring and insert (8) from the housing. 9. Push the sleeve (9) out of the insert. Remove the two seal rings from the sleeve. 10. Remove deflector (10), ring (15), sleeve (11), bearing (12), ring (16), snap ring (13), bearing (17) and snap ring (14) from the housing. Remove snap rings (13) and (14) with tool (C). Check the oil hole in bearing (12). If the oil hole is not open this will cause a bearing failure.11. Turn the housing around and remove snap ring (18) and shroud (22). 12. Remove snap ring (19), sleeve (20), bearing (21), and snap ring (23). Remove the two snap rings with tool (C).13. Inspect all parts and install new parts as needed.Assemble Turbocharger
1. Make sure all oil passages are open and clean. Put clean engine oil on all parts before assembly. 2. Install snap ring (4), bearing (3), sleeve (2) and snap ring (1). Install the two snap rings with tool (A). Install the snap rings with the round side toward the bearing. 3. Install shroud (5) on the housing. Turn the shroud to make sure it is down on the housing even. The high part (web) (6) on shroud, will keep the shroud from turning on the housing after assembly.4. Install snap ring that holds the shroud in place.5. Install the bearing and two snap rings in the compressor end of the housing. Install the snap rings with tool (A). Install the snap rings with the round side toward the bearing. 6. Install seal ring (7) on the shaft. Install turbine wheel (8) and shaft in the housing.7. Put housing in position on tool (B). 8. Install ring (13), bearing (11), sleeve (12), ring (10) and deflector (9) in the housing.
The oil hole in bearing (11) must be open and clean.
9. Install the seal rings on sleeve (15). Install sleeve in insert (14). 10. Install insert in the housing and install snap ring (17).11. Install compressor wheel (16) on shaft. 12. Put clean engine oil on the threads of the shaft. Install the nut (18) and tighten to a torque of 15 1 lb.ft. (2.1 0.14 mkg).
When tightening nut do not put a side force on the shaft.
13. Install shaft housing into the turbine housing. Install "V" clamp (21) and tighten clamp to a torque of 120 lb.in. (138.4 cm.kg).14. Install compressor cover (19) and "V" clamp (20). Tighten "V" clamp to a torque of 120 lb.in. (138.4 cm.kg).end by: a) install turbocharger