5030823 JOHNSON SWITCH, Neutral

Table 1
Diagnostic Codes Table    
Description    Conditions which Generate this Code    System Response    
261-11 Engine Timing Offset fault     The wiring to the sensors has the wrong polarity.     The code is logged.    
261-13 Engine Timing Calibration calibration required     A timing calibration is required for a new engine, replacing an Electronic Control Module (ECM) that fails to communicate or following work on the front gear train, the camshaft, or the crankshaft.     The code is logged.    If a 261-11 diagnostic code is active, verify that the wiring is installed correctly to the engine speed/timing sensors.The ECM has the ability to calibrate the mechanical differences between the Top Center (TC) of the flywheel and the TC of the timing gear on the camshaft. A magnetic transducer signals the TC of the flywheel to the ECM when a notch on a counterweight passes by the transducer. The engine speed/timing sensor signals the TC of the timing gear to the ECM. Any offset between the TC of the flywheel and the TC of the timing gear is stored into the memory of the ECM.Note: A timing calibration will not increase the available engine power.Table 2 lists the special tools that are required in order to perform this procedure.
Table 2
Required Special Tools    
Part Number    Description    
7X-1171     Transducer Adapter    
6V-2197     Transducer    
7X-1695     Cable As    
170-3519     Harness (1)    
( 1 ) This item is not required if the engine harness has a connector for timing calibration.Test Step 1. Timing Calibration
Install the Transducer Adapter
Remove the electrical power from the ECM.
Use the appropriate engine turning tool to put either the No. 1 piston or the No. 6 piston at top center. Refer to the Systems Operation/Testing and Adjusting.
Refer to Table 3. After the top center position has been located, rotate the crankshaft for the number of degrees that is applicable to your engine model. Be sure to rotate the crankshaft in the direction of rotation that is specified in the Table.
Table 3
Crankshaft Rotation    
Engine Model     Number of Degrees    Direction of Rotation    
C7     100     Normal Rotation    
C-9     85     Normal Rotation    
C-10     60     Opposite Normal Rotation    
C11     75     Normal Rotation    
C-12     60     Opposite Normal Rotation    
C13     75     Normal Rotation    
C-15     60     Opposite Normal Rotation    
C15     60     Opposite Normal Rotation    
C-16     60     Opposite Normal Rotation    
C18     30     Opposite Normal Rotation    
Refer to Table 4. Locate the engine timing calibration port.
Table 4
Location of the Timing Calibration Port    
Engine Model    Crankshaft Counterweight    Engine Location    
C7     3     Left Side    
C-9     3     Left Side    
C-10     8     Right Side    
C11     8     Left Side    
C-12     8     Right Side    
C13     8     Left Side    
C-15     2     Left Side    
C15     2     Left Side    
C-16     2     Left Side    
C18     2     Left Side    
Remove the plug from the timing calibration port.
Thread the transducer adapter into the port.Continue to the next test step.
Install the Transducer.
If the crankshaft is not in the correct position when the transducer is installed, the transducer will be damaged when the engine is started.
Apply clean engine oil to a 2D-6392 O-Ring Seal . Install the O-ring seal on the end of the 6V-2197 Transducer .
Push the transducer through the transducer adapter until the transducer contacts the crankshaft counterweight.
Withdraw the transducer 1.0 mm (0.04 inch) and hand tighten the nut on the adapter sleeve in order to secure the transducer. Move the O-ring seal against the adapter.Continue to the next test step.
Connect the 7X-1695 Cable As .
If the engine harness is equipped with a connector for timing calibration, connect the 7X-1695 Cable As to the connector for timing calibration and to the transducer.
If the engine harness is not equipped with a connector for timing calibration, perform the following procedure:Disconnect the P2 connector from the ECM.Determine the number of terminals on the P2 connector.Refer to Table 5. Remove the sealing plugs from the appropriate terminals. Do not discard the sealing plugs. The sealing plugs may be reinstalled when the timing calibration is complete.
Table 5
P2 Locations for Connection of the 7X-1695 Cable As    
Wire Color     70 pin Connector