0389334 JOHNSON SWIVEL BRACKET


0389334 SWIVEL BRACKET JOHNSON 70EL78C, 70EL79R, 75ELR78C, 75ELR79R, J60ELCDS, J65RWLCRS, J65WMLCDR, J65WMLCOC, J70ELCDC, J70ELCIH, J70ELCNB, J70ELCOS, J70ELCRD, J70ELCSA, J70ELCTE, J75ECDC, J75ECNB, J75ECOS, J75ECRD, J75ECTE, J75ERCIH, J75ERCSA SWIVEL
0389334 SWIVEL BRACKET JOHNSON
Rating:
98

Buy SWIVEL BRACKET 0389334 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP JOHNSON entire parts catalog list:

70EL78C 1978
70EL79R 1979
75ELR78C, 75ER78C 1978
75ELR79R, 75ER79R 1979
J60ELCDS, J60TLCDS 1986
J65RWLCRS, J65TELCRS, J65WTLCRS 1984
J65WMLCDR 1986
J65WMLCOC, J65WTLCOC 1985
J70ELCDC, J70TLCDC 1986
J70ELCIH, J70ELCIM, J70TLCIM 1981
J70ELCNB, J70TLCNB 1982
J70ELCOS, J70TLCOS 1985
J70ELCRD, J70TLCRD 1984
J70ELCSA 1980
J70ELCTE, J70TLCTE 1983
J75ECDC 1986
J75ECNB, J75ELCNB, J75TLCNB 1982
J75ECOS 1985
J75ECRD, J75ELCRD, J75TLCRD 1984
J75ECTE, J75ELCTE, J75TLCTE 1983
J75ERCIH, J75ERCIM, J75ERLCIH, J75ERLCIM, J75TELCIM, J75TRLCIH 1981
J75ERCSA, J75ERLCSA, J75TRLCSA 1980

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 243 Thread Lock 1
B - Loctite 275 Thread Lock 1
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03343543Note: The position of fuel screw (17) controls the emissions of the engine. Ensure correct adjustment of the fuel screw. Refer to Systems Operation, Testing and Adjusting, "Governor - Adjust" for the correct procedure.
If the original housing has been replaced with a new housing, follow Step 1.a through Step 1.e in order to install fuel screw (17).
Install fuel screw (17) to housing (3).
Install a new sealing washer (18) to fuel screw (17).
Loosely install locknut (19) to fuel screw (17). The procedure that is used to set the position of the fuel screw is described in Systems Operation, Testing and Adjusting, "Governor - Adjust" for the correct procedure.
Do not install the tamper proof cap (20) until fuel screw (17) adjustment has been completed.
Install a new emissions label to front housing (3).
Illustration 2 g03343542
Illustration 3 g03343540
Place lever assembly (12) in position in front housing (3) and install shaft (11). Note: Ensure the correct orientation of the lever assembly.
Install a new sealing washer (14) to the treads of shaft (11).
Install nut (15). Tighten the nut to a torque of 6 N m (53 lb in).
Connect spring (13) to front housing (3).
Install a new silicon rubber bung (16).
Illustration 4 g03343538
If the engine is equipped with an angleich unit, follow Steps 7.a and 7.b in order to install the angleich unit.
Apply Tooling (B) to the first two threads of angleich unit (10).
Install angleich unit (10) to lever assembly (7). Tighten the angleich unit to a torque of 6 N m (53 lb in). Note: Ensure that Tooling (B) is not allowed to contaminate the plunger assembly of the angleich unit. Contamination of the plunger assembly will render the angleich unit inoperative.
Illustration 5 g03343536
Install a new sealing washer (8) to shaft (9).
Apply Tooling (A) to the first two threads of shaft (9).
Place lever assembly (7) in position in front housing (3) and install shaft (9). Tighten the shaft to a torque of 16 N m (142 lb in). Note: Ensure the correct orientation of the lever assembly.
Illustration 6 g03343535
Position a new gasket (6) (not shown) onto throttle control (1).
Position the assembly of throttle control (1) into front housing (3).
Install bolts (5). Tighten the bolts to a torque of 10 N m (89 lb in).
Illustration 7 g03343534
Install spring (4).
If the position of the fuel screw has been altered, the fuel screw must be reset. Refer to Systems Operation, Testing and Adjusting, "Governor - Adjust" for the correct procedure.
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) Install" for the correct procedure.
After fuel screw (17) has been adjusted, to the procedure in Systems Operation, Testing and Adjusting, "Governor - Adjust". Install a new tamper proof cap (20) to nut (19). Refer to Illustration 1.


Parts swivel JOHNSON:

0383146
 
0383146 SWIVEL BRACKET, Std
55ES69A, 60ES70B, 60ES71C, 65ES72S, 65ES73R, 70EL77S, 70EL78C, 70EL79R, 70ES74M, 70ES75B, 75ELR76D, 75ELR77S, 75ELR78C, 75ELR79R, 75ESLR75B, J60ELCDS, J60ELCUC, J70ELCIH, J70ELCNB, J70ELCOS, J70ELCRD, J70ELCSA, J70ELCTE, J75ECCA, J75ECDC, J75ECNB, J7
0394266
 
0394266 SWIVEL BRACKET
J65RWLCDR, J65RWLCOC, J65RWLCRS
Back to top