0396962 JOHNSON SWIVEL BRACKET


0396962 SWIVEL BRACKET JOHNSON BJ50DTLEDC, BJ50DTLEUR, BJ60ELEDR, BJ60ELEUA, BJ60TLECM, BJ70ELECB, BJ70ELEDA, BJ70ELEUM, J50DTLECA, J50DTLEOS, J60ELCCR, J60ELCEA, J60ELEIB, J60ELENE, J60ELEOC, J60ELERS, J60ELESM, J60ELETD, J65WELEES, J65WELSIR, J65WELSSC, J65WMLEIB, J65WMLENE, J65 SWIVEL
0396962 SWIVEL BRACKET JOHNSON
Rating:
8

Buy SWIVEL BRACKET 0396962 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP JOHNSON entire parts catalog list:

BJ50DTLEDC, J50DTLEDC, J50ELED 1996
BJ50DTLEUR, J50DTLEUR, J50ELEUR 1997
BJ60ELEDR, BJ60TLEDR, J60ELEDR, J60TLEDR, SJ60TLEDR 1996
BJ60ELEUA, BJ60TLEUA, J60ELEUA, J60TLEUA 1997
BJ60TLECM, J60TLECM 1998
BJ70ELECB, BJ70TLECB, J70TLECB 1998
BJ70ELEDA, BJ70TLEDA, HJ70TXEDA, J70TLEDA, SJ70TLEDA 1996
BJ70ELEUM, BJ70TLEUM, HJ70TXEUM, J70TLEUM 1997
J50DTLECA 1998
J50DTLEOS, J50ELEOS 1995
J60ELCCR, J60TLCCR, J60TTLCCR 1988
J60ELCEA, J60TLCEA, J60TTLCEA, TJ60TLCEA, TJ60TLESF 1989
J60ELEIB, J60TLEIB, TJ60TLEIB, VJ60ELEIB, VJ60TLEIB 1991
J60ELENE, J60TLENE, TJ60TLENE, VJ60ELENE, VJ60TLENE 1992
J60ELEOC, J60TLEOC 1995
J60ELERS, J60ELERV, J60TLERS, J60TLERV 1994
J60ELESM, J60TLESM, J60TTLESM, TJ60TLESF, TJ60TLESM, VJ60ELESM, VJ60TLESM 1990
J60ELETD, J60TLETD, TJ60TLETD, VJ60ELETD 1993
J65WELEES 1999
J65WELSIR 2001
J65WELSSC 2000
J65WMLEIB 1991
J65WMLENE 1992
J65WMLEOC 1995
J65WMLERS 1994
J65WMLESM 1990
J65WMLETD 1993
J65WMLZ 1989
J70ELCCA, J70TLCCA 1988
J70ELCEM, J70TLCEM, TJ70TLCEM, TJ70TLESF 1989
J70ELEIE, J70TLEIE, VJ70ELEIE, VJ70TLEIE 1991
J70ELEND, J70TLEND, VJ70ELEND, VJ70TLEND 1992
J70ELEOR, J70JLEOS, J70TLEOR 1995
J70ELERC, J70ELERV, J70TLERC, J70TLERV 1994
J70ELESB, J70TLESB, TJ70TLESB, TJ70TLESF, VJ70ELESB, VJ70TLESB 1990
J70ELETS, J70TLETS, VJ70ELETS, VJ70TLETS 1993
N65WMLM 1988
SJ65WMLD, SJ65WMYD 1998
SJ65WMLM, SJ65WMYM 1996
SJ65WMLZ2, SJ65WMYZ2 1997

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 487-3130 Engine Turning Tool 1 Start By:
Remove oil pan.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g06069666
Install Tooling (A). Use Tooling (A) to turn the crankshaft until the connecting rod bearing caps are accessible.
Illustration 2 g06069704
Mark connecting rod (3) and connecting rod cap (1) for identification and location.Note: This engine has fractured connecting rods. Fractured connecting rods must be handled with care. Use a soft faced hammer to tap the connecting rod cap, if necessary.Note: Do not place the fractured faces of the connecting rod cap on any surface. The connecting rod cap must be laid flat on the side to prevent damage to the fractured faces of the connecting rod cap.
Remove connecting rod cap bolts (2) and connecting rod cap (1) from connecting rod (3).
Illustration 3 g01139029
Remove the lower half of connecting rod bearing (5) from connecting rod cap (1).
Push connecting rod (3) away from the crankshaft. Remove the upper half of connecting rod bearing (4) from connecting rod (3).Note: Do not damage the fractured faces of the connecting rod. Place a suitable protective cap on the ends of the connecting rod to prevent damage to the fractured faces of the connecting rod.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The joint between the connecting rod and the connecting rod cap is produced by fracturing. The connecting rod assembly must be handled with care in order to avoid damage to the mating surfaces. The connecting rod assembly must be replaced if any damage occurs to the mating surfaces. New connecting rod assemblies come with the connecting rod caps bolted on the connecting rod.Use only a soft faced hammer to tap the connecting rod cap when separating the connecting rod cap from the connecting rod.Failure to use a soft faced hammer may result in damage to the fractured surfaces of the connecting rod assembly.
Use Tooling (A) to turn the crankshaft until the connecting rod and bearing cap mating surfaces are accessible.
Illustration 4 g01139029Note: Install the connecting rod bearings dry when clearance checks are performed. Apply clean engine oil to the connecting rod bearings for final assembly.
Remove the protective caps from the end of the connecting rod and install the upper half of connecting rod bearing (4). Ensure that the bearing tab engages with the slot in connecting rod (3).
Pull the piston and connecting rod assembly onto the crankshaft.
Install the lower half of connecting rod bearing (5) into connecting rod cap (1). Ensure that the bearing tab engages with the slot in connecting rod cap (1).Note: Do not place the fractured faces of the connecting rod cap on any surface. The connecting rod cap must be laid flat on the side to prevent damage to the fractured faces of the connecting rod cap.
Install connecting rod cap (1) and connecting rod cap bolts (2). Lubricate threads of connecting rod bolts (2) with clean engine oil.
Check the bearing clearance. Refer to Disassembly and Assembly, "Bearing Clearance - Check".
Tighten connecting rod cap bolts (2) to a torque of 70 4 N m (52 3 lb ft).
Place an index mark on each connecting rod cap bolt (2). Tighten each bolt for an extra 60 3 degrees (1/4 turn).
Use Tooling (A) to rotate the crankshaft to ensure that the crankshaft turns freely.


Parts swivel JOHNSON:

0396961
 
0396961 SWIVEL BRACKET
J50TTLECA, J50TTLEDC, J50TTLEOS, J50TTLEUR, J60ELCCR, J60ELCEA, J60ELESM, J60TTLECM, J60TTLEDR, J60TTLEIB, J60TTLENE, J60TTLEOC, J60TTLERS, J60TTLETD, J60TTLEUA, J65RSLC, J65RSLM, J65RSLZ2, J65WRLEEO, J65WRLSIR, J65WRLSSC, J70TTLEIE, J70TTLEND, J70TT
0433466
 
0433466 SWIVEL BRACKET
J100STLEIE, J115JLEIE, J120TLAIE, J140CXEIA, J60ELEIB, J70ELEIE, J88MSLEIM, J88MSLEIM
0435005
SWIVEL BRACKET
0435005 SWIVEL BRACKET
BJ115ELEDR, BJ115ELEUA, BJ115GLECM, BJ115PLEEM, BJ115TLEDA, BJ130PLEED, BJ130TLECE, BJ130TLEDM, BJ130TLEUB, BJ50DTLEDC, BJ50DTLEUR, BJ60ELEDR, BJ60ELEUA, BJ60TLECM, BJ70ELECB, BJ70ELEDA, BJ70ELEUM, BJ70PLEEE, BJ70PLSIS, BJ90ELEDR, BJ90ELEUA, BJ90PLEE
Back to top