0310820 TRANSOM PLATE 5" EXTENSION KIT JOHNSON
1R69C, 1R70R, 2R71A, 2R72M, 2R73B, 2R74E, 2R75D, 2R76S, 2R77C, 2R78R, 2R79A, J2RCIB, J2RCNE, J2RCOC, J2RCRS, J2RCSM, J2RCTD, JCO-CCM, JCO-CDR, JCO-CEB, JCO-CUA, JCO-ESE
TRANSOM
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
BRP JOHNSON entire parts catalog list:
- GEARCASE GROUP » 0310820
2R71A 1971
2R72M 1972
2R73B 1973
2R74E 1974
2R75D 1975
2R76S 1976
2R77C 1977
2R78R 1978
2R79A 1979
J2RCIB 1981
J2RCNE 1982
J2RCOC 1985
J2RCRS 1984
J2RCSM 1980
J2RCTD 1983
JCO-CCM 1988
JCO-CDR 1986
JCO-CEB 1989
JCO-CUA 1987
JCO-ESE 1990
Information:
3. Remove four bolts (1) and remove elbow (2). 4. Disconnect hose (3) from the turbocharger. Cap and plug all openings immediately. 5. Disconnect hose (4), tubes (6) and line (5) from the turbocharger. Remove two bolts (7) from the oil return tube. 6. Loosen the hose clamps (10) and disconnect the air inlet hose. Install lifting sling (9), remove four bolts (11) and remove turbocharger (8). The weight of the turbocharger is approximately 36 kg (80 lb). The following steps are for installation of the turbocharger.7. Make sure the studs are tightened in the exhaust manifold assembly to a torque of 25 4 N m (20 3 lb ft).8. Install the gasket on the exhaust manifold assembly.9. Fasten a suitable lifting device and put the turbocharger in position. Put 5P-3931 Anti-Seize Compoundon the threads of the studs and nuts (11). Install the nuts and tighten them to a torque of 54 5.5 N m (40 4.00 lb ft).10. If necessary, make a replacement of the O-ring seals on elbow (2) and put clean engine oil on them. Put 4C-5598 Anti-Seize Compound on the threads of the bolts that hold elbow (2) to the inlet manifold. Install elbow (2).11. Install the air inlet hose and tighten clamps (10). Position oil return tube and install bolts (7). Connect two tubes (6) and line (5). Install two hoses (3) and (4). For more detailed information regarding the turbocharger, see the topic "Turbocharger" in the Specifications Manual.12. Fill the cooling system with coolant to the correct level. Refer to the Operation & Maintenance Manual for this procedure.Disassemble & Assemble Turbocharger
Start By:a. remove turbocharger FLUID SPILLAGE CONTAINMENT Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. 1. Install turbocharger in Tool Group (A). Put marks on the three housings of the turbocharger for correct installation and alignment at assembly. Loosen "V" clamp (2) and remove compressor housing (1).2. Loosen "V" clamp (3). Remove cartridge housing (4) from turbine housing (5). 3. Put the cartridge assembly in Tool (B) as shown.
do not put a side force on the shaft.
4. Use Tool (C) and remove the nut that holds compressor wheel (6). Remove compressor wheel (6). 5. Remove turbine shaft (7) from the cartridge housing. 6. Remove seal ring (9) and shroud (8) from turbine shaft (7). 7. Use Tool (D) and remove ring (11) that holds insert (10) in the cartridge housing. 8. Remove insert (10) with Tooling (E). 9. Remove O-ring seal (13) and sleeve (12) from insert (10). Remove the seal ring from sleeve (12). 10. Remove deflector (14) and ring (15). 11. Remove bearing (16), sleeve (17) and ring (18). The dye marks put on bearings (19) and (20) are used for identification of the bearings when they are installed.12. Use Tool (F) and remove the ring that holds bearing (19) in position. Remove bearing (19) and put a long dye mark on the top face of the bearing. 13. Turn the cartridge assembly over. Use Tool (F) and remove the ring that holds bearing (20) in position. Remove bearing (20) from the cartridge housing. Put a short dye mark on the top face of bearing (20).14. If necessary, remove the two rings that hold the bearings in position from the cartridge housing with Tool (F).15. Check all parts of the turbocharger for damage. If the parts have damage, use new parts for replacement. See Special Instruction, SMHS6854 for Turbocharger Reconditioning. Also see Guideline For Reusable Parts, SEBF8018. The following steps are for assembly of the turbocharger.16. Make sure all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material.17. Put clean engine oil on all parts of the cartridge assembly. Install the rings that hold the bearings in position with the round edges of the rings toward the bearings.18. Make a replacement of the two inside rings that hold the bearings in position in the cartridge housing if necessary.19. Install bearing (20) with the short dye mark up. Use Tool (F) to install the ring to hold the bearing in position.20. Turn the cartridge assembly over and install bearing (19) with the long dye mark up. Use Tool (F) and install the ring to hold the bearing in position.
Make sure the oil hole in bearing (16) is open and clean to prevent a bearing failure.
21. Install ring (18), sleeve (17) and bearing (16).22. Install ring (15) and deflector (14).23. Install O-ring seal (13) around insert (10).24. Install the seal ring on sleeve (12).25. Install sleeve (12) in insert (10) from the bottom side.26. Install insert (10) in the cartridge housing. Use Tool (D) and install ring (11) to hold the insert in position.27. Put turbine shaft (7) in position in Tool (B). Put Loctite LB 8632 Silicone Lubricant (North America), Loctite LB 8104 Silicone Lubricant (EAME), Loctite LB 8801 Silicone Lubricant (Asia Pacific Division), or Loctite LB Superlube (South America)in the groove for seal ring (9). Make sure the grease fills the groove approximately one half or more of the groove depth for the complete circumference of the groove to help make a carbon dam under the seal ring. Install seal ring (9) and shroud (8) on turbine shaft (7).28. Install the cartridge housing on turbine shaft (7). Make sure seal ring (9) is fitted correctly in the cartridge housing.
Do not put a side force on turbine shaft (7) when the nut is tightened.
29. Install compressor wheel (6) on the turbine shaft. Put clean engine oil on the threads of the turbine shaft. Install the nut that holds the compressor wheel on the turbine shaft. Use
Start By:a. remove turbocharger FLUID SPILLAGE CONTAINMENT Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. 1. Install turbocharger in Tool Group (A). Put marks on the three housings of the turbocharger for correct installation and alignment at assembly. Loosen "V" clamp (2) and remove compressor housing (1).2. Loosen "V" clamp (3). Remove cartridge housing (4) from turbine housing (5). 3. Put the cartridge assembly in Tool (B) as shown.
do not put a side force on the shaft.
4. Use Tool (C) and remove the nut that holds compressor wheel (6). Remove compressor wheel (6). 5. Remove turbine shaft (7) from the cartridge housing. 6. Remove seal ring (9) and shroud (8) from turbine shaft (7). 7. Use Tool (D) and remove ring (11) that holds insert (10) in the cartridge housing. 8. Remove insert (10) with Tooling (E). 9. Remove O-ring seal (13) and sleeve (12) from insert (10). Remove the seal ring from sleeve (12). 10. Remove deflector (14) and ring (15). 11. Remove bearing (16), sleeve (17) and ring (18). The dye marks put on bearings (19) and (20) are used for identification of the bearings when they are installed.12. Use Tool (F) and remove the ring that holds bearing (19) in position. Remove bearing (19) and put a long dye mark on the top face of the bearing. 13. Turn the cartridge assembly over. Use Tool (F) and remove the ring that holds bearing (20) in position. Remove bearing (20) from the cartridge housing. Put a short dye mark on the top face of bearing (20).14. If necessary, remove the two rings that hold the bearings in position from the cartridge housing with Tool (F).15. Check all parts of the turbocharger for damage. If the parts have damage, use new parts for replacement. See Special Instruction, SMHS6854 for Turbocharger Reconditioning. Also see Guideline For Reusable Parts, SEBF8018. The following steps are for assembly of the turbocharger.16. Make sure all of the oil passages in the turbocharger cartridge housing are clean and free of dirt and foreign material.17. Put clean engine oil on all parts of the cartridge assembly. Install the rings that hold the bearings in position with the round edges of the rings toward the bearings.18. Make a replacement of the two inside rings that hold the bearings in position in the cartridge housing if necessary.19. Install bearing (20) with the short dye mark up. Use Tool (F) to install the ring to hold the bearing in position.20. Turn the cartridge assembly over and install bearing (19) with the long dye mark up. Use Tool (F) and install the ring to hold the bearing in position.
Make sure the oil hole in bearing (16) is open and clean to prevent a bearing failure.
21. Install ring (18), sleeve (17) and bearing (16).22. Install ring (15) and deflector (14).23. Install O-ring seal (13) around insert (10).24. Install the seal ring on sleeve (12).25. Install sleeve (12) in insert (10) from the bottom side.26. Install insert (10) in the cartridge housing. Use Tool (D) and install ring (11) to hold the insert in position.27. Put turbine shaft (7) in position in Tool (B). Put Loctite LB 8632 Silicone Lubricant (North America), Loctite LB 8104 Silicone Lubricant (EAME), Loctite LB 8801 Silicone Lubricant (Asia Pacific Division), or Loctite LB Superlube (South America)in the groove for seal ring (9). Make sure the grease fills the groove approximately one half or more of the groove depth for the complete circumference of the groove to help make a carbon dam under the seal ring. Install seal ring (9) and shroud (8) on turbine shaft (7).28. Install the cartridge housing on turbine shaft (7). Make sure seal ring (9) is fitted correctly in the cartridge housing.
Do not put a side force on turbine shaft (7) when the nut is tightened.
29. Install compressor wheel (6) on the turbine shaft. Put clean engine oil on the threads of the turbine shaft. Install the nut that holds the compressor wheel on the turbine shaft. Use