0328156 JOHNSON TUBE, Crankcase drain


0328156 TUBE, Crankcase drain JOHNSON J5RHCNR, J5RHCTA, J6RCDE, J6RCOB, J6RCRM, J6RCUD, J8RCDE, J8RCNR, J8RCOB, J8RCRM, J8RCTA, J8RCUD TUBE
0328156 TUBE, Crankcase drain JOHNSON
Rating:
88

Buy TUBE, Crankcase drain 0328156 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

BRP JOHNSON entire parts catalog list:

J5RHCNR, J5RHLCNR 1982
J5RHCTA, J5RHLCTA 1983
J6RCDE, J6RLCDE, J6SLCDE 1986
J6RCOB, J6RLCOB, J6SLCOB 1985
J6RCRM, J6RLCRM, J6SLCRM 1984
J6RCUD, J6RLCUD, J6SLCUD 1987
J8RCDE, J8RLCDE, J8SRLCDE 1986
J8RCNR, J8RLCNR, J8SRLCNR 1982
J8RCOB, J8RLCOB, J8SRLCOB 1985
J8RCRM, J8RLCRM, J8SRLCRM 1984
J8RCTA, J8RLCTA, J8SRLCTA 1983
J8RCUD, J8RLCUD, J8SRLCUD 1987

Information:

Drain the Cooling System
Stop the engine and allow the engine to cool. Close the water inlet for the separate circuit aftercooler (if equipped). Ensure that the engine will not start when the cooling system is drained.
Loosen the radiator filler cap slowly in order to relieve any pressure. Remove the radiator filler cap.
Illustration 1 g00750410
(1) Coolant drain
Illustration 2 g00750411
Locations of the cooling system drain plugs
(1) Oil cooler
(2) Jacket water pump
(3) Engine block Note: If the engine has a jacket water heater, drain the coolant from the heater.
Open the coolant drain. Remove the cooling system drain plugs. Allow the coolant to drain.
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by Caterpillar to reclaim the used coolant.
For information regarding the disposal and the recycling of used coolant, consult your Caterpillar dealer or consult Caterpillar Dealer Service Tools Group:Outside U.S.A. (309) 675-6277
Inside U.S.A. 1-800-542-TOOL
Inside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
CSTG COSA Geneva, Switzerland 41-22-849 40 56
Clean the Cooling System
After the cooling system has been drained, flush the cooling system with clean water in order to remove any debris.
Close the coolant drain. Clean the drain plugs and install the drain plugs.
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Open the water inlet for the separate circuit aftercooler (if equipped). Fill the cooling system with clean water. Install the radiator filler cap. Operate the engine until the temperature reaches 49 °C (120 °F) to 66 °C (150 °F).
Stop the engine and allow the engine to cool. Close the water inlet for the separate circuit aftercooler (if equipped). Ensure that the engine will not start when the cooling system is drained. Loosen the radiator filler cap slowly in order to relieve any pressure. Remove the radiator filler cap.
Open the coolant drain. Remove the drain plugs. Allow the coolant to drain. Flush the cooling system with clean water. Close the coolant drain. Install the drain plugs.
Repeat Steps 3, 4, and 5. Fill the Cooling System
Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks.
Fill the cooling system with ELC (Extended Life Coolant). After filling the cooling system, do not install the radiator filler cap.
Open the water inlet for the separate circuit aftercooler (if equipped). Start the engine. Operate the engine in order to purge the air from the cavities of the engine block. Allow the ELC to warm and allow the coolant level to stabilize. Stop the engine.
Check the coolant level. Maintain the coolant to the proper level on the sight gauge (if equipped). If a sight gauge is not equipped, maintain the coolant within 13 mm (.5 inch) below the bottom of the filler pipe.
Clean the radiator filler cap. Inspect the gaskets of the radiator cap. If the gaskets of the radiator filler cap are damaged, discard the old radiator filler cap and install a new radiator filler cap. If the gaskets of the radiator filler cap are not damaged, use a 9S-8140 Pressurizing Pump in order to pressure test the radiator filler cap. The correct pressure is stamped on the face of the radiator filler cap. If the radiator filler cap does not maintain the correct pressure, install a new radiator filler cap.
Start the engine. Inspect the cooling system for leaks and for proper operating temperature.


Parts tube JOHNSON:

0320025
 
0320025 TUBE,Water 5" LONGER PARTS
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15RELEUC, BJ5DREDS, BJ5DREUC, BJ5FRBECC, BJ5FRBEU
0328158
TUBE, Crankcase drain
0328158 TUBE, Crankcase drain
J4BRHCDE, J4BRHCOB, J4BRHCRM, J4BRHCTA, J4BRHCUD, J4RDHCDE, J4RDHCUD, J5RHCNR, J5RHCTA, J8RCNR, J8RCTA
0328159
 
0328159 TUBE, Crankcase drain
J4BRHCDE, J4BRHCOB, J4BRHCRM, J4BRHCTA, J4BRHCUD, J4RDHCDE, J4RDHCUD, J5RHCNR, J5RHCTA, J8RCNR, J8RCTA
0328157
 
0328157 TUBE, Crankcase drain
J4BRHCOB, J4BRHCRM, J5RHCNR, J5RHCTA, J6RCDE, J6RCOB, J6RCRM, J6RCUD, J8RCDE, J8RCNR, J8RCOB, J8RCRM, J8RCTA, J8RCUD
Back to top