5033515 JOHNSON WASHER (16.5X60.5X7.0mm)


5033515 WASHER (16.5X60.5X7.0mm) JOHNSON BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J140CX4SOR, J140CX4STS, J140PL4SOR, J140PL4STS, J140PX4SOR, J90PL4SOR WASHER
5033515 WASHER (16.5X60.5X7.0mm) JOHNSON
Rating:
38

Buy WASHER (16.5X60.5X7.0mm) 5033515 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

BRP JOHNSON entire parts catalog list:

BJ115L4SDA, BJ115PX4SDA, J115PL4SDA, J115PX4SDA 2006
BJ115L4SRC, BJ115X4SRC, J115PL4SRC, J115PX4SRC 2004
BJ115L4STS, BJ115X4STS, J115PL4STS, J115PX4STS 2003
BJ140CX4DR, J140CX4SDA 2006
BJ140CX4SRS, J140CX4SRC 2004
BJ140L4SDR, BJ140X4SDR, J140PL4SDA, J140PX4SDA 2006
BJ140PL4SRS, BJ140PX4SRS, J140PL4SRC, J140PX4SRS 2004
BJ90PL4SDA, BJ90PX4SDA, J90PL4SDA, J90PX4SDA 2006
BJ90PL4SRC, BJ90PX4SRC, J90PL4SRC, J90PX4SRC 2004
BJ90PL4STS, BJ90PX4STS, J90PL4STS, J90PX4STS 2003
J115PL4SOR, J115PX4SOR 2005
J140CX4SOR 2005
J140CX4STS 2003
J140PL4SOR 2005
J140PL4STS, J140PX4STS 2003
J140PX4SOR 2005
J90PL4SOR, J90PX4SOR 2005

Information:

Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps Values Results
1. Engine Oil Cooler
A. Drain the engine lubricating oil and coolant from the engine.
B. Inspect the oil cooler for signs of damage or leaks. Refer to Systems Operation, Testing and Adjusting, Engine Oil Cooler - Inspect for more information.
Oil cooler
Result: There is evidence of leaks from the oil cooler or damage to the oil cooler.
Repair: Install a new oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove" and Disassembly and Assembly, "Engine Oil Cooler - Install" for the correct procedure.
Refill the engine oil and coolant. Refer to Operation and Maintenance Manual for the correct procedure.
Result: There is no evidence of damage or leaks.
Proceed to Test Step 2.
2. Engine Water Pump
A. Inspect the water pump for signs of damage or leaks. Refer to Systems Operation, Testing and Adjusting, Water Pump - Inspect for more information.
Water pump
Result: There is evidence of leaks from the water pump or damage to the water pump.
Repair: Install a new water pump. Refer to Disassembly and Assembly, "Water Pump - Remove" and Disassembly and Assembly, "Water Pump - Install" for the correct procedure.
Refill the engine oil and coolant. Refer to Operation and Maintenance Manual for the correct procedure.
Result: There is no evidence of damage or leaks.
Proceed to Test Step 3.
3. Cylinder Head and Gasket
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove" for the correct procedure. Inspect the cylinder head gasket for faults and any signs of leakage.
B. Check the cylinder head for flatness. Refer to Systems Operation, Testing and Adjusting, "Cylinder Head - Inspect" for the correct procedure.
C. Check the mating face of the cylinder head for faults and signs of leakage. If a fault is found, replace the cylinder head. If signs of leakage are found, determine the cause of the leakage. Refer to Systems Operation, Testing and Adjusting, "Cylinder Head - Inspect" for the correct procedure.
D. Check the internal core plugs in the cylinder head for signs of leakage.
Cylinder head and gasket
Result: The cylinder head gasket is faulty or shows signs of leakage.
Repair: Check for faults in the corresponding areas of the cylinder head and cylinder block.
Result: The cylinder head is not within specification for flatness.
Repair: Install a new cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure.
Result: The cylinder head shows signs of a fault or leakage.
Repair: Install a new cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install" for the correct procedure.
Result: An internal core plug in the cylinder head shows signs of leakage.
Repair: Replace the faulty core plug.
Result: The cylinder head is OK.
Proceed to Test Step 4.
4. Cylinder Block
A. Inspect the top face of the cylinder block for faults and signs of leakage.
Cylinder block
Result: The top face of the cylinder block has a fault.
Repair: Replace the cylinder block.
Result: The top face of the cylinder block shows signs of leakage.
Repair: Determine the cause of the leakage. Refer to Systems Operation, Testing and Adjusting, "Cylinder Block - Inspect" for the correct procedure.
Result: The cylinder block is OK.
Repair: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Remove the oil filter element. Install a new engine oil filter element. Fill the engine with clean engine oil to the correct level. Refer to the Operation and Maintenance Manual, "Engine Oil and Filter - Change" for more information.
Fill the cooling system. Refer to the Operation and Maintenance Manual for more information.
If coolant is found in the oil again, contact the Dealer Solutions Network (DSN).


Parts washer JOHNSON:

5030056
 
5030056 WASHER, Fuel tank
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ25E4SDS, BJ25E4SUC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA
5030429
 
5030429 WASHER
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC,
5032555
 
5032555 WASHER (31X39X2.0mm)
BJ115L4STS, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SRR, BJ70PL4STC, BJ90PL4STS, J140CX4STS, J140PL4STS, J60PL4SNF, J70PL4SNF
5032556
WASHER
5032556 WASHER
BJ115L4STS, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SRR, BJ70PL4STC, BJ90PL4STS, J140CX4STS, J140PL4STS, J60PL4SNF, J70PL4SNF
5032635
WASHER
5032635 WASHER
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J140CX4SOR, J140CX4S
5033598
 
5033598 WASHER
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ40PL4SOC, BJ50PL4SOC, BJ60PL4SDM, BJ70PL4SDM, BJ90PL4SDA, BJ90PL4SRC, BJ90PL4STS, J115PL4SOR, J140CX4SOR, J140CX4STS, J140PL4SOR, J140PL4STS, J140PX4SOR, J90PL4SO
5034115
 
5034115 WASHER (60X85X1.3mm)
BJ140CX4DR, BJ140CX4SRS, J140CX4SOR, J140CX4STS
5034117
 
5034117 WASHER (60X85X0.8mm)
BJ140CX4DR, BJ140CX4SRS, J140CX4SOR, J140CX4STS
Back to top