0325253 JOHNSON WATER COVER, Cylinder head


0325253 WATER COVER, Cylinder head JOHNSON J10ELCID, J10ELCNS, J10ELCTC, J15ECIS, J15ECNC, J15ECTR WATER

Buy WATER COVER, Cylinder head 0325253 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

BRP JOHNSON entire parts catalog list:

J10ELCID, J10RCID, J10RLCID, J10SELCID 1981
J10ELCNS, J10RCNS, J10RLCNS, J10SELCNS 1982
J10ELCTC, J10RCTC, J10RCTR, J10RLCTC, J10RLCTR, J10SELCTC 1983
J15ECIS, J15RCIS, J15RLCIS 1981
J15ECNC, J15RCNC, J15RLCNC 1982
J15ECTR, J15ELCTR, J15RCTA, J15RCTR, J15RLCTA, J15RLCTR 1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 207-5034(1) Stud Tensioner Tool Gp 1
301-5215(2) Stud Tensioner Tool Gp 1
B 8T-0820 Hydraulic Pressure Gauge 1
3S-6224(3) Electric Hydraulic Pump 1
8S-8033(3) Electric Hydraulic Pump 1
9U-6600(3) Hand Hydraulic Pump 1
8T-3035 Hydraulic Line 1
C 126-6918(4)
or
126-6919(5) Lifting Bracket 1
126-6920 Handle Rod 1
5D-1972 Bolt 2
D 229-3639 Overhaul Protection Gp 1
F 183-3424 Water and Temperature Resistant Grease 1
(1) Operating pressure is 40000 1520 kPa (5800 220 psi).
(2) Operating pressure is 125000 4920 kPa (18130 715 psi).
(3) There are three pumps that are listed in the tool chart. Any one of the pumps may be used for this procedure.
(4) Use with V-engines
(5) Use with In-line engines
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Tooling (D) provides all the protective covers and plugs for one cylinder. Use these protective covers in order to maximize the protection during these procedures.
Thoroughly clean the sealing surfaces on top of the cylinder block assembly.
Remove all debris from the inside of the cylinder liner and top of the piston. Apply clean engine oil to the inside of the cylinder liner.
Earlier engines may have RTV coating on the cylinder head studs. Remove all debris from the holes in the cylinder block. Thoroughly clean the cylinder head studs and the top surface of the cylinder block. Paint the cylinder head studs if the cylinder head studs were cleaned to the bare metal.
If the cylinder head studs were removed, use the following procedure to install the cylinder head studs:
Before installing the cylinder head studs, coat the lower half of the cylinder head studs with Tooling (F). Apply an extra bead of grease around the cylinder head studs at the base of the cylinder head studs on the face of the block. This will help ensure that the counterbore in the top of the block is full of grease.
Thoroughly clean the top of the cylinder block.
Install the cylinder head studs in the block and tighten to a torque of 100 20 N m (75 15 lb ft).
Coat the entire length of the cylinder head studs with Tooling (F) after the cylinder head studs are installed in the cylinder block.
Always install the seal plates after the cylinder liners are installed. Aluminum debris shaved from the plates by the cylinder liners will prevent the cylinder liners from sealing if the plates are installed first.
Illustration 1 g01337539
Cuffed liner
Note: The following Steps are for cuffed liners and for noncooled liners.
Put a new O-ring seal on both sides of seal plate (9) and seal plate (11). Put new O-ring seals on the seal adapters. Install the seal plates and the seal adapters.
Put combustion gasket (10) in position on top of the cylinder liner.
Attach Tooling (C) and a suitable lifting device to the cylinder head. The weight of the cylinder head is approximately 204 kg (450 lb).
Carefully lower the cylinder head onto the cylinder head studs.
Be sure that the cylinder head assembly is seated on the dowels and be sure that the seal plates and the O-ring seals are seated properly.
Install the nuts and the washers in order to hold the cylinder head. Tighten the nuts by hand. Note: Lubricate the washer face and the threads of the cylinder head studs with Tooling (F) before assembly.
Illustration 2 g01337535
Install Tooling (A) over the nuts, and attach Tooling (B) to Tooling (A).
Tighten collars (4) with a ratchet lever (1/2 inch drive). Loosen the collars for 1/4 turn.
Personal injury can result from oil under high pressure.DO NOT allow high pressure oil to contact skin.Wear appropriate protective equipment while working with high pressure oil systems.
Note: The stud tensioner tool groups in Tooling (A) require different operating pressure.
Run the pump in Tooling (B) until the operating pressure is registered on the gauge.
Place dowel handle (5) through the slot in each pedestal in order to tighten each nut. Tighten each nut hand tight.
Slowly release the hydraulic pressure, and repeat Steps 14 and 15.
Remove Tooling (A) from the cylinder head assembly, the cylinder head studs, and the nuts.


Parts water JOHNSON:

0391388
 
0391388 WATER PUMP REPAIR KIT, (includes impeller hou sing)
J10ECSE, J10ELCID, J10ELCNS, J10ELCTC, J15ECIS, J15ECNC, J15ECSD, J15ECTR
0326994
 
0326994 WATER TUBE, Std.
J10ELCID, J10ELCNS, J10ELCRA, J10ELCTC, J15ECIS, J15ECNC, J15ECRM, J15ECTR
0326995
 
0326995 WATER TUBE, Long
J10ELCID, J10ELCNS, J10ELCRA, J10ELCTC, J15ECIS, J15ECNC, J15ECRM, J15ECTR
0326885
 
0326885 WATER RESTRICTOR
J10ECDB, J10ECOM, J10ECUE, J10ELCID, J10ELCNS, J10ELCRA, J10ELCTC, J15ECDE, J15ECIS, J15ECNC, J15ECOB, J15ECRM, J15ECTR, J15ECUD
0391698
 
0391698 WATER PUMP REPAIR KIT
BJ10FAEDC, BJ10FAEUR, BJ10FDLEDR, BJ10FDLEUA, BJ15FAEDR, BJ15FAEUA, BJ8FRBEDC, BJ8FRBEUR, HJ15KCF, HJ15KCLN, HJ15KCLO, J10ECCD, J10ECDB, J10ECES, J10ECOM, J10ECUE, J10EEIR, J10EENA, J10EEOE, J10EERB, J10EESC, J10EETM, J10ELCID, J10ELCNS, J10ELCRA, J1
0393560
 
0393560 WATER PUMP REPAIR KIT, (includes impeller hsg
J10ELCNS, J10ELCTC, J15ECNC, J15ECTR
Back to top