0341553 JOHNSON WATER TUBE


0341553 WATER TUBE JOHNSON AM55RSLD, HJ45RCLEDS, HJ45RCLEUC, HJ55RSLC, HJ55RSLW, J40WREES, J40WRLSIR, J40WRLSSC, J45RCEOD, J55RSLG, J55WRLSIR, J55WRLSOE, J55WRLSRB, J55WRLSSC, SJ40RPB, SJ40RPH, SJ40RPLT2, SJ55RSLM2 WATER
0341553 WATER TUBE JOHNSON
Rating:
8

Buy WATER TUBE 0341553 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 94
 

BRP JOHNSON entire parts catalog list:

AM55RSLD, J55WREES, J55WRLEES, J55WRYEES 1999
HJ45RCLEDS, J45RCLEDS, SJ45RSLH 1996
HJ45RCLEUC, J45RCLEUC, SJ45RSLB 1997
HJ55RSLC, J55RSLC, SJ55RSC, SJ55RSLC, SJ55RSYC 1997
HJ55RSLW, J55RSLW, SJ55RSLW, SJ55RSW, SJ55RSYW 1996
J40WREES, J40WRLEES, J40WRYEES 1999
J40WRLSIR, J40WRSIR, J40WRYSIR 2001
J40WRLSSC, J40WRSSC, J40WRYSSC 2000
J45RCEOD, J45RCLEOD 1995
J55RSLG 1995
J55WRLSIR, J55WRSIR, J55WRYSIR 2001
J55WRLSOE, J55WRYSOB 2005
J55WRLSRB, J55WRLSRG, J55WRYSRM 2004
J55WRLSSC, J55WRSSC, J55WRYSSC 2000
SJ40RPB, SJ40RPLB, SJ40RPYB 1997
SJ40RPH, SJ40RPLH, SJ40RPYH 1996
SJ40RPLT2, SJ40RPT2, SJ40RPYT2 1998
SJ55RSLM2, SJ55RSM2, SJ55RSYM2 1998

Information:


Illustration 1 g00776934
HEUI injector
Illustration 2 g00947899
Top view of engine
Illustration 3 g00947900
Schematic
Illustration 4 g00947952
P2 ECM connectorTest Step 1. Inspect Electrical Connectors and Wiring
Electrical shock hazard. The electronic unit injector system uses 90-120 volts.
Turn the keyswitch to the OFF position. A strong electrical shock hazard is present if the keyswitch is not turned OFF.
Thoroughly inspect the J2/P2 ECM connector and the J300/P300 injector harness connector. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the J300/P300 injector harness connector that are associated with the injector solenoids.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the J300/P300 injector harness connector for proper mating of the connector.
Check the harness and wiring for abrasions and for pinch points from the injectors to the ECM.Expected Result:All connectors, pins, and sockets should be completely coupled and/or inserted. The harness and wiring should be free of corrosion, abrasion, and pinch points.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Perform the following repair:Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Diagnostic Codes Regarding Injector Solenoids
Connect Cat ET to the service tool connector.
Turn the keyswitch to the ON position.
Monitor the "Logged Diagnostic Codes" screen on Cat ET.Expected Result:One or more of the listed codes have been logged:
1-11 Injector Cylinder #1 fault
2-11 Injector Cylinder #2 fault
3-11 Injector Cylinder #3 fault
4-11 Injector Cylinder #4 fault
5-11 Injector Cylinder #5 fault
6-11 Injector Cylinder #6 faultResults:
OK - One or more of the codes that are listed above are logged. Proceed to Test Step 4.
Not OK - None of the codes that are listed above are logged. Proceed to Test Step 3.Test Step 3. Check The Variation of the Injectors between Cylinders
Start the engine.
Allow the engine to warm up to normal operating temperature (77 °C (171 °F)).
After the engine is warmed to operating temperature, access the "Cylinder Cutout Test" by accessing the following display screens in order:
"Diagnostics"
"Special Tests"
"Cylinder Cutout Test"
Shut off all parasitic loads such as the air compressors which could affect the results of the test.
Set the engine speed at low idle.
Use the cylinder cutout test in order to cut out individual cylinders.
Monitor the "Fuel Position" on the service tool display.
Perform the test three times.
Verify that cutting out a specific cylinder causes only a slight change to the "Fuel Position" of the other cylinders.
Compare the results that are found when other cylinders are cut out.Note: A mechanical problem with the injector or the cylinder may exist if a specific cylinder is cut out and only a slight change occurs to the "Fuel Position" of the other cylinders.
Check Cat ET for any active diagnostic codes or any logged diagnostic codes that are new after the test.Expected Result:One or more diagnostic codes for the injectors are active or logged as a result of the cylinder cutout test.Results:
OK - One or more diagnostic codes for the injectors are active or logged as a result of the cylinder cutout test. Proceed to Test Step 4.
Not OK - The injectors are OK electronically.Repair: Refer to Testing and Adjusting, "Fuel System" for additional information.STOPTest Step 4. Use the "Injector Solenoid Test" to Test the Injector Solenoids
Start the engine.
Allow the engine to warm up to normal operating temperature (77 °C (171 °F)).
Turn the keyswitch to the OFF position.
Turn the keyswitch to the ON position.
After the engine is warmed to operating temperature, access the "Injector Solenoid Test" by accessing the following display screens in order:
"Diagnostics"
"Diagnostic Tests"
"Injector Solenoid Test"
Activate the test.Note: The test is in the "Diagnostic Tests". Do not confuse the "Injector Solenoid Test" with the cylinder cutout test. The cylinder cutout test is used to shut off fuel to a specific cylinder while the engine is running. The injector solenoid test is used in order to actuate the injector solenoids. This allows the click of the injector solenoids to be heard when the engine is not running in order to determine that the circuit is functioning properly.
As each solenoid is energized by the ECM an audible click can be heard at the valve cover. Listen for a click at each valve cover. A black square will appear over the cylinder number when the cylinder is being fired.
Perform the injector solenoid test at least two times.Expected Result:All cylinders indicate "OK".Results:
OK - There is not a problem in the circuit for the injectors at this time.Repair: If an intermittent problem is suspected, refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
OPEN - Note the cylinders that indicate "OPEN". Proceed to Test Step 6.
SHORT - Note the cylind


Parts water JOHNSON:

0437772
 
0437772 WATER PUMP REPAIR KIT, (Includes impeller hou ing)
HJ45RCLEDS, HJ55RSLW, HJ55WMLM, J45RCEOD, J50TTLEDC, J55RSLG, J60TTLEDR, SJ40RPH
0437771
 
0437771 WATER PUMP REPAIR KIT
J45RCEOD, J50TTLEOS, J55RSLG, J60TTLEOC, J65RSLC, J65WMLEOC, J70TTLEOR
0341551
 
0341551 WATER TUBE
AM55RSLD, HJ45RCLEDS, HJ45RCLEUC, HJ55RSLC, HJ55RSLW, J40WREES, J40WRLSIR, J40WRLSSC, J45RCEOD, J55RSLG, J55WRLSIR, J55WRLSSC, SJ40RPB, SJ40RPH, SJ40RPLT2, SJ55RSLM2
0341552
 
0341552 WATER TUBE
AM55RSLD, HJ45RCLEDS, HJ45RCLEUC, HJ55RSLC, HJ55RSLW, HJ55WMLZ, J40WREES, J40WRLSIR, J40WRLSSC, J45RCEOD, J55APRL, J55APRLSOM, J55APRLSRA, J55MLSOR, J55MLSRC, J55MRL, J55RSLG, J55WRLSIR, J55WRLSOE, J55WRLSRB, J55WRLSSC, J55WRLSTM, SJ40RPB, SJ40RPH, S
0438593
 
0438593 WATER PUMP REPAIR KIT, (Includes impeller hou sing)
HJ45RCLEUC, HJ55RSLC, HJ55WMLZ, SJ40RPB, SJ40RPLT2, SJ55RSLM2
5000308
WATER PUMP REPAIR KIT, (Includes impeller hou ing)
5000308 WATER PUMP REPAIR KIT, (Includes impeller hou ing)
AM55RSLD, J40WREES, J40WRLSIR, J40WRLSSC, J55APRL, J55APRLSOM, J55APRLSRA, J55MLSOR, J55MLSRC, J55MRL, J55WRLSIR, J55WRLSOE, J55WRLSRB, J55WRLSSC, J55WRLSTM, SJ40RPLT2, SJ55RSLM2
Back to top