0393560 JOHNSON WATER PUMP REPAIR KIT, (includes impeller hsg


0393560 WATER PUMP REPAIR KIT, (includes impeller hsg JOHNSON J10ELCNS, J10ELCTC, J15ECNC, J15ECTR WATER
0393560 WATER PUMP REPAIR KIT, (includes impeller hsg JOHNSON
Rating:
33

Buy WATER PUMP REPAIR KIT, (includes impeller hsg 0393560 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$29.03
 

22-06-2022

-: -
Peach Motor Parts PM-WPMP-0037A Water Pump Repair Kit (With Housing); Fits Johnson Evinrude OMC BRP�: 0386697, 386697, 0393560, 393560, 0391388, 391388, 0394711, 394711, 0386886, 386886, 039169 Made b
New
Number on catalog scheme: 63
 

Compatible models:

BRP JOHNSON entire parts catalog list:

J10ELCNS, J10RCNS, J10RLCNS, J10SELCNS 1982
J10ELCTC, J10RCTC, J10RCTR, J10RLCTC, J10RLCTR, J10SELCTC 1983
J15ECNC, J15RCNC, J15RLCNC 1982
J15ECTR, J15ELCTR, J15RCTA, J15RCTR, J15RLCTA, J15RLCTR 1983

Information:

Recommended Actions
Diagnostic Codes, Event Codes, and Electrical Power Supply to the ECM
Certain diagnostic codes and/or event codes may prevent the engine from starting. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes. Troubleshoot any codes that are present before continuing with this procedure.Note: If Cat ET will not communicate with the ECM, the problem is most likely with the electrical power supply to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test".Fuel Supply
Visually check the fuel level. Do not rely on the fuel gauge only. If necessary, add fuel. If the engine has been run out of fuel, it will be necessary to prime the fuel system. Refer to Operation and Maintenance Manual for the correct procedure.
Check the fuel lines for the following problems: restrictions, collapsed lines and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.
Check the fuel tank for foreign objects which may block the fuel supply.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Prime the fuel supply system if any of the following procedures have been performed:
Replacement of the fuel filters
Service on the low pressure fuel supply circuit
Replacement of unit injectorsNote: A sight glass in the supply line is helpful in diagnosing air in the fuel.
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.
Check fuel flow after the fuel filters. If the fuel flow is low, replace the fuel filters. If the fuel flow is still low, check the following items: fuel transfer pump, fuel transfer pump coupling and fuel pressure regulating valve. Starting Aids (if applicable)
If cold ambient conditions exist, check operation of starting aids. Refer to Troubleshooting, "Ether Starting Aid - Test".
Ensure the proper operation of the jacket water heater. Repair the jacket water heater and/or replace the jacket water heater, if necessary.
Check for presence of solidified fuel (wax). Engine Shutdown Switches (if applicable)
The engine shutdown switches should be in the OFF position. Use Cat ET to verify the status of the shutdown switches. When a shutdown occurs, the keyswitch must be turned to the OFF position for at least 15 seconds before restarting the engine.Engine Speed/Timing
Crank the engine and observe the engine speed on the Cat ET status screen. If Cat ET indicates zero rpm, refer to Troubleshooting, "Speed/Timing - Test". Note: Upon initial cranking, the status for engine speed may indicate that the engine speed signal is abnormal. This message will be replaced with an engine speed once the ECM is able to calculate a speed from the signal.
Ensure that the timing reference gear is installed correctly. The engine will not start if the gear was installed backward. Check for proper orientation between the crankshaft and camshaft drive gears. Correct the orientation and/or replace the drive gear, if necessary. Refer to the Disassembly and Assembly manual. Unit Injectors
Perform the "Injector Solenoid Test" on Cat ET in order to determine if all of the injector solenoids are being energized by the ECM. Refer to Troubleshooting, "Injector Solenoid - Test" for additional information.Combustion
Check for mechanical problems in the combustion system.


Parts water JOHNSON:

0391388
 
0391388 WATER PUMP REPAIR KIT, (includes impeller hou sing)
J10ECSE, J10ELCID, J10ELCNS, J10ELCTC, J15ECIS, J15ECNC, J15ECSD, J15ECTR
0325253
 
0325253 WATER COVER, Cylinder head
J10ELCID, J10ELCNS, J10ELCTC, J15ECIS, J15ECNC, J15ECTR
0326994
 
0326994 WATER TUBE, Std.
J10ELCID, J10ELCNS, J10ELCRA, J10ELCTC, J15ECIS, J15ECNC, J15ECRM, J15ECTR
0326995
 
0326995 WATER TUBE, Long
J10ELCID, J10ELCNS, J10ELCRA, J10ELCTC, J15ECIS, J15ECNC, J15ECRM, J15ECTR
0326885
 
0326885 WATER RESTRICTOR
J10ECDB, J10ECOM, J10ECUE, J10ELCID, J10ELCNS, J10ELCRA, J10ELCTC, J15ECDE, J15ECIS, J15ECNC, J15ECOB, J15ECRM, J15ECTR, J15ECUD
0391698
 
0391698 WATER PUMP REPAIR KIT
BJ10FAEDC, BJ10FAEUR, BJ10FDLEDR, BJ10FDLEUA, BJ15FAEDR, BJ15FAEUA, BJ8FRBEDC, BJ8FRBEUR, HJ15KCF, HJ15KCLN, HJ15KCLO, J10ECCD, J10ECDB, J10ECES, J10ECOM, J10ECUE, J10EEIR, J10EENA, J10EEOE, J10EERB, J10EESC, J10EETM, J10ELCID, J10ELCNS, J10ELCRA, J1
Back to top