0318672 WRIST PIN JOHNSON
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, J10ECSE, J15ECSD
WRIST
Price: query
Rating:
Number on catalog scheme: 3
Compatible models:
BRP JOHNSON entire parts catalog list:
- CRANKSHAFT & PISTON » 0318672
10E76G, 10E76H, 10E76R, 10EL76G, 10EL76H, 10EL76R, 10R76G, 10R76H, 10R76R, 10RL76G, 10RL76H, 10RL76R 1976
10E77A, 10EL77A, 10R77A, 10RL77A 1977
10E78M, 10EL78M, 10R78M, 10RL78M, 10SEL78M 1978
10EL79B, 10R79B, 10RL79B, 10SEL79B 1979
15E74G, 15E74S, 15EL74G, 15EL74S, 15R74G, 15R74S, 15RL74G, 15RL74S 1974
15E75C, 15EL75C, 15R75C, 15RL75C 1975
15E76A, 15E76R, 15EL76A, 15EL76R, 15R76A, 15R76R, 15RL76A, 15RL76R 1976
15E77M, 15EL77M, 15R77M, 15RL77M 1977
15E78B, 15EL78B, 15R78B, 15RL78B 1978
15E79E, 15EL79E, 15R79E, 15RL79E 1979
J10ECSE, J10ELCSE, J10RCSE, J10RLCSE, J10SELCSE 1980
J15ECSD, J15ELCSD, J15RCSD, J15RLCSD 1980
Information:
Table 1
3500B Generator Set Engine Oil Change Intervals
Engine Sump Capacity Oil Change Interval
Engines With a Standard Sump
3512B 318 L (84 US gal) Every 500 Service Hours
3516B 405 L (107 US gal)
Engines With a Deep Sump
3512B 625 L (165 US gal) Every 1000 Service Hours
3516B 807 L (213 US gal) Drain the Oil
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Do not drain the oil when the engine is cold. As the oil cools, suspended waste particles settle on the bottom of the oil pan. The waste particles are not removed when the cold oil is drained. Drain the crankcase when the oil is warm. This draining method allows proper draining of the waste particles that are suspended in the oil.Failure to follow this recommended procedure will allow the waste particles to be recirculated through the engine lubrication system with the new oil.
After the engine has been operated at normal operating temperature, STOP the engine.
Drain the oil according to the equipment on the engine.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00750439
(1) Oil drain
Open oil drain (1). After the oil has drained, close the oil drain.
If a suction device is inserted into the oil pan, ensure that the suction device is clean. This will prevent dirt from entering into the oil pan. Be careful not to strike the engine oil suction tubes or the piston cooling jets.
If a suction device that attaches to the oil drain is used, ensure that the suction device is clean. Attach the suction device to the oil drain. Open the oil drain. After the oil has drained, close the oil drain and remove the suction device.
If the oil drain valve has a “quick connect” coupling, attach the coupling. Open the drain valve in order to drain the crankcase. After the oil has drained, close the drain valve. Disconnect the coupling.
Replace the engine oil filter elements before filling the crankcase with new oil. Replace the Oil Filter Elements
Replace the engine oil filters when either of the following conditions occur:
Every oil change
The engine oil filter differential pressure reaches 103 kPa (15 psi).
The oil filter elements have been used for 1000 service hours.Note: Do not attempt to clean the used oil filters. Used oil filters will retain waste particles. The used oil filters would not filter the oil properly.Service tools are available to aid in the service of oil filters. Consult your Caterpillar dealer for the part names and the part numbers. Follow the instructions that are supplied with the service tools. If the service tools are not used, perform the following appropriate procedure.Replacing the Engine Oil Filters With the Engine Stopped
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Perform the following procedure after the oil has been drained.
Illustration 2 g00750438
(1) Drain
(2) Drain valve
(3) Plug
(4) Bolts
(5) Cover
Connect a hose to drain (1). Place the other end of the hose into a suitable container in order to collect the oil.
Open drain valve (2). Remove plug (3). Allow the oil to drain. Clean the plug and install the plug. Close the drain valve. Remove the hose from the drain. Note: Some oil will remain in the housing after the oil has been drained. This oil will pour out of the housing when cover (5) is removed. Prepare to catch the oil in a suitable container. Clean up any spilled oil with absorbent towels or pillows. DO NOT use absorbent particles to clean up the oil.
Personal injury can result from parts and/or covers under spring pressure.Spring force will be released when covers are removed.Be prepared to hold spring loaded covers as the bolts are loosened.
Be alert to the spring force. Gradually loosen but do not remove bolts (4). Before removing the bolts, pry the cover (5) loose or tap the cover with a rubber mallet in order to relieve any spring pressure. Remove cover (5).