78036 Mariner BASE, LOWER - REVERSE LOCKING - NOT PART OF GEAR HOUSING


78036 BASE, LOWER - REVERSE LOCKING - NOT PART OF GEAR HOUSING Mariner 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7075524, 7090524, 7115520 BASE
78036 BASE, LOWER - REVERSE LOCKING - NOT PART OF GEAR HOUSING Mariner
Rating:
68

Buy BASE, LOWER - REVERSE LOCKING - NOT PART OF GEAR HOUSING 78036 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 49
 

Mariner entire parts catalog list:

7045217 1987,1988,1989
7050200 1980,1982,1983,1985,1986
7050716 1986
7050717 1987,1988,1989,1990
7060312PC 1989
7060524 1984,1985,1986,1989,1990
7070509 1979
7070520 1980,1982,1983
7075524 1984,1985,1986
7090524 1984,1985,1986,1987,1988
7115520 1980

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-4030 Thread Lock Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01784893
Typical example
Ensure that the turbocharger is clean and free from damage. Inspect the turbocharger for wear. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect" for more information. If the turbocharger is worn, the complete turbocharger must be replaced.
Test wastegate actuator (20) for correct operation. Refer to System Operation, Testing and Adjusting, "Turbocharger Inspect". If the wastegate actuator is damaged or the wastegate actuator does not operate within the specified limits, the complete turbocharger must be replaced.
Illustration 2 g01782773
Clean the gasket surfaces of the exhaust manifold (1). If necessary, install studs (18) to the exhaust manifold. Tighten the studs to a torque of 18 N m (13 lb ft). Note: Support the exhaust manifold during installation of the turbocharger.
Install a new gasket (16) to exhaust manifold (1).
Position turbocharger (13) on exhaust manifold (1).
Install nuts (14). Tighten the nuts to a torque of 44 N m (32 lb ft).
Ensure that tube assembly (6) is clean and free from damage. Replace any damaged components.
Position a new gasket (15) and bolts (17) onto tube assembly (6).
Install tube assembly (6) to turbocharger (13). Tighten bolts (17) finger tight.
Install exhaust manifold (1) and the assembly of the turbocharger to the cylinder head. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install" for the correct procedure.
Remove the plug from oil inlet port (19). Refer to Illustration 1. Lubricate the turbocharger bearings with clean engine oil through the oil inlet port. Rotate the wheel of the compressor several times in order to lubricate the bearings.
Ensure that tube assembly (2) is clean and free from damage. Replace any damaged components.
Install banjo bolt (11) and new sealing washers (12) to tube assembly (2).
Illustration 3 g01780893
Install banjo bolt (7) and new sealing washers (9) to tube assembly (2).
Install tube assembly (2) to turbocharger (13). Tighten banjo bolt (11) finger tight. Refer to Illustration 2.
Tighten banjo bolt (7) to the cylinder block finger tight.
Position a new gasket (8) between the flange of tube assembly (6) and the cylinder block. Install bolts (10) finger tight.
Tighten banjo bolt (7) to a torque of 20 N m (14 lb ft). Tighten bolts (10) to a torque of 22 N m (16 lb ft).
Tighten banjo bolt (11) to a torque of 20 N m (14 lb ft). Tighten bolts (17) to a torque of 9 N m (80 lb in). Refer to Illustration 2.
Install bolt (3) for the tube clip to the cylinder block. Tighten bolt (3) to a torque of 44 N m (32 lb ft).
Install bolt (5) and spacer (4) for the tube clip to the cylinder block. Tighten bolt (5) to a torque of 44 N m (32 lb ft).
If the turbocharger has an exhaust elbow, install the exhaust elbow. Refer to Disassembly and Assembly, "Exhaust Elbow - Remove and Install".
Connect the exhaust pipe.
Connect the air outlet hose to turbocharger (13). If the engine has an air pipe, install the air pipe and install the gasket to the cylinder head. Apply Tooling (A) to the fasteners for the air pipe. Tighten the fasteners to a torque of 22 N m (16 lb ft).Tighten the hose clamps to a torque of 5 N m (44 lb in).Note: If the air outlet hose has a reflective heat shield, ensure that the reflective heat shield is installed toward the engine.
Connect the air inlet hose to turbocharger (13).


Parts base Mariner:

86295
 
86295 BASE, FUEL PUMP
7090520, 7090524, 7090529, 7115520, 7115529, 7140629
14430 3
 
14430 3 BASE
7002201DK, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 70404119D, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7045217, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7055207GD, 7055207HB,
Back to top