41296M Mariner BEARING, CRANKSHAFT-LOWER


41296M BEARING, CRANKSHAFT-LOWER Mariner 7040206, 7048321, 7055324, 7055524 BEARING
41296M BEARING, CRANKSHAFT-LOWER Mariner
Rating:
73

Buy BEARING, CRANKSHAFT-LOWER 41296M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

Mariner entire parts catalog list:

7040206 1986,1987,1988,1989
7048321 1981
7055324 1984,1985,1988,1989
7055524 1984,1985

Information:

The following background information is related to this procedure:Electronically Controlled Wastegate
Illustration 1 g03795243The engine has a turbocharger with an electronically controlled wastegate (1). Typically, the wastegate is a mechanical valve that is used in the turbocharger in order to regulate the intake manifold pressure to a set value.The control system for the electronically controlled wastegate precisely regulates the intake manifold pressure by using a wastegate regulator to control the wastegate.The required intake manifold pressure is calculated by the software that is contained in the ECM. The ECM uses the wastegate regulator to control the wastegate in order to provide the precise value of intake manifold pressure. The solenoid in the wastegate regulator is controlled by a PWM signal from the ECM.Suction Control Valve for the High-Pressure Fuel Pump
Illustration 2 g03795285The high-pressure fuel pump is equipped with a suction control valve (2). The suction control valve precisely controls the amount of fuel that enters the high-pressure fuel pump.The amount of fuel that is required is calculated by the software that is contained in the ECM. The solenoid in the suction control valve is controlled by a PWM signal from the ECM.
Illustration 3 g03812182
Schematic for the solenoid valves connected to the engine ECM
Illustration 4 g03812187
Pin locations on the P2 connector for the solenoid valves
(16) Wastegate regulator PWM signal
(24) Wastegate regulator return
(69) High pressure fuel pump suction control valve return
(77) High pressure fuel pump suction control valve PWM signal Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P2/J2 ECM connector and the solenoids. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector and the solenoid connectors that are associated with the active diagnostic code.
C. Check the screw for the ECM connector for the correct torque of 6 N m (53 lb in).
D. Check the harness for corrosion, abrasion, and pinch points from the solenoids to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all of the seals are properly in place and ensure that the connectors are correctly coupled.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 2.
2. Check for Active Diagnostic Codes
A. Turn the keyswitch to the OFF position.
B. Connect the electronic service tool to the diagnostic connector.
C. Turn the keyswitch to the ON position. Wait at least 20 seconds for activation of the diagnostic codes.
D. Verify if any of the diagnostic codes that are listed in Table 1 are active.
E. Turn the keyswitch to the OFF position.
Diagnostic codes
Result: An XXXX-5 diagnostic code is active.
Proceed to Test Step 3.
Result: An XXXX-6 diagnostic is active.
Proceed to Test Step 5.
3. Create a Short Circuit at the Harness Connector for the Solenoid
A. Turn the keyswitch to the OFF position.
B. Disconnect the


Parts bearing Mariner:

82313M
 
82313M BEARING, NEEDLE
7040207, 7040208, 7040328, 7040507, 7048207, 7048227, 7048321, 7060507, 7060528
82304M
 
82304M BEARING
7040207, 7040208, 7040328, 7040507, 7048207, 7048227, 7048321, 7060507, 7060528
82353M
BEARING, NEEDLE
82353M BEARING, NEEDLE
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
82312M
 
82312M BEARING, NEEDLE
7048207, 7048227, 7048321, 7055524, 7060507, 7060522, 7060528
98944M
 
98944M BEARING, CONNECTING RD
7048227, 7048321, 7060522
83880M
 
83880M BEARING CARRIER
7040202, 7040206, 7040208, 7040328, 7040706, 7040716
97837M
 
97837M BEARING, CENTER MAIN
7040202, 7040206, 7040706, 7040716, 7048321, 7055324, 7055524, 7060522
41298M
 
41298M BEARING, CONNECTING ROD
7048321, 7055324, 7055524, 7060522
Back to top